Go Back > Blogs > Ghostt

Rate this Entry

Who wants to see a MOSFET R/R upgrade?

Posted December 10th, 2014 at 09:15 PM by Ghostt
Updated February 4th, 2015 at 10:57 PM by Ghostt (Update 12/12/14)

Yup, it's time to lose that old school SHUNT STYLE R/R to a more accurate, and dependable MOSFET R/R.

Mosfets run cooler, plus they’re more efficient. So if your stock R/R unit has burned out, maybe it’s time to move to a newer Mosfet type unit as shown here. Mosfet R/Rs model names start with the letters FH. Old type models start with SH.

I have the R/R (FH010) already, just waiting for a few little pieces to show up.

Stay tuned folks, I promise a nice clean and easy installation, with pictures of course.

Update 12/12/14

Pieces & Parts.

Okay I ordered the connectors from Eastern Beaver ( )

They offer a great selection and options to make the conversion, easy, and reliable, depending on the level you wish to take it to.

I myself am choosing to do this modification as a plug-n-play version.

The advantage is, if needed I can plug the OEM R/R back in without any issues or problems.

Why would I want to switch back you say?

The answer is my OEM R/R is in working condition, and when I travel I will carry it as a spare, just in case of emergency.

The connectors I ordered will allow me to make an adapter harness/pigtail. All I have to do is supply some wire.

UPDATE 01/21/2015

Okay so I've made the wiring adapter pigtail, only to find out I ordered the wrong connector that would plug into the bike's wiring.

So I cut off the old one that was attached to the OEM R/R, and used that instead, which sucks.

There is one wire that is no longer needed and that's the brown one, so I removed it from the OEM male connector.

The 3 yellow wires are from the stator, so it makes no difference which order they are in when plugging into the gray plug on the R/R, no polarity issues.

The black/yellow wire is the negative, to that goes on the right/outside, and the white/red wire goes to the left/inside, due to polarity. The middle is left empty for the black plug.

But it's all done, and I will install it tomorrow.

UPDATE 01/22/2015

Installed and working perfectly, so far. It's a tight fit, and only able to use the top bolt for mounting, but it's not going anywhere.


A worthwhile investment and upgrade that is needed to make the bike more dependable, and the R/R more efficient.

One most remember that the OEM SHUNT R/R dump all those unused amps to their heatsink, if you've converted to all LEDs to save those amps, it's slowly cooking the OEM SHUNT R/R, which only speeds up the failure process.

The MOSFET R/R is better at handling this, and more efficient, and a better R/R all together.

A quick lesson on MOSFETs,

MOSFET? What exactly is that? I knew the term from the audio industry but I figured I'd copy and paste the information verbatim for the purposes of explanation. From wikipedia:

The metal–oxide–semiconductor field-effect transistor (MOSFET, MOS-FET, or MOS FET) is a transistor used for amplifying or switching electronic signals. The basic principle of this kind of transistor was first patented by Julius Edgar Lilienfeld in 1925.
Fine, that's what it is. What does it do? Again from wiki:

In MOSFETs, a voltage on the oxide-insulated gate electrode can induce a conducting channel between the two other contacts called source and drain.
How does this affect a regulator rectifier? Well, the vast majority of Regulator/Rectifiers use a 'shunt' type regulator. What this does is shunt (source) voltage directly to (drain) ground when voltage exceeds the rating they were set for. This makes them hot as they dissipate the heat generated by constant shunting to ground.
In actual operation, they shunt until there is no more voltage and then resume operation. This can be a bad thing because when the regulator is shunted, the battery is not getting charged. If you add more drain, the regulator will actually shunt less and run cooler. Either way, the battery, which has to be maintained at a specific level of charge for normal operation, is not getting the amount of charge it needs. Factor in malfunctions which occur relatively frequently in any kind of mechanical switch and the benefit of using a MOSFET type switch becomes more clear.

The MOSFET switch shunts also, but less frequently and only until voltage returns to an acceptable level, not to complete dissipation. The result is, it runs cooler, and it is much more effective as a regulator, delivering continuous voltage to the battery, regardless of engine speed. With a standard shunt type regulator, the charge rate at the battery actually goes down with an increase in engine speed. It's more effective at idle rather than full throttle.

I did some online research and found that all available MOSFET type R/Rs are made by a single company in Japan. Shindengen is the name of it. Suzuki uses a MOSFET type too, but the manufacturer of theirs isn't on the RR itself. That makes identification nearly impossible.

Honda, Kawasaki and Yamaha all use Shindengen RRs in varying part or model numbers. These seem to range from an FH0001 to an FH0018A. The FH0001 can be found on R1s prior to 2006. It's huge though. The CBR/RR models use an FH0014A and the ZX6R an FH0016A. The most common ones used in the conversion are from either the R1 or the ZX10, that an FH0012A and an FH0010A respectively. There are others out there, including an FH0008A that I've seen available on Ebay. Any of these would be worth the $50-$70 asking price to do the conversion.

