ninjette.org

Go Back   ninjette.org > Search Forums
Reload this Page Search Results
Portal Page Forums NinjetteWiki Blogs Register FAQ Today's Posts Search

Page 1 of 2 1 2
Showing results 1 to 25 of 28
Search took 0.00 seconds. Search: Posts Made By: Ragnar1x
Forum: 1986 - 2007 Ninja 250R Tech Talk May 22nd, 2011, 09:28 AM
Replies: 45
Views: 5,876
Posted By Ragnar1x
Resynced the carbs and further adjusted the idle...

Resynced the carbs and further adjusted the idle mixture's. The bike will now idle smooth as low as 1100, I have it set to 1400. Power is smooth up to 14k. The bike is ready to go, as soon as the...
Forum: 1986 - 2007 Ninja 250R Tech Talk May 21st, 2011, 05:47 PM
Replies: 45
Views: 5,876
Posted By Ragnar1x
I just forget to mention it, I did sync the carbs...

I just forget to mention it, I did sync the carbs prior to any of this. I will probably go back and sync again, and fine tune the idle mixture once more because I know it can be a little better than...
Forum: 1986 - 2007 Ninja 250R Tech Talk May 21st, 2011, 01:07 PM
Replies: 45
Views: 5,876
Posted By Ragnar1x
Update here. I bought a very slightly used tank...

Update here. I bought a very slightly used tank without leaks or rust. It's not here yet, but I thought I'd finish working on the bike with the leaking tank; I simply was only putting in a gallon at...
Forum: 1986 - 2007 Ninja 250R Tech Talk May 17th, 2011, 08:56 AM
Replies: 4
Views: 1,841
Posted By Ragnar1x
That is exactly what I was looking for. Thanks.

That is exactly what I was looking for. Thanks.
Forum: 1986 - 2007 Ninja 250R Tech Talk May 12th, 2011, 07:29 AM
Replies: 4
Views: 1,841
Posted By Ragnar1x
If i buy a CA tank, is it as simple as just...

If i buy a CA tank, is it as simple as just plugging up the additional emissions hose?
Forum: 1986 - 2007 Ninja 250R Tech Talk May 11th, 2011, 05:04 PM
Replies: 4
Views: 1,841
Posted By Ragnar1x
Gas Tank compatibility???

So, I'm in need of a new gas tank. I'd rather not go new OEM simply because of the price. However, I'm looking at OEM prices and they vary greatly from one year to the next. Are these tanks...
Forum: 1986 - 2007 Ninja 250R Tech Talk May 11th, 2011, 04:25 PM
Replies: 10
Views: 4,577
Posted By Ragnar1x
From Purspeeds DIY From what I recall...

From Purspeeds DIY

From what I recall 87in/lbs is exactly what the manual suggests, and is what torqued mine to.
Forum: 1986 - 2007 Ninja 250R Tech Talk May 11th, 2011, 01:39 PM
Replies: 10
Views: 4,577
Posted By Ragnar1x
You have to disconnect the cable from the little...

You have to disconnect the cable from the little arm on the clutch cover to get to one of the bolts easier. You do not have to completely unmount the cable from the cover though.

I think the...
Forum: 1986 - 2007 Ninja 250R Tech Talk May 11th, 2011, 12:56 PM
Replies: 2
Views: 1,052
Posted By Ragnar1x
You will have to drain your oil prior to changing...

You will have to drain your oil prior to changing that gasket. Might want to pick up a crush washer for the oil drain plug while your at it.
Forum: 1986 - 2007 Ninja 250R Tech Talk May 11th, 2011, 08:39 AM
Replies: 45
Views: 5,876
Posted By Ragnar1x
I found a tank off the CA model. Will it fit...

I found a tank off the CA model. Will it fit non-CA model bike? It looks like it will fit, however the part numbers are slightly different. I think the part numbers may be different simply because of...
Forum: 1986 - 2007 Ninja 250R Tech Talk May 10th, 2011, 10:07 AM
Replies: 45
Views: 5,876
Posted By Ragnar1x
The dealer just said they cannot honor the recall...

The dealer just said they cannot honor the recall because all the bolts are the same correct length. The PO must have just stuck a random bolt in there that was too long. I cant find a used tank...
Forum: 1986 - 2007 Ninja 250R Tech Talk May 9th, 2011, 01:43 PM
Replies: 45
Views: 5,876
Posted By Ragnar1x
I never put the fairing bolts back on. This must...

I never put the fairing bolts back on. This must have been a pre-existing problem. I did ride the bike prior to purchasing, it ran ok. The tank had about half a gallon in it. I was told by the...
Forum: 1986 - 2007 Ninja 250R Tech Talk May 9th, 2011, 12:43 PM
Replies: 45
Views: 5,876
Posted By Ragnar1x
I have all the valves currently in spec, on the...

