Forum: Motorcycle-related
March 18th, 2015, 06:22 AM
|
Replies: 79
Views: 8,752
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
November 8th, 2014, 12:01 PM
|
Replies: 14
Views: 1,831
Well put the carbs back on after a very indepth...
Well put the carbs back on after a very indepth cleaning with a new jet set up (40 pilot 110 main). Bike had zero issues starting up, but the minute you gave it some throttle it would die. Carbs are...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
October 27th, 2014, 08:28 AM
|
Replies: 14
Views: 1,831
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
October 27th, 2014, 08:08 AM
|
Replies: 14
Views: 1,831
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
October 27th, 2014, 05:23 AM
|
Replies: 14
Views: 1,831
So I think I am going to push forward with...
So I think I am going to push forward with adjusting the valves since the bike is about 1000 miles past the 7500 mile maintenance check. Any advice regarding the procedure? I'm am definitely...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
October 12th, 2014, 09:58 AM
|
Replies: 14
Views: 1,831
|
Forum: Motorcycle-related
October 10th, 2014, 08:45 AM
|
Replies: 159
Views: 18,743
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
October 10th, 2014, 08:43 AM
|
Replies: 14
Views: 1,831
Advice while bike is torn apart
So I just finished removing my airbox to install pod filters and do some general maintenance / cleaning. My question is this: Is there anything else I should do or mod while my bike is torn down?
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
March 1st, 2014, 05:33 PM
|
Replies: 5
Views: 1,496
Battery Replacement
As is my luck, warm weather finally rolls around and my battery has a dead cell in it. Ironically, I have had it on a battery tender for most of the winter in hopes of avoiding any battery related...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
November 20th, 2013, 01:17 PM
|
Replies: 3
Views: 681
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
November 20th, 2013, 12:42 PM
|
Replies: 3
Views: 681
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
November 20th, 2013, 12:34 PM
|
Replies: 3
Views: 681
Weak Vacuum
So a while back I had to replace my fuel petcock as it was damaged, but I am still running into the same issue; bike will only run with petcock in PRIME position. I disconnected the vacuum hose at...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
October 24th, 2013, 11:05 AM
|
Replies: 5
Views: 807
In need of assistance - fuel / oil issues
Hey guys,
I'll try and make this quick and to the point.
Background:
Fuel petcock was messed up upon purchase (used with 1000 miles).
Vacuum valve messed up and will only allow fuel flow if...
|
Forum: Motorcycle-related
September 1st, 2013, 07:21 AM
|
Replies: 15
Views: 1,743
|
Forum: Motorcycle-related
August 17th, 2013, 10:54 AM
|
Replies: 144
Views: 14,109
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
August 17th, 2013, 10:46 AM
|
Replies: 5
Views: 1,085
I've been told that a big factor is the lack of...
I've been told that a big factor is the lack of rubber damper like the stock sprocket has. That being sad, I have the JT 15t and it is much noisier than the stock one used to be. I later purchased...
|
Forum: Motorcycle-related
July 21st, 2013, 10:28 AM
|
Replies: 63
Views: 4,905
|
Forum: Cargo Space
June 12th, 2013, 08:05 PM
|
Replies: 11
Views: 5,333
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
June 7th, 2013, 07:14 PM
|
Replies: 6
Views: 1,673
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
June 7th, 2013, 07:09 AM
|
Replies: 6
Views: 1,673
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
June 5th, 2013, 05:52 PM
|
Replies: 6
Views: 1,673
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
June 5th, 2013, 05:10 PM
|
Replies: 6
Views: 1,673
Fuel Petcock Issue
While I was shimming the carbs, I noticed that the fuel petcock was set to PRIME rather than ON, and I have been ridding the bike without any apparent issues for over 1000 miles now. Upon setting it...
|
Forum: General Motorcycling Discussion
May 29th, 2013, 03:18 PM
|
Replies: 8,589
Views: 1,082,281
|
Forum: Motorcycle-related
May 14th, 2013, 06:58 AM
|
Replies: 303
Views: 36,924
|
Forum: General Motorcycling Discussion
May 9th, 2013, 10:40 AM
|
Replies: 8,589
Views: 1,082,281
|