Forum: 2008 - 2012 Ninja 250R Tech Talk
December 7th, 2018, 07:54 PM
|
Replies: 3
Views: 1,242
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
December 7th, 2018, 07:50 PM
|
Replies: 3
Views: 1,242
Front end lifting options
Hello all, hope everyone’s winter isn’t going by too slow. I had a question about lifting the front end for storage or in general. Well I currently have the bike lifted from the front under the...
|
Forum: General Motorcycling Discussion
December 5th, 2018, 08:29 PM
|
Replies: 8,589
Views: 1,093,270
|
Forum: Motorcycle-related
November 30th, 2018, 09:16 PM
|
Replies: 4
Views: 1,524
Great deal!! OP is not lying then he says the...
Great deal!! OP is not lying then he says the fairing and blinkers are a 2 beers job on a lazy afternoon. I know time can be limited by many reasons but you should put them on and sell the bike for...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
November 30th, 2018, 05:29 PM
|
Replies: 18
Views: 1,749
Thank you once again, everyone. I’ve acquired a...
Thank you once again, everyone. I’ve acquired a rear spool stand and I plan to use that with wood underneath the front tire. Now I don’t know if it’s reasonable to swap tires before I leave or wait...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
November 30th, 2018, 05:10 PM
|
Replies: 6
Views: 1,064
Tires
Hello all, this forum is awesome!!! I wanted to see what the opinions on tires were from some of the people on here.. I am new to motorcycling and would like to improve highway cruising capabilities...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
November 24th, 2018, 03:36 PM
|
Replies: 18
Views: 1,749
I agree it is too cold to ride, however I just...
I agree it is too cold to ride, however I just got my endorsement on November 3rd and the bike a couple days before so I am using any day above 45 degrees to ride short distances under 10 miles or...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
November 24th, 2018, 02:31 PM
|
Replies: 8
Views: 1,010
Okay cool, when the bike seems to be running...
Okay cool, when the bike seems to be running poorly again I will be sure to take out the carbs to clean them. Will try with one washer and rejet and possibly dyno etc. hopefully it can hold me until...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
November 24th, 2018, 02:09 PM
|
Replies: 8
Views: 1,010
Interesting, I appreciate you sharing your...
Interesting, I appreciate you sharing your knowledge! My question is, if I leave the shims in until my bike starts giving me problems again and then at that time thoroughly clean the carbs and remove...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
November 24th, 2018, 12:50 PM
|
Replies: 5
Views: 1,053
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
November 24th, 2018, 12:47 PM
|
Replies: 8
Views: 1,010
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
November 24th, 2018, 10:58 AM
|
Replies: 18
Views: 1,749
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
November 24th, 2018, 10:53 AM
|
Replies: 18
Views: 1,749
Everything is stock except,
shimming...
Everything is stock except,
shimming needles, snorkel delete, kn air filter and kleen air system delete.
It’s so cold out so I’m not able to test the bike fully..but starting it does require...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
November 24th, 2018, 08:53 AM
|
Replies: 18
Views: 1,749
If I remove a washer I think there’s a chance...
If I remove a washer I think there’s a chance it’ll be too lean, as I’m not overalls rich as is... do you think I can adjust the idle adjustment screws while the carbs are still in the bike? With...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
November 24th, 2018, 08:24 AM
|
Replies: 18
Views: 1,749
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
November 24th, 2018, 06:39 AM
|
Replies: 18
Views: 1,749
Running very slightly rich
Hello all, so I added 3 washers under each needle, kn filter with the snorkle delete. Bike seems much better day and night difference... my question is
Will removing the CAT in the exhaust help to...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
November 24th, 2018, 06:32 AM
|
Replies: 8
Views: 1,010
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
November 23rd, 2018, 10:27 AM
|
Replies: 8
Views: 1,010
Petcock plumbing
Hello all, I have researched and am pretty sure how the plumbing goes to the carbs...however I have a T connector which one end is going towards the front of the bike. I wanted to know how to connect...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
November 4th, 2018, 10:51 AM
|
Replies: 9
Views: 1,077
Thank you and thank you, I plan on taking the...
Thank you and thank you, I plan on taking the fairings off and possibly painting the bike but not until I put t least 1,000 miles on it. At that time I will change spark plugs oil and filter, and try...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
November 3rd, 2018, 06:53 PM
|
Replies: 5
Views: 1,053
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
November 3rd, 2018, 06:50 PM
|
Replies: 9
Views: 1,077
Hello all new here
Hey there everyone just picked up a 2010 250r 6,500 miles for $1,100... did I do well? I had a question what could this switch be for towards the front of the bike? Pretty sure it’s aftermarket.....
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
November 3rd, 2018, 06:45 PM
|
Replies: 5
Views: 1,053
Hello all
Just picked up a ninja 250r 2010 with 6,500 miles on it for $ 1,100... did I do well? Also I had a question about it
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
November 3rd, 2018, 06:21 PM
|
Replies: 20
Views: 2,121
|