Forum: 1986 - 2007 Ninja 250R Tech Talk
March 24th, 2024, 07:49 PM
|
Replies: 3
Views: 159
|
Forum: New Members
March 24th, 2024, 07:44 PM
|
Replies: 4
Views: 115
|
Forum: New Members
March 23rd, 2024, 07:24 PM
|
Replies: 4
Views: 355
|
Forum: New Members
March 18th, 2024, 05:02 AM
|
Replies: 3
Views: 147
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
March 17th, 2024, 07:34 PM
|
Replies: 371
Views: 66,219
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
March 16th, 2024, 03:46 PM
|
Replies: 7
Views: 222
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
March 16th, 2024, 03:01 PM
|
Replies: 7
Views: 222
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
March 16th, 2024, 01:39 PM
|
Replies: 7
Views: 222
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
March 16th, 2024, 12:49 PM
|
Replies: 7
Views: 222
Don't use starting fluid unless you want to...
Don't use starting fluid unless you want to replace the diaphragms again. :)
I'm wondering if something is wrong with the petcock, and it's not fully opening during cranking when vacuum is low. ...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
March 16th, 2024, 05:52 AM
|
Replies: 10
Views: 278
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
March 15th, 2024, 02:41 PM
|
Replies: 10
Views: 278
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
March 15th, 2024, 01:02 PM
|
Replies: 10
Views: 278
There is a small fuel filter where the hose...
There is a small fuel filter where the hose enters the carb. Sometimes it gets very clogged, and is jammed up the hose so you don't immediately see it. Even if this isn't the problem it's something...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
March 15th, 2024, 09:21 AM
|
Replies: 4
Views: 193
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
March 15th, 2024, 05:31 AM
|
Replies: 4
Views: 193
They need to be set for highest idle speed. ...
They need to be set for highest idle speed. Erring a tiny bit on the rich side is better than on the lean side. ducatiman may have some additional relevant advice.
Why did you clean new OEM...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
March 15th, 2024, 05:28 AM
|
Replies: 1
Views: 130
|
Forum: New Members
March 14th, 2024, 05:44 AM
|
Replies: 5
Views: 200
|
Forum: New Members
March 13th, 2024, 04:28 PM
|
Replies: 5
Views: 200
Hey Jacob, welcome! I have a 2005 myself. Good...
Hey Jacob, welcome! I have a 2005 myself. Good luck with the valve adjustment. When I did mine it ran like it had a new engine compared to before the adjustment. Starting and warmup was hugely...
|
Forum: New Members
March 9th, 2024, 05:52 AM
|
Replies: 10
Views: 280
|
Forum: Ninjettes At Speed
March 6th, 2024, 08:49 AM
|
Replies: 11
Views: 3,719
Depending on what aluminum alloy it is, an...
Depending on what aluminum alloy it is, an aluminum rear sprocket can last a long time in street use. I put 30,000 miles on one that still shows nearly no wear. I do keep my chain lubed properly.
|
Forum: Ninjettes At Speed
March 5th, 2024, 01:14 PM
|
Replies: 4
Views: 1,180
|
Forum: Ride Reports
March 3rd, 2024, 09:53 AM
|
Replies: 21
Views: 1,723
|
Forum: Ride Reports
March 3rd, 2024, 06:01 AM
|
Replies: 21
Views: 1,723
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
March 2nd, 2024, 06:25 AM
|
Replies: 3
Views: 590
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
March 1st, 2024, 05:01 PM
|
Replies: 3
Views: 590
I'm not sure what you mean. My '05 250 has a...
I'm not sure what you mean. My '05 250 has a steel frame, and a magnet sticks to it. As a rule, steels are alloys of iron and other things like carbon, chromium, vanadium, nickel, etc. Steels like...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
March 1st, 2024, 05:37 AM
|
Replies: 4
Views: 1,577
|