Forum: 1986 - 2007 Ninja 250R Tech Talk
October 11th, 2023, 05:11 AM
|
Replies: 3
Views: 1,067
I just did mine with genuine Kawasaki parts. It...
I just did mine with genuine Kawasaki parts. It is a bit tricky alright but I just covered the groove in a diluted washing up liquid and worked it in. Getting your fingers inside helps to smooth it...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
October 5th, 2023, 01:35 AM
|
Replies: 16
Views: 2,443
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
October 3rd, 2023, 06:45 AM
|
Replies: 16
Views: 2,443
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
October 2nd, 2023, 09:27 AM
|
Replies: 391
Views: 67,882
Cleaned the carbs, reset float bowl height and...
Cleaned the carbs, reset float bowl height and replaced the rubbers between the airbox and the carbs. That last item made a great difference. The old rubbers didn't look too bad but the close fit of...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
October 2nd, 2023, 09:13 AM
|
Replies: 4
Views: 493
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
October 1st, 2023, 12:30 AM
|
Replies: 4
Views: 493
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
September 29th, 2023, 08:08 AM
|
Replies: 4
Views: 493
Do you know where this goes? (2004)
Hi all. I had reason to take the fuel tank off yesterday and noticed this cable guide just cable-tied to a the frame near the headstock. It obviously bolts on somewhere around there. Does anyone...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
November 24th, 2022, 04:22 PM
|
Replies: 2
Views: 428
Thanks Triple Jim. Tank vent clear and I have...
Thanks Triple Jim. Tank vent clear and I have replaced the little fuel filter with an external filter. Pretty convinced it is not fuel now, I have been right through that system.
Good idea about...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
November 24th, 2022, 03:03 PM
|
Replies: 2
Views: 428
2004 breaks down but 45-60 minutes in to the ride
2004 running just fine in every respect. A really clean example with 6,000 miles on it and stored inside most of its life by the look of it. Electrical connections and cables are clean everywhere.
...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
August 22nd, 2022, 04:02 AM
|
Replies: 5
Views: 592
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
August 19th, 2022, 07:08 AM
|
Replies: 5
Views: 548
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
August 19th, 2022, 04:46 AM
|
Replies: 5
Views: 548
Cable snagged
You were right Patrizio. After taking all the bodywork off to adjust the valve clearances I got a clearer view of the throttle cabling. One of the cables lock-nuts on the adjuster was loose,...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
August 16th, 2022, 11:53 AM
|
Replies: 10
Views: 1,015
Valve Clearances at 5,700miles on a 2004.
A very low mileage 2004 with a verified 5,700 miles. All exhaust valves overtight and all intakes within spec but at the lower end. This is its first valve check. Given the exhaust side all being out...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
August 15th, 2022, 02:21 AM
|
Replies: 5
Views: 548
Idle not stable - carb issues?
My 2004 starts easily and runs well at speed and at normal temperature but it does have an idling problem. It starts on choke and if you leave it to warm up will eventually idle at 1200-1300 RPM...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
August 15th, 2022, 02:01 AM
|
Replies: 10
Views: 1,015
|
Forum: Pictures
August 14th, 2022, 08:14 AM
|
Replies: 2,623
Views: 528,177
This just joined the family
A 2004 in great condition joins the family. It has just replaced a 2021 Honda CB125F so the jump in power is very welcome.
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
August 14th, 2022, 07:13 AM
|
Replies: 10
Views: 1,015
|
Forum: New Members
August 14th, 2022, 06:50 AM
|
Replies: 5
Views: 447
Hi from Ireland
Hi there - Picked up a smashing 2004 Ninja 250 USA Import here in Ireland. Full disclosure, I am the owners Dad and it will be me maintaining it and reading these pages. He's too busy with just using...
|