Forum: 1986 - 2007 Ninja 250R Farkles
October 28th, 2014, 06:10 PM
|
Replies: 17
Views: 6,777
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
September 11th, 2013, 04:27 PM
|
Replies: 16
Views: 2,028
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
September 11th, 2013, 04:25 PM
|
Replies: 16
Views: 2,028
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
September 11th, 2013, 09:21 AM
|
Replies: 16
Views: 2,028
Well there doesn't seem to be any air in the...
Well there doesn't seem to be any air in the cooling system as the coolant level has not changed. Not sure if it is the idle problems causing the high temps, or what. Just getting her on the road...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
September 11th, 2013, 08:17 AM
|
Replies: 16
Views: 2,028
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
September 11th, 2013, 07:42 AM
|
Replies: 16
Views: 2,028
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
September 11th, 2013, 06:41 AM
|
Replies: 16
Views: 2,028
carb problems with video
The first & second video is of the bike before the carb rebuild. I only replaced the float needles because of the fuel bowl overflow, and sprayed the jets with some carb cleaner.
The third video...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
September 11th, 2013, 12:59 AM
|
Replies: 10
Views: 2,033
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
September 9th, 2013, 09:09 PM
|
Replies: 10
Views: 2,033
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
September 9th, 2013, 08:28 PM
|
Replies: 10
Views: 2,033
Normal operating temp
I know the ninjette's are famous for being cold blooded, but I'm new to them and was wondering what the normal operating temp is? Also, what temp is considered overheating on these bikes?
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
August 10th, 2013, 08:07 AM
|
Replies: 3
Views: 767
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
August 10th, 2013, 05:57 AM
|
Replies: 3
Views: 767
Oil level question
I changed the oil and filter. I made sure there was an appropriate amount of oil. I started the bike to check the idle, everything was fine. Now after not starting the bike for 2 months the oil level...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
June 20th, 2013, 06:28 PM
|
Replies: 47
Views: 5,191
disconnect battery. unbolt the starter wire....
disconnect battery. unbolt the starter wire. Helpful to remove the airbox for more room. drain oil. drain coolant. remove coolant tube. remove the gear lever. pull the left side cover. unbolt the...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
June 20th, 2013, 06:22 PM
|
Replies: 4
Views: 1,108
not at all. really straight forward, but i did...
not at all. really straight forward, but i did have most of the bike apart already to try to run through it fully. I bought it from an impound yard and it wasn't running due to a trashed carb, and...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
May 14th, 2013, 11:23 AM
|
Replies: 4
Views: 1,108
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
May 13th, 2013, 10:04 PM
|
Replies: 4
Views: 1,108
replacing starter motor
I have just completed replacing the starter motor, ran into one problem, and this may not even be a problem. While reinstalling the small gear that the starter motor turns, the larger gear (behind...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
November 20th, 2012, 07:00 PM
|
Replies: 40
Views: 6,794
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
November 18th, 2012, 08:12 PM
|
Replies: 40
Views: 6,794
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
November 18th, 2012, 07:29 PM
|
Replies: 12
Views: 2,100
Thanks a bunch for the reply! I have rebuilt...
Thanks a bunch for the reply! I have rebuilt carbs in the past and the internals looked good, all of the necessary vacuum lines and fuel passages are clear. Both diaphragms are in good shape. I'd...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
November 18th, 2012, 07:15 PM
|
Replies: 12
Views: 2,100
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
November 18th, 2012, 04:09 PM
|
Replies: 12
Views: 2,100
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
November 18th, 2012, 09:22 AM
|
Replies: 12
Views: 2,100
Okay, so I've done a good bit of research. It...
Okay, so I've done a good bit of research. It looks like the carb is missing the plunger,starter (#16016)
http://www.kawasakipartshouse.com/oemparts/a/kaw/500b267ff8700223e4790681/carburetor-parts...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
November 17th, 2012, 08:22 PM
|
Replies: 12
Views: 2,100
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
November 17th, 2012, 06:10 PM
|
Replies: 12
Views: 2,100
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
November 17th, 2012, 12:45 PM
|
Replies: 12
Views: 2,100
carb rebuild help
What the heck are the two holes that go into the carb body? Don't remember removing anything from either of them, but only the top one looks like there should be something going to it!...
|