ninjette.org

Go Back   ninjette.org > Search Forums

Showing results 1 to 25 of 1000
Search took 0.07 seconds.
Search: Posts Made By: DannoXYZ
Forum: 1986 - 2007 Ninja 250R Tech Talk Today, 09:04 PM
Replies: 136
Views: 2,712
Posted By DannoXYZ
brazing aluminium is much more difficult than...

brazing aluminium is much more difficult than steel because you have to sand both sides to bare metal to remove the oxide layer. Then temperature cannot be determined by glow of metal. Very narrow...
Forum: 2008 - 2012 Ninja 250R Tech Talk Today, 12:12 PM
Replies: 8
Views: 104
Posted By DannoXYZ
Hi Collin, welcome to Ninjette!!! :wave: ...

Hi Collin, welcome to Ninjette!!! :wave:

Here's how factory ignition switch is wired. Colours on yours may be different, but as long as connections are same, it should work fine.
...
Forum: Ninjettes At Speed Yesterday, 10:40 PM
Replies: 29
Views: 1,028
Posted By DannoXYZ
That turned out great! Aside from noise...

That turned out great! Aside from noise regulations, I really don't like loud bikes, gives me headache after day at track.

Here's where I chopped mine, just 2-3cm after seat-mounting bracket.
...
Forum: 1986 - 2007 Ninja 250R Tech Talk Yesterday, 12:04 AM
Replies: 26
Views: 347
Posted By DannoXYZ
yeah, pressure-plate is hung up on outside....

yeah, pressure-plate is hung up on outside. Shouldn't be able to spin it at all.
Forum: 1986 - 2007 Ninja 250R Tech Talk October 22nd, 2021, 09:57 AM
Replies: 26
Views: 347
Posted By DannoXYZ
Oh yeah, test your work! After taking off side...

Oh yeah, test your work! After taking off side cover, you can reach in between fingers and jiggle the plates! That's because with pressure-plate not lined up with dimples, it gets hung up on raised...
Forum: 1986 - 2007 Ninja 250R Tech Talk October 21st, 2021, 06:19 PM
Replies: 26
Views: 347
Posted By DannoXYZ
I thought you had clutch-dragging not fully...

I thought you had clutch-dragging not fully releasing problem before?
Forum: Riding Skills October 20th, 2021, 03:28 PM
Replies: 13
Views: 676
Posted By DannoXYZ
Actually, you'll want to incorporate BOTH...

Actually, you'll want to incorporate BOTH techniques into your riding as they are both valid depending upon conditions. At higher-speeds, you'll want to place body inside of bike to lean it less to...
Forum: 1986 - 2007 Ninja 250R Tech Talk October 20th, 2021, 02:42 PM
Replies: 136
Views: 2,712
Posted By DannoXYZ
oh YES! I'm starting to lose hair in my old...

oh YES! I'm starting to lose hair in my old age!!!:doh:
Forum: 2008 - 2012 Ninja 250R Tech Talk October 20th, 2021, 08:34 AM
Replies: 9
Views: 319
Posted By DannoXYZ
Lots of threads here on cleaning carbs. Do...

Lots of threads here on cleaning carbs.
Do search for "clean carbs ducatiman".

Yes to soft copper wire, no to hard wires of any kind.
Forum: 1986 - 2007 Ninja 250R Tech Talk October 20th, 2021, 08:24 AM
Replies: 136
Views: 2,712
Posted By DannoXYZ
heh, heh... always test for residual petrol...

heh, heh... always test for residual petrol vapours before welding on tank...

https://drive.google.com/uc?export=download&id=1_kLFrIpwntmxiDiaa-Th3QWfe8US-qTA

one way to fix dent is to pour 2cc...
Forum: 1986 - 2007 Ninja 250R Tech Talk October 20th, 2021, 08:16 AM
Replies: 40
Views: 623
Posted By DannoXYZ
I just worry about the short adapter section....

I just worry about the short adapter section. Wire-gauge looks little thin. Did you use W-die on crimper or just one of those squeezy crescent shapes?

Bad battery can draw down voltage due to not...
Forum: 1986 - 2007 Ninja 250R Tech Talk October 20th, 2021, 01:06 AM
Replies: 40
Views: 623
Posted By DannoXYZ
No need to connect brown wire as it's turn-ON...

No need to connect brown wire as it's turn-ON signal for factory RR. So back to basic measurements:


1. measure battery DC voltage before starting. Voltage = ??
2. measure impedance/resistance...
Forum: New Members October 20th, 2021, 12:25 AM
Replies: 4
Views: 93
Posted By DannoXYZ
Hi Bradly and welcome to Ninjette! :wave: ...

Hi Bradly and welcome to Ninjette! :wave:

Here's minimal diagram for kart using 88-07 Ninja 250 engine. Compare to wiring diagram of ZX9R and it should be similar. Note the 100-ohm resistor...
Forum: 1986 - 2007 Ninja 250R Tech Talk October 19th, 2021, 08:09 PM
Replies: 136
Views: 2,712
Posted By DannoXYZ
skip epoxy, not gonna work. Force required is way...

skip epoxy, not gonna work. Force required is way beyond its strength.

