Forum: 1986 - 2007 Ninja 250R Tech Talk
December 23rd, 2013, 03:19 PM
|
Replies: 9
Views: 2,352
It's ok. I'm just unable to tear into it and...
It's ok. I'm just unable to tear into it and troubleshoot. I live where it can't be left torn down & a pain in the arse to reassemble everything after trying one thing. I learned a LOT about...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
December 23rd, 2013, 01:57 PM
|
Replies: 9
Views: 2,352
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
December 1st, 2013, 05:01 PM
|
Replies: 4
Views: 1,920
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
December 1st, 2013, 04:38 PM
|
Replies: 4
Views: 1,920
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
December 1st, 2013, 04:09 PM
|
Replies: 4
Views: 1,920
CDI Ignitor compatibility between years
In the process of finding why the Ninja isn't running, I arced the spark plug to the frame and it has spark- just not a powerful one. The spark plugs are brand new NGK CR8HSA, but the coil wires both...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
December 1st, 2013, 01:37 AM
|
Replies: 9
Views: 2,352
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
December 1st, 2013, 01:32 AM
|
Replies: 9
Views: 2,352
The thing is that I had it started last week...
The thing is that I had it started last week until it ran out of gas (the fuel line wasn't hooked up), but when I connect the fuel line it overflows gas and won't start.
I pulled the carb again and...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
November 29th, 2013, 10:56 PM
|
Replies: 9
Views: 2,352
Vacuum hose cross caused leak
Now that my car is totaled, I only have this bike that's been sitting for a couple years to get me around- but paying to have it repaired was out of my realm of possibilities. So, I did my first carb...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
August 25th, 2013, 09:19 PM
|
Replies: 2
Views: 660
Can't find o-ring to fit drain screw
I finally got the bike to start and run, but there is a steady leak from one of my float bowl drains. The tip of the drain screw had corroded away, so I ordered another drain screw- but it doesn't...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
August 24th, 2013, 05:32 PM
|
Replies: 4
Views: 1,683
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
August 24th, 2013, 04:40 PM
|
Replies: 4
Views: 1,683
Only runs on starting fluid
I've done everything I could think of to get this bike running the past few weeks. A quick explanation of what happened-
Three years ago, I was enjoying a ride when I ran out of gas. I hadn't used...
|
Forum: 1986 - 2007 Ninja 250R Farkles
August 12th, 2013, 04:44 PM
|
Replies: 41
Views: 42,019
|
Forum: 1986 - 2007 Ninja 250R Farkles
August 11th, 2013, 12:31 PM
|
Replies: 41
Views: 42,019
|
Forum: 1986 - 2007 Ninja 250R Farkles
July 28th, 2013, 06:55 PM
|
Replies: 7
Views: 981
rear view mirrors/turn signals
I have a 1993 pregen that I would like to do some custom work on the fairings. One of the mods is filling in the turn signal and headlight openings. I found some videos on doing the headlight...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
July 28th, 2013, 12:35 AM
|
Replies: 10
Views: 1,108
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
July 27th, 2013, 10:18 PM
|
Replies: 10
Views: 1,108
|
Forum: New Members
July 26th, 2013, 09:39 PM
|
Replies: 11
Views: 773
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
July 26th, 2013, 09:24 PM
|
Replies: 10
Views: 1,108
Thanks for the answers. I'll swap the carbs out...
Thanks for the answers. I'll swap the carbs out and practice rebuilding the old set. Kind of takes the stress off of not messing up my only set. I've found some good tutorials & kind of eager to try...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
July 26th, 2013, 07:44 PM
|
Replies: 10
Views: 1,108
Time to start the huge task of repairs
About three years ago, my Ninja 250 finally succumbed to the rust in its tank. There is a pin-hole leak right behind the top fairing bolt (I learned there are two sizes of fairing bolts.... the hard...
|
Forum: New Members
July 26th, 2013, 07:23 PM
|
Replies: 11
Views: 773
Hello from Port Orchard. WA!!!!!!
I have had my 1993 Ninja 250 for many years, but now it needs a lot of attention & I came here to learn all your pearls of wisdom (& perhaps share some of my own). Looking forward to being a part of...
|