Forum: 1986 - 2007 Ninja 250R Tech Talk
August 30th, 2022, 05:14 AM
|
Replies: 176
Views: 10,961
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
August 22nd, 2022, 02:04 PM
|
Replies: 176
Views: 10,961
I forgot the tank had rust in it so I couldn't...
I forgot the tank had rust in it so I couldn't use it to try to start the bike. I'm going to go this route (https://www.hondarebelforum.com/threads/tank-cleaning.7168/) again and just do multiple...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
August 12th, 2022, 02:03 PM
|
Replies: 176
Views: 10,961
DannoXYZ
All the plastics have been...
DannoXYZ
All the plastics have been repaired, but not painted. Had to add some raw plastic strips in for support on the middle of the lower cowl, it was cracked in half at the bushing spot.
...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
July 15th, 2022, 11:21 AM
|
Replies: 176
Views: 10,961
reassembled front caliper. trying to bleed the...
reassembled front caliper. trying to bleed the rear one but the bleeder screw is entirely rusted through. ordering a new one, looks to me m7x1, 26mm length.
also picking up allen bolts for the front...
|
Forum: Off-Topic
July 13th, 2022, 04:16 PM
|
Replies: 32
Views: 1,803
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
July 13th, 2022, 01:27 PM
|
Replies: 176
Views: 10,961
Mounted tire on wheel today. I have some white...
Mounted tire on wheel today. I have some white ceramic beads I put in the valve stem. https://www.kawasa***************/threads/tire-balancing-beads.36721/ (ninja300 forum) says 1oz in front and 2oz...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
February 8th, 2022, 09:29 PM
|
Replies: 176
Views: 10,961
|
Forum: Forum Information
December 2nd, 2021, 07:15 PM
|
Replies: 2,694
Views: 569,148
|
Forum: Forum Information
November 10th, 2021, 05:14 PM
|
Replies: 2,694
Views: 569,148
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
November 7th, 2021, 02:32 PM
|
Replies: 176
Views: 10,961
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
November 1st, 2021, 07:03 AM
|
Replies: 176
Views: 10,961
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
November 1st, 2021, 12:58 AM
|
Replies: 176
Views: 10,961
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
October 31st, 2021, 04:58 PM
|
Replies: 176
Views: 10,961
oooohhhh yeah the ABS im trying to melt is all...
oooohhhh yeah the ABS im trying to melt is all coloured. I tried fairing material before and it mostly dissolved, but still not like it was supposed to. I'll post ABS and acetone and container that...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
October 31st, 2021, 12:29 PM
|
Replies: 176
Views: 10,961
I've been trying to dissolve ABS pellets in...
I've been trying to dissolve ABS pellets in acetone for a few days now, but it doesn't seem like it's dissolving like it's supposed to, or mixing with the acetone like it's supposed to. At the bottom...
|
Forum: General Motorcycling Discussion
October 31st, 2021, 02:52 AM
|
Replies: 24
Views: 2,032
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
October 29th, 2021, 06:37 PM
|
Replies: 176
Views: 10,961
Cleaned it up. The melty temperature was a lot...
Cleaned it up. The melty temperature was a lot easier to figure out this time. It's just not sticking how I want it to. Might need to buy actual flux, might not be the right aluminum, could be the...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
October 29th, 2021, 05:59 PM
|
Replies: 176
Views: 10,961
Weld stuck until I tried to take it out of the...
Weld stuck until I tried to take it out of the vice and wiggle it, then same thing happened where it just didn't stick to the aluminum. Takes a lot of heat and the point between the stick melting and...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
October 28th, 2021, 08:42 PM
|
Replies: 176
Views: 10,961
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
October 28th, 2021, 07:44 PM
|
Replies: 176
Views: 10,961
I didn't realize aluminum brazing/welding was...
I didn't realize aluminum brazing/welding was different than other metals. guess that's where experience comes in.
sorry danno, it's the front peg, not the rear. the angle is different (and length...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
October 24th, 2021, 04:49 PM
|
Replies: 176
Views: 10,961
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
October 24th, 2021, 12:39 PM
|
Replies: 176
Views: 10,961
|
Forum: Riding Skills
October 21st, 2021, 09:11 AM
|
Replies: 21
Views: 3,438
|
Forum: General Motorcycling Discussion
October 21st, 2021, 12:19 AM
|
Replies: 292
Views: 15,321
Make sure to not compress the shocks too much,...
Make sure to not compress the shocks too much, you can blow the seals on bumps if you do. More tie-down strength /= more better.
Tightened mine 1mi after, 5mi after, then checked it three more...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
October 19th, 2021, 08:13 PM
|
Replies: 176
Views: 10,961
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
October 19th, 2021, 08:06 PM
|
Replies: 176
Views: 10,961
|