Try brazing some bolts on head-first and using slide hammer. Removing bolt is easy afterwards, just heat up brass until it's...
Forum: 2008 - 2012 Ninja 250R Tech Talk October 19th, 2021, 06:06 PM
Replies: 9
Views: 140
Posted By DannoXYZ
Unless dealer has old guy hidden in back who've...

Unless dealer has old guy hidden in back who've been around since Civil War having worked on carbs for at least 50-yrs, not likely they'll be able to help you. I sent my 2009 to local dealer to get...
Forum: 2008 - 2012 Ninja 250R Tech Talk October 19th, 2021, 05:39 PM
Replies: 9
Views: 140
Posted By DannoXYZ
Hi Noah, welcome to Ninjette!!! :wave: I had...

Hi Noah, welcome to Ninjette!!! :wave:

I had exact same problem with my 2008 track-bike and 2009 street-bike. Same symptoms, starts up and runs for little bit, then died forever. Turns out...
Forum: 1986 - 2007 Ninja 250R Tech Talk October 19th, 2021, 05:14 PM
Replies: 40
Views: 623
Posted By DannoXYZ
Here's an idea, mounting it in stock location,...

Here's an idea, mounting it in stock location, but slid back about 4cm to allow cable connectors to fit. You can make mounting plate that bolts to factory location, then provides 2nd set of studs...
Forum: 1986 - 2007 Ninja 250R Tech Talk October 19th, 2021, 01:34 PM
Replies: 136
Views: 2,712
Posted By DannoXYZ
Good job on caliper-rebuild! Better now than in...

Good job on caliper-rebuild! Better now than in year when brakes lock-up on you! Yeah, silicone-lube for seals. Don't use petroleum grease because it'll degrade your seals! Might even be why yours...
Forum: General Motorcycling Discussion October 19th, 2021, 01:18 PM
Replies: 22
Views: 312
Posted By DannoXYZ
This is awesome idea! Easier to press on rim so...

This is awesome idea! Easier to press on rim so 2nd bead is seated and sealed evenly! No need for 3-hands trying to lift tyre. I'm gonna try this next time! Thanks for tip!!! :) :clapping:
Forum: General Motorcycling Discussion October 19th, 2021, 01:09 PM
Replies: 15
Views: 244
Posted By DannoXYZ
Perhaps change pricing model of electric cars....

Perhaps change pricing model of electric cars. Leave out the battery and let end-user pick battery of their choice. They can buy one new or used, or rent one. Rich folks can splurge for super...
Forum: General Motorcycling Discussion October 19th, 2021, 11:34 AM
Replies: 15
Views: 244
Posted By DannoXYZ
I think big breakthrough will be interchangeable...

I think big breakthrough will be interchangeable battery-packs for instant refills at service-stations. The Japanese bike manufacturers are collaborating their designs around that. Hopefully...
Forum: 2013 - 2017 Ninja 300 Tech Talk October 19th, 2021, 11:12 AM
Replies: 7
Views: 164
Posted By DannoXYZ
By "end of the lever", do you mean...

By "end of the lever", do you mean engagement/disengagement point is close to end when you release lever? Or when you start to release lever? Try to adjust so engagement is closer to middle:

end...
Forum: 1986 - 2007 Ninja 250R Tech Talk October 19th, 2021, 09:09 AM
Replies: 26
Views: 347
Posted By DannoXYZ
Yup, even though there's 4 spring posts and 4...

Yup, even though there's 4 spring posts and 4 possible ways to install spring/pressure plate, only TWO of orientations will work. Look carefully and you'll see that teeth next to some posts are...
Forum: 1986 - 2007 Ninja 250R Tech Talk October 18th, 2021, 10:36 PM
Replies: 26
Views: 347
Posted By DannoXYZ
ah, this sounds like spring/pressure-plate isn't...

ah, this sounds like spring/pressure-plate isn't moving inwards and squeezing stack together.

1. did you put 2x clutch plates with wider blocks as 1st and last plates installed?

2. did you line...
Forum: 2013 - 2017 Ninja 300 Tech Talk October 18th, 2021, 03:04 PM
Replies: 7
Views: 164
Posted By DannoXYZ
Could be slipper-clutch, although its action...

Could be slipper-clutch, although its action doesn't come into play until you're engine-braking.

Do you have cable well-lubed? With both ends disconnected, drip oil into upper end while you floss...
Showing results 1 to 25 of 1000

 
Forum Jump




Motorcycle Safety Foundation

All times are GMT -7. The time now is 09:07 PM.


remote server monitor
Powered by vBulletin®
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.
User Alert System provided by Advanced User Tagging (Lite) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.
Except where otherwise noted, all site contents are © Copyright 2021 ninjette.org, All rights reserved.