ninjette.org

Go Back   ninjette.org > Search Forums

Notices

Showing results 1 to 25 of 386
Search took 0.01 seconds.
Search: Posts Made By: daverdfw
Forum: 2013 - 2017 Ninja 300 Tech Talk March 17th, 2020, 03:03 PM
Replies: 40
Views: 10,411
Posted By daverdfw
I think I am going to just get it back together...

I think I am going to just get it back together and ride it and go from there. If I decide to keep it and replace my other track bike I can always do rings later if I feel its down on power.
Forum: 2013 - 2017 Ninja 300 Tech Talk March 16th, 2020, 09:12 PM
Replies: 40
Views: 10,411
Posted By daverdfw
interesting, I wonder why the service manual...

interesting, I wonder why the service manual states such a higher value? 162 ∼ 246 psi

also did a wet test and got 175
Forum: 2013 - 2017 Ninja 300 Tech Talk March 15th, 2020, 03:40 PM
Replies: 40
Views: 10,411
Posted By daverdfw
due to the fact this is a track only bike and...

due to the fact this is a track only bike and would spend most of its live above 10K RPM anyway, and since I have the bike fully stripped, I might just drop the motor and do rings to be safe. Its...
Forum: 2013 - 2017 Ninja 300 Tech Talk March 15th, 2020, 01:57 PM
Replies: 40
Views: 10,411
Posted By daverdfw
this is the tool I used ...

this is the tool I used

https://www.amazon.com/gp/product/B07WZF4LQF/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1
Forum: 2013 - 2017 Ninja 300 Tech Talk March 15th, 2020, 01:21 PM
Replies: 40
Views: 10,411
Posted By daverdfw
eh not quite, after running it to get it warm,...

eh not quite, after running it to get it warm, still 145 each side :(
Forum: 2013 - 2017 Ninja 300 Tech Talk March 15th, 2020, 09:39 AM
Replies: 40
Views: 10,411
Posted By daverdfw
just as an update, did the valve job, cold/dry...

just as an update, did the valve job, cold/dry compression is 150psi on each cylinder.
Forum: 2013 - 2017 Ninja 300 Tech Talk March 14th, 2020, 12:36 PM
Replies: 40
Views: 10,411
Posted By daverdfw
the PAIR valve is gone, so I ordered a block off...

the PAIR valve is gone, so I ordered a block off plate and a plug to get rid of the CEL from the sensor. I will put a K&N filter on it and run without the airbox.
Forum: 2013 - 2017 Ninja 300 Tech Talk March 13th, 2020, 09:24 PM
Replies: 40
Views: 10,411
Posted By daverdfw
hooked up new throttle bodies, problem solved....

hooked up new throttle bodies, problem solved. Now to finish the valve job
Forum: 2013 - 2017 Ninja 300 Tech Talk March 7th, 2020, 07:37 PM
Replies: 40
Views: 10,411
Posted By daverdfw
here are the results of the valve clearance ...

here are the results of the valve clearance

looks like I will be replacing the intake shims, should improve compression as well I would assume
...
Forum: 2013 - 2017 Ninja 300 Tech Talk March 7th, 2020, 11:09 AM
Replies: 40
Views: 10,411
Posted By daverdfw
OK I will take a look at that, also since...

OK I will take a look at that,

also since compression was "ok" going to take a look at the valve clearances as well.
Forum: 2013 - 2017 Ninja 300 Tech Talk March 7th, 2020, 10:42 AM
Replies: 40
Views: 10,411
Posted By daverdfw
got a new dash in, was able to find the codes,...

got a new dash in, was able to find the codes, there are 2

64 Air switching valve malfunction, wiring open or short

32 Subthrottle sensor malfunction, wiring open or short

so the subthorrle...
Forum: 2013 - 2017 Ninja 300 Tech Talk March 6th, 2020, 10:47 AM
Replies: 40
Views: 10,411
Posted By daverdfw
UPDATE ran the engine in the garage for...

UPDATE


ran the engine in the garage for about 5 min, so not sure if thats warm enough etc. The smoke that PO said was present disappeared after a few mine. did a warm compression check and my...
Forum: 2013 - 2017 Ninja 300 Tech Talk March 5th, 2020, 07:12 PM
Replies: 7
Views: 3,950
Posted By daverdfw
makes sense, but I thought there is a...

makes sense, but I thought there is a Sub-throttle sensor? there is a TPS sensor which is grey, and then the servor motor has a connector and then on top of the server motor is another sensor with a...
Forum: 2013 - 2017 Ninja 300 Tech Talk March 4th, 2020, 08:51 AM
Replies: 7
Views: 3,950
Posted By daverdfw
What are my throttle bodies sub-throttle doing here?

