Forum: 1986 - 2007 Ninja 250R Tech Talk
May 5th, 2013, 05:36 AM
|
Replies: 40
Views: 12,017
el250 engine
Did you swap over the 1986-1987 EX250E stator rotor onto the EL250 engine?
You need to and also use its two pulsing coil pickups instead of the newer single coil pickup (found on the EL250B/E and...
|
Forum: Motorcycle-related
September 1st, 2012, 01:09 AM
|
Replies: 170
Views: 19,201
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
March 20th, 2012, 04:57 PM
|
Replies: 12
Views: 1,316
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
March 20th, 2012, 04:38 PM
|
Replies: 12
Views: 1,316
Just to clarify, I only pulled out that...
Just to clarify, I only pulled out that black/white wire because it was just random chance to be where I pushed in the screwdriver for the example.
You need to pull out and move:
Red/Yellow...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
March 20th, 2012, 04:29 PM
|
Replies: 12
Views: 1,316
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
March 17th, 2012, 05:03 PM
|
Replies: 12
Views: 1,316
re-pin your left hand switch connector
You need to re-pin the LH Switch connector to match the wiring of your harness.
The 1994 and years before use the old left hand switch control that was used on older models.
It has an extra wire...
|
Forum: General Motorcycling Discussion
March 17th, 2012, 01:09 PM
|
Replies: 10
Views: 1,353
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
March 15th, 2012, 12:08 AM
|
Replies: 331
Views: 144,137
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
March 14th, 2012, 11:32 PM
|
Replies: 331
Views: 144,137
Hello Richard?,...
Hello Richard?, http://twostrokemotocross.com/2011/09/ditching-your-two-strokes-carb-for-port-fuel-injection/
Is this the same Richard of High Gain Antenna that was in the news years back for...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
February 29th, 2012, 01:57 PM
|
Replies: 49
Views: 5,267
|
Forum: Motorcycle-related
January 10th, 2012, 11:28 PM
|
Replies: 874
Views: 127,893
I don't think the ecotrons ECU cares about the...
I don't think the ecotrons ECU cares about the safety switches and does not have anti-hotwire. So those wires are not used (Green/Blue and Gray) and no need for resistor for 1988-1994 bikes.
It...
|
Forum: Motorcycle-related
January 10th, 2012, 10:54 PM
|
Replies: 874
Views: 127,893
Is the pinning like this: ...
Is the pinning like this:
http://s13.postimage.org/ykid73bn9/pinview.png
ecotrons wiring -> main wiring harness color 1988-1994 (1995-2007)
keysw +12vdc:
pink -> red (brown/black)
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
January 10th, 2012, 09:57 PM
|
Replies: 8
Views: 7,077
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
December 22nd, 2011, 09:34 AM
|
Replies: 12
Views: 2,230
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
December 22nd, 2011, 08:55 AM
|
Replies: 12
Views: 2,230
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
December 20th, 2011, 08:41 AM
|
Replies: 8
Views: 7,077
|
Forum: Motorcycle-related
December 19th, 2011, 05:45 PM
|
Replies: 874
Views: 127,893
He might be in MI, but I find Xinhua District,...
He might be in MI, but I find Xinhua District, Shijiazhuang China. It is no problem and looks like a good kit, just trying to make sense of things.
I might be interested in the kit but without...
|
Forum: Motorcycle-related
December 19th, 2011, 03:52 PM
|
Replies: 874
Views: 127,893
Carb heating:
None had it in North America,...
Carb heating:
None had it in North America, only in UK/Europe, Australia, or Japan spec -F but mostly -H models, as seen in instructions, and any of those as grey market bikes imported elsewhere.
...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
December 10th, 2011, 06:30 AM
|
Replies: 18
Views: 2,625
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
December 10th, 2011, 04:49 AM
|
Replies: 331
Views: 144,137
Eat288
EAT288 are made by Denso (formly known as NipponDenso) and have the NipponDenso / Sumitomo type connector.
The ECU is by Denso so makes sense.
They are not Keihin because they would have the...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
December 9th, 2011, 09:32 AM
|
Replies: 10
Views: 1,569
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
December 8th, 2011, 09:56 AM
|
Replies: 331
Views: 144,137
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
December 8th, 2011, 05:12 AM
|
Replies: 12
Views: 1,609
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
December 8th, 2011, 01:55 AM
|
Replies: 12
Views: 1,609
The stud mounts are not through drilled into...
The stud mounts are not through drilled into water jacket or into the valve train area where oil is. Maybe you have a crack inside your mount?
The 1986-1987 did only have two mounts per exhaust...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
December 8th, 2011, 01:33 AM
|
Replies: 11
Views: 1,133
|