I have all the valves currently in spec, on the loose side. I started to put everything back together and was going to sync the carbs, after I shimmed the needles. I go to the gas station, fill up...
Forum: 1986 - 2007 Ninja 250R Tech Talk April 29th, 2011, 11:12 AM
Replies: 45
Views: 5,876
Posted By Ragnar1x
My parts came in yesterday. I got the rocker arm...

My parts came in yesterday. I got the rocker arm and hardware installed and adjusted all the intake valves. I ran out of daylight, I plan on adjusting the exhaust this weekend and then syncing the...
Forum: 1986 - 2007 Ninja 250R Tech Talk April 22nd, 2011, 02:01 PM
Replies: 45
Views: 5,876
Posted By Ragnar1x
Thanks. By that explanation, I'll probably go a...

Thanks. By that explanation, I'll probably go a little on the loose side.
Forum: 1986 - 2007 Ninja 250R Tech Talk April 22nd, 2011, 12:55 PM
Replies: 45
Views: 5,876
Posted By Ragnar1x
I haven't checked or adjusted anything yet. I was...

I haven't checked or adjusted anything yet. I was too concerned in finding the missing rocker arm. For clarity, tight is low clearance and loose is high clearance?
Forum: 1986 - 2007 Ninja 250R Tech Talk April 22nd, 2011, 12:46 PM
Replies: 45
Views: 5,876
Posted By Ragnar1x
It was the intake valve closest to the timing...

It was the intake valve closest to the timing chain. Also, when adjusting the valves, is it best to set them to the low, mid, or high end of the specs?
Forum: 1986 - 2007 Ninja 250R Tech Talk April 22nd, 2011, 09:26 AM
Replies: 45
Views: 5,876
Posted By Ragnar1x
Good Post, thanks for the info. The valve itself...

Good Post, thanks for the info. The valve itself shouldn't be damaged, correct? There is no interference between the piston and the valve? I guess I'm asking, Should I take the valve out and...
Forum: 1986 - 2007 Ninja 250R Tech Talk April 22nd, 2011, 07:25 AM
Replies: 45
Views: 5,876
Posted By Ragnar1x
I did more searching. I found and was able to...

I did more searching. I found and was able to remove the nut, screw, and HALF of the rocker arm. It was broken in half. Thats why it fell off in the first place. They were all together and fell into...
Forum: 1986 - 2007 Ninja 250R Tech Talk April 22nd, 2011, 12:49 AM
Replies: 45
Views: 5,876
Posted By Ragnar1x
Yeah, I guess I have to assume they are still...

Yeah, I guess I have to assume they are still there. I can't imagine anybody putting it back together without them. I only spent a minute or two looking at it tonight, I'll try and get some pictures...
Forum: 1986 - 2007 Ninja 250R Tech Talk April 21st, 2011, 06:37 PM
Replies: 45
Views: 5,876
Posted By Ragnar1x
So I found these parts. ...

So I found these parts. http://www.bikebandit.com/houseofmotorcycles/2006-kawasaki-ninja-250r-ex250f6f-us/o/m9804#sch435895

I'm missing 12016, 92009 and 92015. Is there anything that holds down...
Forum: 1986 - 2007 Ninja 250R Tech Talk April 21st, 2011, 06:02 PM
Replies: 45
Views: 5,876
Posted By Ragnar1x
Missing Rocker arm and valve adjust screw/nut

So I just bought an 06 250R and it has just about 7000 miles on it. I was informed by this forum to do a valve adjustment. I just got into it today and I found the rocker arm and valve adjustment...
Forum: 1986 - 2007 Ninja 250R Tech Talk April 21st, 2011, 10:30 AM
Replies: 4
Views: 1,905
Posted By Ragnar1x
Do you know what size socket I need for it? I'll...

Do you know what size socket I need for it? I'll probably just go buy one at autozone or someplace.
Forum: 1986 - 2007 Ninja 250R Tech Talk April 20th, 2011, 05:43 PM
Replies: 4
Views: 1,905
Posted By Ragnar1x
Quick question, spark plug removal

Is the 08+ spark plug removal tool the same as the pre-gens? My 06 didn't come with a tool kit, and I can find more new gen tool kits for sale than pre gen.
Forum: 1986 - 2007 Ninja 250R Tech Talk April 19th, 2011, 11:53 AM
Replies: 15
Views: 34,827
Posted By Ragnar1x
So, I picked up the 06 250R. I was wrong about...

So, I picked up the 06 250R. I was wrong about the mileage, there are 7000 miles on it. I think I like seeing that number better than 2000. At least I know it was used, rather than just sitting in...
Showing results 1 to 25 of 28
Page 1 of 2 1 2

 
Forum Jump




Motorcycle Safety Foundation

All times are GMT -7. The time now is 12:06 PM.

Contact Us - ninjette.org - Archive - Terms of Service - Top

Website uptime monitoring Host-tracker.com
Powered by vBulletin®
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
User Alert System provided by Advanced User Tagging (Lite) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
Except where otherwise noted, all site contents are © Copyright 2022 ninjette.org, All rights reserved.