Have another thread about a race bike I bough that I am trying to fix, as soon as I turn the power on I heard clicking.

I pull the airbox and see this
...
Forum: 2013 - 2017 Ninja 300 Tech Talk March 2nd, 2020, 06:57 PM
Replies: 40
Views: 10,411
Posted By daverdfw
ok check this out, this is the secondary...

ok check this out, this is the secondary sub-throttle. if I open the butterfly they will close when turn the key on, if they are already closed they make the noise like they cant figure out if they...
Forum: 2013 - 2017 Ninja 300 Tech Talk March 2nd, 2020, 05:24 PM
Replies: 40
Views: 10,411
Posted By daverdfw
ok, maybe ill take it off and make sure its...

ok, maybe ill take it off and make sure its installed correctly,

ok, I ordered a new radiator so I will try getting it running then and will go from there with a warm compression test.

Kinda...
Forum: 2013 - 2017 Ninja 300 Tech Talk March 2nd, 2020, 05:12 PM
Replies: 40
Views: 10,411
Posted By daverdfw
it was more than a little LOL, but i can see the...

it was more than a little LOL, but i can see the top of the piston so I am sure its fine.

With those compression numbers, should I just put it back together and run it and do a warm compression...
Forum: 2013 - 2017 Ninja 300 Tech Talk March 2nd, 2020, 02:59 PM
Replies: 40
Views: 10,411
Posted By daverdfw
hypothetical question, what if someone ( an...

hypothetical question, what if someone ( an idiot) was trying to put oil in the cylinder to do a wet test, and a little bit too much oil in? would it just burn off once the engine was started?
Forum: 2013 - 2017 Ninja 300 Tech Talk March 2nd, 2020, 02:20 PM
Replies: 40
Views: 10,411
Posted By daverdfw
so I put the emissions hose back on the airbox,...

so I put the emissions hose back on the airbox, and left the other one open because I don't have a tiny filter.

Compression check on both cylinders cold and dry , is 125 after the needle stopped...
Forum: 2013 - 2017 Ninja 300 Tech Talk March 2nd, 2020, 12:54 PM
Replies: 40
Views: 10,411
Posted By daverdfw
to me it seems instead of using the emissions...

to me it seems instead of using the emissions block off plate, they routed that hose to the crankcase breather that use to go to the airbox, why not just block the plate off and then install a tiny...
Forum: 2013 - 2017 Ninja 300 Tech Talk March 1st, 2020, 10:13 PM
Replies: 40
Views: 10,411
Posted By daverdfw
here is the routing of the breather hose from the...

here is the routing of the breather hose from the top of the motor.

https://www.dropbox.com/s/qwrw22ozfn3yk1i/IMG_3277.jpg?dl=0
Forum: 2013 - 2017 Ninja 300 Tech Talk March 1st, 2020, 09:24 PM
Replies: 40
Views: 10,411
Posted By daverdfw
previous owner said he had valves checked last...

previous owner said he had valves checked last year, he had put a thinner head gasket on. He said it was smoking and was told it was probably rings.

My gauge has the Schrader valve near the gauge.
Forum: 2013 - 2017 Ninja 300 Tech Talk March 1st, 2020, 09:15 PM
Replies: 40
Views: 10,411
Posted By daverdfw
got the bike today, it needs a bit more work,...

got the bike today, it needs a bit more work, battery is dead. radiator has a leak

Looks like I will have to do a cold compression test, what numbers would be normal for a cold test? hoping to do...
Forum: 2013 - 2017 Ninja 300 Tech Talk February 21st, 2020, 02:04 PM
Replies: 40
Views: 10,411
Posted By daverdfw
Thats what I assume they did, thats what my 250...

Thats what I assume they did, thats what my 250 was. I will know when I see it. I will get it next friday.
Forum: 2013 - 2017 Ninja 300 Tech Talk February 21st, 2020, 12:22 PM
Replies: 40
Views: 10,411
Posted By daverdfw
thanks everyone for the input, I have a...

thanks everyone for the input, I have a compression tester on the way. I will report back what the values are after I get my hands on the bike next Friday.
Showing results 1 to 25 of 386

 
Forum Jump




Motorcycle Safety Foundation

All times are GMT -7. The time now is 06:50 AM.


Website uptime monitoring Host-tracker.com
Powered by vBulletin®
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
User Alert System provided by Advanced User Tagging (Lite) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
Except where otherwise noted, all site contents are © Copyright 2022 ninjette.org, All rights reserved.