Forum: 2008 - 2012 Ninja 250R Tech Talk
April 18th, 2015, 09:58 AM
|
Replies: 49
Views: 5,031
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
April 17th, 2015, 10:38 AM
|
Replies: 49
Views: 5,031
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
April 17th, 2015, 09:01 AM
|
Replies: 49
Views: 5,031
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
April 17th, 2015, 08:17 AM
|
Replies: 49
Views: 5,031
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
April 16th, 2015, 07:55 PM
|
Replies: 49
Views: 5,031
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
April 12th, 2015, 09:51 AM
|
Replies: 49
Views: 5,031
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
April 11th, 2015, 10:21 AM
|
Replies: 49
Views: 5,031
Ok so I took off the air filter and found that...
Ok so I took off the air filter and found that the slides are indeed moving up and down. I must have been crazy because I also took out the needles and they appear straight, they obviously were not...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
April 11th, 2015, 09:00 AM
|
Replies: 49
Views: 5,031
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
April 10th, 2015, 09:00 PM
|
Replies: 49
Views: 5,031
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
April 10th, 2015, 06:08 PM
|
Replies: 49
Views: 5,031
I bought this bike "wrecked" (minor front end...
I bought this bike "wrecked" (minor front end <20mph) and have been rebuilding it. So I can't comment on the condition before I purchased it. The previous owner had done the slip on I added the pods...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
April 10th, 2015, 03:56 PM
|
Replies: 49
Views: 5,031
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
April 10th, 2015, 06:10 AM
|
Replies: 49
Views: 5,031
So it would appear that the pilots are...
So it would appear that the pilots are functioning normally, but for some reason there is an issue with the either the slides, diaphragm or main jets.
However I think I may have found another...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
April 9th, 2015, 04:42 PM
|
Replies: 49
Views: 5,031
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
April 9th, 2015, 08:59 AM
|
Replies: 49
Views: 5,031
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
April 9th, 2015, 08:37 AM
|
Replies: 49
Views: 5,031
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
April 9th, 2015, 08:19 AM
|
Replies: 49
Views: 5,031
Are you referring to the pilot screws or the...
Are you referring to the pilot screws or the mixture screw? I was under the assumption the pilot screw only effects the mixture at idle. Also the pilot screw is only accessible with the bowls off and...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
April 9th, 2015, 07:45 AM
|
Replies: 49
Views: 5,031
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
April 9th, 2015, 06:23 AM
|
Replies: 49
Views: 5,031
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
April 8th, 2015, 06:10 PM
|
Replies: 49
Views: 5,031
Alright here is a nightly report.
I...
Alright here is a nightly report.
I carefully went over the carbs again and here is what I did/found:
-Changed to #100 jet (#40 pilot) (Sorry DaBlue1, I am getting #105 tomorrow)
-Inspected...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
April 8th, 2015, 06:14 AM
|
Replies: 49
Views: 5,031
Alright, so your saying the jetting doesn't...
Alright, so your saying the jetting doesn't appear to be the problem. I'll go through and check everything else. I'll be honest, I have a sneaking suspicion the float level is too low. Using the tube...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
April 7th, 2015, 07:40 PM
|
Replies: 49
Views: 5,031
Need Assistance Tuning/Rejetting
So I began the process of re jetting my 2009 250 today to compensate for the slip-on and pod air filters. I'm having a fantastic time :roll eyes: . On the bright side, i'm a pro at removing the...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
April 3rd, 2015, 09:00 AM
|
Replies: 11
Views: 2,754
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
April 2nd, 2015, 06:38 AM
|
Replies: 11
Views: 2,754
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
April 2nd, 2015, 06:09 AM
|
Replies: 11
Views: 2,754
I use the choke until the bike is warm, but I...
I use the choke until the bike is warm, but I still experience the same thing.
So a lean condition could, in theory, result in the issues I'm experiencing? I just hate to spend $75 on jets, only...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
April 1st, 2015, 09:34 AM
|
Replies: 11
Views: 2,754
Lean Condition Causing Bike to Bog Down?
So long story short, my 2009 ninja 250 idles great but dies if I hit the throttle quick. If I slowly turn the throttle it usually makes it up to 4k rpm where it hesitates and bogs down. Occasionally...
|