ninjette.org

Go Back   ninjette.org > Search Forums

Showing results 1 to 17 of 17
Search took 0.00 seconds.
Search: Posts Made By: Kasatka
Forum: 2008 - 2012 Ninja 250R Tech Talk August 21st, 2015, 04:07 PM
Replies: 1,732
Views: 180,708
Posted By Kasatka
I'm having a hell of a time figuring that out. I...

I'm having a hell of a time figuring that out. I think I may see that it recorded a map error of some kind, but could be wrong. Can anyone help interpret whether it's cutting off between the hot and...
Forum: 2008 - 2012 Ninja 250R Tech Talk July 2nd, 2015, 10:12 AM
Replies: 1,732
Views: 180,708
Posted By Kasatka
What value in procal do I need to check for that...

What value in procal do I need to check for that info?

When adjusting the air screws, fLc and fLc2 stayed around .75 pretty consistently, and uLsb and uLsb2 stayed higher than .45V.

Edit: It is...
Forum: 2008 - 2012 Ninja 250R Tech Talk July 2nd, 2015, 09:14 AM
Replies: 1,732
Views: 180,708
Posted By Kasatka
Updates on my kit problem: I fiddled with the...

Updates on my kit problem: I fiddled with the idle air screws and procal. At 3.5 turns out, it seemed like I'd fixed the problem; when I test drove it around the block for 20 minutes it didn't bog...
Forum: 2008 - 2012 Ninja 250R Tech Talk April 18th, 2015, 05:19 PM
Replies: 1,732
Views: 180,708
Posted By Kasatka
Did another test ride. The bike wouldn't start at...

Did another test ride. The bike wouldn't start at all, until I switched it to rich mode. Then it started after 8 or 9 seconds of cranking. I tried putting the laptop in a backpack to record procal...
Forum: 2008 - 2012 Ninja 250R Tech Talk April 18th, 2015, 03:55 PM
Replies: 1,732
Views: 180,708
Posted By Kasatka
I've been messing around in ProCAL looking for...

I've been messing around in ProCAL looking for the value you changed and I'm not sure which one it is. I see one described as the "offset for manifold pressure sensor characteristics" and one as the...
Forum: 2008 - 2012 Ninja 250R Tech Talk April 1st, 2015, 07:19 PM
Replies: 1,732
Views: 180,708
Posted By Kasatka
Yep, it is in ECO mode. I'll check the vacuum...

Yep, it is in ECO mode. I'll check the vacuum hoses tomorrow.



Thanks, I'll give that a shot. The language barrier is pretty frustrating... I know it's really hard to learn a second language...
Forum: 2008 - 2012 Ninja 250R Tech Talk April 1st, 2015, 04:23 PM
Replies: 1,732
Views: 180,708
Posted By Kasatka
I'll give that a shot. Other than this kit, I...

I'll give that a shot. Other than this kit, I haven't modded the bike at all. All original equipment.

Edit: Holy god. Went out, key on, disconnected computer, wait 5 seconds, reconnected, key off....
Forum: 2008 - 2012 Ninja 250R Tech Talk April 1st, 2015, 03:05 PM
Replies: 1,732
Views: 180,708
Posted By Kasatka
I had been running it in ECO mode from the...

I had been running it in ECO mode from the beginning. I only switched it to Rich mode briefly for two test rides, and that was after it started dying every time I took it out. It's now in ECO mode,...
Forum: 2008 - 2012 Ninja 250R Tech Talk April 1st, 2015, 02:42 PM
Replies: 1,732
Views: 180,708
Posted By Kasatka
Got a response from Ecotrons, but I'm having...

Got a response from Ecotrons, but I'm having trouble understanding what they're saying.

"Yes, you recorded the data very clear, and the problem is very obvious.

First, before you switch the...
Forum: 2008 - 2012 Ninja 250R Tech Talk March 28th, 2015, 12:46 PM
Replies: 1,732
Views: 180,708
Posted By Kasatka
Ecotrons asked for a recording from cold startup...

Ecotrons asked for a recording from cold startup through it cutting out, but it doesn't cut out until it gets hot under load, and I can't hold a laptop while I ride.
Forum: 2008 - 2012 Ninja 250R Tech Talk March 28th, 2015, 11:58 AM
Replies: 1,732
Views: 180,708
Posted By Kasatka
Still doing it. I can't take the bike anywhere...

Still doing it. I can't take the bike anywhere when it suddenly stops running at warmup. I didn't change anything before it stopped working, and it only cuts out under load so I can't record data...
Forum: 2008 - 2012 Ninja 250R Tech Talk March 2nd, 2015, 08:25 PM
Replies: 1,732
Views: 180,708
Posted By Kasatka
Just emailed them today, with Procal data. The...

Just emailed them today, with Procal data. The lines have pressure on startup but I'll check while it stalls. The fuel filter is half full all the time.

The only thing that changed between when...
Forum: 2008 - 2012 Ninja 250R Tech Talk March 2nd, 2015, 04:54 PM
Replies: 1,732
Views: 180,708
Posted By Kasatka
I've got the Ecotrons EFI kit installed on my 99...

I've got the Ecotrons EFI kit installed on my 99 Ninja 250. When I first got it installed, for half a dozen rides it started up and ran great. Then for 3 or 4 rides it started up and ran fine until...
Forum: 1986 - 2007 Ninja 250R Tech Talk February 16th, 2015, 02:26 PM
Replies: 106
Views: 66,336
Posted By Kasatka
I'm not sure if this is a good place for this;...

I'm not sure if this is a good place for this; let me know if it'd be better put in another thread.

I've got the Ecotrons EFI kit installed on my 99 Ninja 250. When I first got it installed, for...
Forum: Motorcycle-related September 2nd, 2014, 06:03 PM
Replies: 94
Views: 10,393
Posted By Kasatka
I emailed Ecotrons, and they're still offering...

I emailed Ecotrons, and they're still offering 10% off each kit if 2 or more kits are bought together. Is anyone else interested in buying this kit soon, who'd like to do a "group" buy with me and...
Forum: Motorcycle-related August 28th, 2014, 09:55 AM
Replies: 94
Views: 10,393
Posted By Kasatka
Shortly as in less than a couple weeks? I'd like...

Shortly as in less than a couple weeks? I'd like to get the conversion done before the weather gets too cold. Are you gonna have links to the parts or a kit in your write up?
Forum: Motorcycle-related August 21st, 2014, 07:07 PM
Replies: 94
Views: 10,393
Posted By Kasatka
Dunno if it's too late, but I'm interested in...

Dunno if it's too late, but I'm interested in getting the EFI kit.
Showing results 1 to 17 of 17

 
Forum Jump




Motorcycle Safety Foundation

All times are GMT -7. The time now is 11:54 PM.


Website uptime monitoring Host-tracker.com
Powered by vBulletin®
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
User Alert System provided by Advanced User Tagging (Lite) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
Except where otherwise noted, all site contents are © Copyright 2022 ninjette.org, All rights reserved.