Forum: 1986 - 2007 Ninja 250R Tech Talk
June 1st, 2016, 08:31 AM
|
Replies: 3
Views: 1,249
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
May 30th, 2016, 12:43 PM
|
Replies: 3
Views: 1,249
Sealing a tank to clean it out
I'm just wondering what those of you who have cleaned rust out of your tanks used to seal the holes for the petcock. The instructions I received with the por15 kit I bought said to use duct tape. It...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
November 22nd, 2015, 10:54 AM
|
Replies: 10
Views: 960
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
November 22nd, 2015, 10:15 AM
|
Replies: 10
Views: 960
It's the push/close cable. I don't know why I...
It's the push/close cable. I don't know why I didn't think about hooking the remaining cable up and seeing if it worked when it first happened. Do any of you ride around without a push cable? My...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
November 22nd, 2015, 10:03 AM
|
Replies: 10
Views: 960
Hmm Both of the cables are side by side on the...
Hmm Both of the cables are side by side on the bottom side of the grip. The cable that didn't break pulls up into the sheath when I roll the throttle back. I'm guessing that is the open cable. I've...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
November 22nd, 2015, 09:57 AM
|
Replies: 32
Views: 3,436
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
November 22nd, 2015, 09:36 AM
|
Replies: 10
Views: 960
|
Forum: Off-Topic
September 14th, 2015, 12:59 PM
|
Replies: 31
Views: 2,192
|
Forum: Off-Topic
September 14th, 2015, 12:17 PM
|
Replies: 31
Views: 2,192
|
Forum: Off-Topic
September 14th, 2015, 11:34 AM
|
Replies: 31
Views: 2,192
Returning to college as an adult
I've been trying to go back to school recently to finish a degree I started years ago. I went by the campus today to talk to an admissions adviser and it was a really uncomfortable experience. I got...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
September 13th, 2015, 03:58 AM
|
Replies: 10
Views: 3,719
Gas vent hose for carburetor
I replaced my carb not to long ago and the used carb I bought did not have a vent hose attached. Needless to say I need to buy another one. Can someone measure the inside diameter on theirs so I have...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
September 11th, 2013, 02:37 PM
|
Replies: 30
Views: 3,929
My seals looked the same, they didn't look like...
My seals looked the same, they didn't look like they would seal it but they did. It might be that the gasoline makes them swell. You could cut one of the old o-rings and measure the length, then find...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
September 11th, 2013, 02:16 PM
|
Replies: 30
Views: 3,929
I recently replaced the seals on my bowls and...
I recently replaced the seals on my bowls and they dont leak. Did you use the oem seals? Did you clean the surfaces thoroughly before installing them? I believe mine had some kind of sealer in them...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
September 11th, 2013, 01:30 PM
|
Replies: 30
Views: 3,929
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
September 11th, 2013, 11:28 AM
|
Replies: 9
Views: 1,368
I had this problem as well. The first owner let...
I had this problem as well. The first owner let the bike sit and the tank rusted out from the inside. It developed pin holes along the bottom side of the tank. I took it a radiator shop to have them...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
September 11th, 2013, 11:17 AM
|
Replies: 16
Views: 2,056
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
September 11th, 2013, 10:57 AM
|
Replies: 6
Views: 2,442
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
September 9th, 2013, 07:51 PM
|
Replies: 6
Views: 2,442
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
September 9th, 2013, 07:18 PM
|
Replies: 6
Views: 2,442
Pilot Jet screwdriver size
Does anybody know what size screwdriver fits? I used a 3/16 cabinet tip tonight like I did on my old carb and it damaged them while I was taking them off. I don't remember it damaging them when I...
|