Apex
April 17th, 2009, 10:25 AM
I ordered the full clear tail kit with integrated signals from a supplier. It
came in yesterday and I spent about an hour last night working on it. I figured that some of the people who are a little gun shy about doing this mod may wish to check it out.
This is prepping for the fender eliminator I plan on doing.
Before:
http://www.ninjette.org/forums/picture.php?albumid=138&pictureid=1354
The Kit:
http://www.ninjette.org/forums/picture.php?albumid=138&pictureid=1341
http://www.ninjette.org/forums/picture.php?albumid=138&pictureid=1343
Disconnect the turn signals from the fender by removing this screw and the plate, then pulling out the inner plate. Then go back up to the wiring and remove the connectors that signal goes to. DO ONE AT A TIME to avoid confusing the wiring. Once disconnected, you can pull the wiring and the signal off:
http://www.ninjette.org/forums/picture.php?albumid=138&pictureid=1344
Cut the wires (if required) and strip back some of the insulation for the butt connectors, install the socket into the housing. For some extra clearance, I removed the handle using a 12mm and 10mm socket. Here is a pic:
http://www.ninjette.org/forums/picture.php?albumid=138&pictureid=1348
Reinstall the lamp:
http://www.ninjette.org/forums/picture.php?albumid=138&pictureid=1346
Install the new clear cover:
http://www.ninjette.org/forums/picture.php?albumid=138&pictureid=1347
You can see the extension I put on to reach the new socket. Just crimp down on the connectors and have some electrical tape handy to wrap around the connectors to keep some water out (that white connector is what came with that, I left it on for easy identification. It was cut and connected to the two hanging wires):
http://www.ninjette.org/forums/picture.php?albumid=138&pictureid=1348
Don't sweat about what wire to connect to where. It is a DC circuit. Positive or negative does not matter here, the power will still flow through the bulb. Just make sure you are using the two wires that went to the original signal! So once you have it all connected, you can test it out and you should see this:
http://www.ninjette.org/forums/picture.php?albumid=138&pictureid=1349
For a comparison, I took a picture of the old assembly flashing on the right side (FYI: just so you know, the camera told me about how much light was available by each signal. My shutter clicked like it was a datytime shot with the upgraded signal, but it stayed open for a bit with the old ones, a noticeable difference. That tells me the new signal locations puts out more light):
http://www.ninjette.org/forums/picture.php?albumid=138&pictureid=1350
Now do the exact same thing to the other side:
http://www.ninjette.org/forums/picture.php?albumid=138&pictureid=1352
I decided to leave the red cover on because I did not like having it all clear. So now you should now see this:
http://www.ninjette.org/forums/picture.php?albumid=138&pictureid=1351
http://www.ninjette.org/forums/picture.php?albumid=138&pictureid=1353
If anyone plans on doing this mod and wants to ask some questions, feel free to ask. I know I am not the only person who has done this, so if I don't answer, someone else can. :D
came in yesterday and I spent about an hour last night working on it. I figured that some of the people who are a little gun shy about doing this mod may wish to check it out.
This is prepping for the fender eliminator I plan on doing.
Before:
http://www.ninjette.org/forums/picture.php?albumid=138&pictureid=1354
The Kit:
http://www.ninjette.org/forums/picture.php?albumid=138&pictureid=1341
http://www.ninjette.org/forums/picture.php?albumid=138&pictureid=1343
Disconnect the turn signals from the fender by removing this screw and the plate, then pulling out the inner plate. Then go back up to the wiring and remove the connectors that signal goes to. DO ONE AT A TIME to avoid confusing the wiring. Once disconnected, you can pull the wiring and the signal off:
http://www.ninjette.org/forums/picture.php?albumid=138&pictureid=1344
Cut the wires (if required) and strip back some of the insulation for the butt connectors, install the socket into the housing. For some extra clearance, I removed the handle using a 12mm and 10mm socket. Here is a pic:
http://www.ninjette.org/forums/picture.php?albumid=138&pictureid=1348
Reinstall the lamp:
http://www.ninjette.org/forums/picture.php?albumid=138&pictureid=1346
Install the new clear cover:
http://www.ninjette.org/forums/picture.php?albumid=138&pictureid=1347
You can see the extension I put on to reach the new socket. Just crimp down on the connectors and have some electrical tape handy to wrap around the connectors to keep some water out (that white connector is what came with that, I left it on for easy identification. It was cut and connected to the two hanging wires):
http://www.ninjette.org/forums/picture.php?albumid=138&pictureid=1348
Don't sweat about what wire to connect to where. It is a DC circuit. Positive or negative does not matter here, the power will still flow through the bulb. Just make sure you are using the two wires that went to the original signal! So once you have it all connected, you can test it out and you should see this:
http://www.ninjette.org/forums/picture.php?albumid=138&pictureid=1349
For a comparison, I took a picture of the old assembly flashing on the right side (FYI: just so you know, the camera told me about how much light was available by each signal. My shutter clicked like it was a datytime shot with the upgraded signal, but it stayed open for a bit with the old ones, a noticeable difference. That tells me the new signal locations puts out more light):
http://www.ninjette.org/forums/picture.php?albumid=138&pictureid=1350
Now do the exact same thing to the other side:
http://www.ninjette.org/forums/picture.php?albumid=138&pictureid=1352
I decided to leave the red cover on because I did not like having it all clear. So now you should now see this:
http://www.ninjette.org/forums/picture.php?albumid=138&pictureid=1351
http://www.ninjette.org/forums/picture.php?albumid=138&pictureid=1353
If anyone plans on doing this mod and wants to ask some questions, feel free to ask. I know I am not the only person who has done this, so if I don't answer, someone else can. :D