ninjette.org

Go Back   ninjette.org > Search Forums

Showing results 1 to 9 of 9
Search took 0.00 seconds.
Search: Posts Made By: hillbilly86
Forum: General Motorcycling Discussion June 4th, 2013, 08:39 PM
Replies: 26
Views: 2,696
Posted By hillbilly86
well the gravel is where it finally laid down, it...

well the gravel is where it finally laid down, it started in the grass haha. I'll rev it up and pop the clutch in the gravel all the time, but I forgot that grass, a slick rear tire, and popping the...
Forum: General Motorcycling Discussion June 4th, 2013, 08:34 PM
Replies: 8,589
Views: 1,082,905
Posted By hillbilly86
Laid my bike down in my driveway acting like a...

Laid my bike down in my driveway acting like a retard. Reminder, slick tires, grass, and popping the clutch don't mix too well. Now I have a reason to finish up the little bit of bondo work I need to...
Forum: General Motorcycling Discussion June 4th, 2013, 08:19 PM
Replies: 26
Views: 2,696
Posted By hillbilly86
just pay attention to what you're doing and don't...

just pay attention to what you're doing and don't get too ballsy, I laid my bike down in my driveway today goofing off as I was pulling in on the gravel. Don't get stupid and you should be good to go
Forum: General Motorcycling Discussion June 4th, 2013, 07:00 PM
Replies: 15
Views: 3,043
Posted By hillbilly86
Finally got her running right. After adjusting...

Finally got her running right. After adjusting the air/fuel mixture with no change I reluctantly pulled the carbs to check the adjustments on the floats. Notice the float on the right side (which...
Forum: General Motorcycling Discussion June 4th, 2013, 11:18 AM
Replies: 15
Views: 3,043
Posted By hillbilly86
thank you sooo much, I'm trying what I can...

thank you sooo much, I'm trying what I can without having to pull the carbs again so if this doesn't do it then my next step will be checking the floats and adjust if necessary. I'll keep ya updated
Forum: General Motorcycling Discussion June 4th, 2013, 11:15 AM
Replies: 15
Views: 3,043
Posted By hillbilly86
chopped the cans in half, drilled out the rivets...

chopped the cans in half, drilled out the rivets on the back plate so I could just remove the baffling but the plate is connected to the small pipe running thru so I chopped them down, figured if I...
Forum: General Motorcycling Discussion June 4th, 2013, 10:36 AM
Replies: 15
Views: 3,043
Posted By hillbilly86
I've not done any mods on the bike other than...

I've not done any mods on the bike other than chopping up the stock exhaust (just because I don't have $396 to spend on slip-ons), I happen to notice today the the diaphragm on the right side of the...
Forum: General Motorcycling Discussion June 3rd, 2013, 07:34 PM
Replies: 17
Views: 4,168
Posted By hillbilly86
I went with flat black on mine, but I'm not too...

I went with flat black on mine, but I'm not too big on "standing out". When I bought my bike there were actually 2 red led strips on either side facing the engine, so I moved them to the front and...
Forum: General Motorcycling Discussion June 3rd, 2013, 07:15 PM
Replies: 15
Views: 3,043
Posted By hillbilly86
Running rich, any help?

I'm new to the forum. I've got a 1990 ninja 250, idled and ran fine, then I removed all the plastics to paint them and after putting it all together it suddenly started running rich and flooding...
Showing results 1 to 9 of 9

 
Forum Jump




Motorcycle Safety Foundation

All times are GMT -7. The time now is 08:40 AM.


Website uptime monitoring Host-tracker.com
Powered by vBulletin®
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
User Alert System provided by Advanced User Tagging (Lite) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
Except where otherwise noted, all site contents are © Copyright 2022 ninjette.org, All rights reserved.