Forum: 2008 - 2012 Ninja 250R Tech Talk
September 30th, 2019, 05:37 AM
|
Replies: 10
Views: 917
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
September 28th, 2019, 03:52 PM
|
Replies: 10
Views: 917
Thanks for all the suggestions...
I have a...
Thanks for all the suggestions...
I have a Battery Charger/Engine Starter for a car. Is that safe to use on it?
Also, I put the new battery on the tinder and let it sit through several cycles....
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
September 28th, 2019, 10:07 AM
|
Replies: 10
Views: 917
Starting problems
This may be similar to https://www.ninjette.org/forums/showthread.php?t=336642&highlight=starter, but I am not sure.
Basically, I went out to startup my 2008 250r and it would not even crank (been...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
February 17th, 2019, 06:38 PM
|
Replies: 2
Views: 703
Replacing turn signal switch 2008 250R
My turn signals are intermittently not working. Turn on the switch and they may/may not work, AND it is getting worse. Someone in another thread mentioned corrosion in the switch and bulb housings....
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
October 3rd, 2018, 08:08 AM
|
Replies: 27
Views: 2,177
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
September 29th, 2018, 11:39 AM
|
Replies: 27
Views: 2,177
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
September 29th, 2018, 10:39 AM
|
Replies: 27
Views: 2,177
Question about torque specs
I recently changed my oil and the service manual says to torque the filter cover and plug to 14.5 ft/lbs of torque. However, it was getting so tight, that the bike was moving and I was not hearing...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
May 28th, 2018, 08:28 PM
|
Replies: 8
Views: 965
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
May 28th, 2018, 07:26 PM
|
Replies: 8
Views: 965
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
May 28th, 2018, 06:37 PM
|
Replies: 8
Views: 965
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
May 28th, 2018, 04:38 PM
|
Replies: 8
Views: 965
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
May 28th, 2018, 03:14 PM
|
Replies: 8
Views: 965
Frozen rotor bolts
I am having to replace my rotors on my 250R. I am the 3rd owner, so I don't know what was done before. However, the rotor bolts are frozen (or stuck) and I am not able to break them loose. Also, I...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
March 25th, 2018, 07:46 PM
|
Replies: 3
Views: 763
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
March 25th, 2018, 12:08 PM
|
Replies: 3
Views: 763
Strange turn-signal problem
So, been noticing that occasionally my turn signals just randomly stop working while riding. If I leave the switch on as though I am indicating a turn, most of the time the come back some time later...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
March 19th, 2018, 01:34 PM
|
Replies: 6
Views: 1,004
Speedo wrong reading
I have an '08 250R and noticed that when I get above about 30mph, the speedo is incorrect at what I am traveling by about +5mph. My son was noticing that he was following me at around 40mph, while...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
September 26th, 2017, 01:46 PM
|
Replies: 20
Views: 5,873
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
September 26th, 2017, 12:00 PM
|
Replies: 20
Views: 5,873
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
September 5th, 2017, 09:31 AM
|
Replies: 2
Views: 980
2008 Ninja 205R shifter position
So, after changing my sprocket and chain, I have my bike in nice working order. However, the shifter seems a bit too high (too much clearance between my foot and the shifter). I am a relatively new...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
August 5th, 2017, 10:20 PM
|
Replies: 20
Views: 5,873
Thanks everyone for replying. I know for sure...
Thanks everyone for replying. I know for sure that one of the bolts broke off - how far into the threaded hole, I have no idea because I think I broke 2 and can't seem to back-out the other one I...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
August 5th, 2017, 07:26 PM
|
Replies: 20
Views: 5,873
Broken sprocket cover bolts
Stupid me! When I read the maintenance manual on my 2008 250R, I mis-read the torque specs for the engine sprocket cover bolts. They are supposed to be 87 ft-in, but I read it as 87 ft-lbs. Now, I...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
August 5th, 2017, 07:24 PM
|
Replies: 39
Views: 3,977
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
August 1st, 2017, 04:49 PM
|
Replies: 6
Views: 2,406
Awesome! The manual states "Apply molybdenum...
Awesome! The manual states "Apply molybdenum disulfide oil solution. (mixture of engine oil and molybdenum disulfide grease
in a weight ratio 10 : 1)."
Does this mean 10 parts oil to 1 part...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
August 1st, 2017, 02:36 PM
|
Replies: 6
Views: 2,406
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
August 1st, 2017, 02:11 PM
|
Replies: 6
Views: 2,406
molybdenum disulfide oil solution???
So, it turns out my front sprocket is toast (literally no teeth left). I ordered a new one, but the service manual mentions applying molybdenum disulfide oil solution to the sprocket. I have some...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
July 28th, 2017, 05:46 PM
|
Replies: 39
Views: 3,977
So, it DOES look like it is the chain. There is...
So, it DOES look like it is the chain. There is practically NO teeth left on the front-sprocket. I purchased one on eBay that says it would fit a 2008 250R, but alas it doesn't (the inner teeth on...
|