There is some conjecture on the web about the output amperage of these RRs. Some claim that the FH0012AA is 50A but some of the others to be at 35A. I read somewhere that Shindengen states they are 40 to 50A in all cases. Whether this is the case or not, I don't have any of these units in my hand with a test lead and my digital Voltmeter to test that claim. There are kits available now on Ebay also that include the RR and all the associated wiring, terminals and fitting to make the conversion work. Roadstercycle is the name of the site. Also, it was suggested that some sort of volt meter be added to the bike to monitor voltage being sent to the battery.

Further there is a company called Eastern Beaver that sells connector fittings and terminals. Some are packaged into kits also for just this job. Current models from the big 4 all have this type RR installed going back to 2006. Some going back to 2003 or 2004 depending on the model and manufacturer. I don't know about any of the Euro 4 doing the same. (BMW, Ducati, Aprilia and Triumph) Nothing I found during my research of this topic indicated that was the case. In fact, several forum articles I found indicated that this mod was being done on Triumphs, Aprilias and Ducatis. I don't know about BMW. I didn't see anything to indicate that.

The Stator (alternator in car lingo) creates an AC current by passing magnets over coils of wires while the engine is turning. The VR (Voltage Regulator) Regulates the voltage and to some degree the amperage created by the stator. It does this in order to not cook the battery. The faster the motor spins the more voltage it creates. Batteries shoul not be charged much higher than 14v. The stator without a regulator could run away to voltages of 24v+. Voltages higher than 14.5v will burn out a battery quickly. The shunt regulator basically shorts out all voltage over the limit of 14.5v which in some cases is shorting a lot of voltage and amperage to ground which creates a lot of heat. The Mosfets basically do the same thing but with more finess than brute force. They turn on and off several thousand times a second to keep the voltage steady. The Mosfets do not need as much power to operate and such can operate at lower rpms.

After your next ride, feel how hot your vr is. They get very warm if not hot. They are engineered just good enough for the heat they have to endure. The better way there is no significant heat therefore less stress and less possibility for failure. Its taking something that may very well break and replacing it with something that probably won't ever break. Less heat equals less stress in electronics.

RIDE REPORT 02/04/2015:

It finally was a nice day, so I put 160 miles on it today.

It worked perfectly, I did notice that the voltage was more constant, even at lower RPMS. Before the upgrade at low RPMs my voltage indicator would go from constant green, to blinking green, not anymore.

The unit itself was much cooler, than the OEM ever was.
Attached Images
File Type: jpg furukawa_3P-250_1028.jpg (30.8 KB, 7 views)
File Type: jpg 5P250-305K_1.jpg (8.3 KB, 377 views)
File Type: jpg FH012.jpg (30.0 KB, 9 views)
File Type: jpg 6107009945865934946.jpg (166.8 KB, 8 views)
File Type: pdf Wiring_Schematic_-_R4-2.pdf (373.7 KB, 4 views)
File Type: jpg VRegFH012.jpg (83.3 KB, 8 views)
File Type: jpg shindengen_fh012aa.jpg (129.6 KB, 4 views)
File Type: jpg 773789456_498.jpg (75.2 KB, 7 views)
File Type: jpg FH012-thermal.jpg (146.6 KB, 12 views)
File Type: jpg 6107253143648776594.jpg (88.1 KB, 144 views)
File Type: jpg 6107253163810458498.jpg (145.1 KB, 144 views)
Views 7778 Comments 2
Total Comments 2


  1. Old Comment
    Ghostt's Avatar
    Update: still waiting on my parts I ordered from Eastern Beaver, they did sent me an e-mail on December 12the saying the order was shipped,

    THANK YOU for the order from Eastern Beaver on Fri, 12 Dec 2014 20:14:01 -0800.
    Please see my Shipping Page if you have any questions about shipping.

    Jim Davis, Owner, Eastern Beaver Company: - Motorcycle Electrics
    Visit and like us on Facebook:
    Still haven't received items yet? Just wondering?

    ▼ Hide quoted text
    On Dec 15, 2014 8:57 PM, "Scott Ferguson" <> wrote:
    Thank you, I'll be waiting on it like a kid for Santa.

    Thank you,
    Scott Ferguson

    On Dec 15, 2014 8:45 PM, "Jim Davis" <> wrote:
    THANK YOU for the order from Eastern Beaver on Fri, 12 Dec 2014 20:14:01 -0800.
    Please see my Shipping Page if you have any questions about shipping.

    Jim Davis, Owner, Eastern Beaver Company: - Motorcycle Electrics
    Visit and like us on Facebook:

    but I have not received it yet, and have sent an e-mail.
    Posted December 22nd, 2014 at 08:58 PM by Ghostt Ghostt is offline

  2. Old Comment
    Ghostt's Avatar
    Update: parts from Eastern Beaver arrived yesterday, and as expected great packaging for shipping.

    stay tuned, hopefully I will get it completed in the next week or so.
    Posted December 25th, 2014 at 08:32 AM by Ghostt Ghostt is offline

Motorcycle Safety Foundation

All times are GMT -7. The time now is 07:51 AM.

Website uptime monitoring
Powered by vBulletin®
Copyright ©2000 - 2023, Jelsoft Enterprises Ltd.
User Alert System provided by Advanced User Tagging (Lite) - vBulletin Mods & Addons Copyright © 2023 DragonByte Technologies Ltd.
Except where otherwise noted, all site contents are © Copyright 2022, All rights reserved.