Forum: 2008 - 2012 Ninja 250R Farkles
June 6th, 2017, 01:42 PM
|
|
Replies: 54
Views: 12,781
|
|
Forum: 2008 - 2012 Ninja 250R Farkles
June 6th, 2017, 01:38 PM
|
|
Replies: 54
Views: 12,781
|
|
Forum: 2008 - 2012 Ninja 250R Farkles
June 1st, 2017, 07:29 AM
|
|
Replies: 54
Views: 12,781
|
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
May 14th, 2017, 05:09 PM
|
|
Replies: 7
Views: 2,585
|
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
May 14th, 2017, 02:01 PM
|
|
Replies: 7
Views: 2,585
|
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
May 13th, 2017, 07:07 PM
|
|
Replies: 7
Views: 2,585
To anyone who might have helped me out here....
To anyone who might have helped me out here. Thanks anyway. (NO sarcasm intended)
I did find the info I was looking for and the swap is done. The best write up of the basics required was here:...
|
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
May 13th, 2017, 05:12 PM
|
|
Replies: 2
Views: 874
I have been here. While it is a different...
I have been here. While it is a different application, I have put a Yamaha Banshee motor in my Ninja and needed to figure out the wiring. I would recommend that you get a good copy of the factory...
|
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
May 13th, 2017, 05:03 PM
|
|
Replies: 7
Views: 2,585
How to on GSXR shock conversion?
I searched for at least 40 minutes, but came up empty.
OK...I have the shock and I am looking to do the swap. I am a mechanic and I have a machine shop so it should be a simple swap. I just want to...
|
|
Forum: 1986 - 2007 Ninja 250R Farkles
October 14th, 2014, 06:57 AM
|
|
Replies: 17
Views: 6,794
|
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
July 18th, 2014, 07:12 PM
|
|
Replies: 9
Views: 2,031
|
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
July 15th, 2014, 09:32 AM
|
|
Replies: 9
Views: 2,031
Even easier....
I have done a bunch of these and you do not need to make a puller. You simply need to break off any remaining plastic, grab the brass that's left with a vice grip, and while rotating it back and...
|
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
May 29th, 2014, 09:49 AM
|
|
Replies: 32
Views: 3,970
The VM is a series of carb made by Mikuni since...
The VM is a series of carb made by Mikuni since the 70's. It is probably the most mass produced carb in history used on everything from dirtbikes to street bikes to snomobiles. Available in both 4...
|
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
May 15th, 2014, 10:45 AM
|
|
Replies: 140
Views: 21,663
Skip the powder coating as it will be a "built...
Skip the powder coating as it will be a "built up" finish. You would have to mask off any bolt holes and especially any mating surfaces as any powder coating between mounting surfaces will eventually...
|
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
May 8th, 2014, 11:12 PM
|
|
Replies: 1,204
Views: 108,248
Leaking gas
Don't sweat the carb over filling and leaking gas. That is actually common for any carb that sits empty for any length of time. When the float sits all the way down (empty carb) sometimes it just...
|
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
November 12th, 2013, 01:21 PM
|
|
Replies: 1,204
Views: 108,248
|
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
October 28th, 2013, 10:21 AM
|
|
Replies: 17
Views: 3,001
|
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
September 10th, 2013, 05:56 PM
|
|
Replies: 8
Views: 3,026
|
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
September 7th, 2013, 12:12 PM
|
|
Replies: 13
Views: 1,525
So you dinged the guys feedback BEFORE you...
So you dinged the guys feedback BEFORE you contacted him or gave him a chance to provide any customer service? That's pretty rough.
What you describe is exactly what is wrong with the "got it...
|
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
September 7th, 2013, 11:49 AM
|
|
Replies: 8
Views: 1,445
|
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
July 14th, 2013, 11:51 PM
|
|
Replies: 17
Views: 8,898
|
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
July 14th, 2013, 11:03 PM
|
|
Replies: 17
Views: 8,898
My .02 on torque wrenches.
Unless you have the $$ to buy very high quality, and commit to having it calibrated regularly, stay away from "clicker" wrenches. They are complex tools that have multiple moving parts. The ONLY way...
|
|
Forum: 2008 - 2012 Ninja 250R Farkles
July 13th, 2013, 06:21 PM
|
|
Replies: 208
Views: 38,687
|
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
July 10th, 2013, 11:00 AM
|
|
Replies: 1,204
Views: 108,248
|
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
July 10th, 2013, 08:40 AM
|
|
Replies: 1,204
Views: 108,248
|
|
Forum: Items Wanted
July 9th, 2013, 06:34 PM
|
|
Replies: 2
Views: 836
I have one.
It's even from a 2010 and has about 6K miles on it. I took it out to swap a 2 stroke motor in my bike. I took a video of it running before I removed it where you can clearly see the engine numbers...
|
