ninjette.org - Search Results

		ninjette.org > Search Forums
Search Results

Showing results 1 to 14 of 14
Search took 0.00 seconds. Search: Posts Made By: Kevin H

Forum: 1986 - 2007 Ninja 250R Tech Talk

July 5th, 2013, 02:34 PM

Replies: 3

Big Bore Kit

Views: 2,141

Posted By Kevin H

Yeah, I saw that too. A lot of what they say...

Yeah, I saw that too. A lot of what they say doesn't make sense. Maybe something is being lost in translation here. I was hoping that someone on the forum with knowledge of both pre-gen and...

Forum: 1986 - 2007 Ninja 250R Tech Talk

July 3rd, 2013, 01:49 PM

Replies: 3

Big Bore Kit

Views: 2,141

Posted By Kevin H

Big Bore Kit

Will this kit fit the First Gen bikes? It states that it will fit 2005-2012 models.
...

Forum: 1986 - 2007 Ninja 250R Tech Talk

April 15th, 2013, 04:54 PM

Replies: 76

DIY: Replacing the Clutch Plates

Views: 38,940

Posted By Kevin H

What you need is a new set of springs. You can...

What you need is a new set of springs. You can check the condition of the plates and discs while your'e in there, but its a safe bet that they are fine if you havent been slipping it for too long.

Forum: 1986 - 2007 Ninja 250R Tech Talk

March 15th, 2013, 08:01 PM

Replies: 129

'08+ parts that fit Pre-Gen

Views: 42,092

Posted By Kevin H

They wont work, the plug leads are different. I'm...

They wont work, the plug leads are different. I'm not sure about the coils themselves though.

Forum: 1986 - 2007 Ninja 250R Tech Talk

March 9th, 2013, 12:53 PM

Replies: 129

'08+ parts that fit Pre-Gen

Views: 42,092

Posted By Kevin H

Use the spring rate calculator here to calculate...

Use the spring rate calculator here to calculate your ideal spring rate:http://racetech.com/ProductSearch/2/Kawasaki/EX250%20Ninja%20250R/1986-2007

If you're not a featherweight like me :o, your...

Forum: 1986 - 2007 Ninja 250R Tech Talk

February 23rd, 2013, 02:12 PM

Replies: 5

'07 250 running one cylinder

Views: 2,100

Posted By Kevin H

I had the same problem,it was a bad coil. You...

I had the same problem,it was a bad coil. You could test yours by swapping coils from one cylinder to the other. I picked up a set on ebay.

Forum: 1986 - 2007 Ninja 250R Tech Talk

November 21st, 2012, 07:53 PM

Replies: 25

Can't start - stuck in gear

Views: 2,925

Posted By Kevin H

Good, I'm interested to hear what you find. With...

Good, I'm interested to hear what you find. With an issue like this you need to eliminate each possible problem methodically, and not start jumping around and tearing it apart and possibly causing...

Forum: 1986 - 2007 Ninja 250R Tech Talk

November 17th, 2012, 06:32 PM

Replies: 28

Seized engine

Views: 4,887

Posted By Kevin H

The oil may have seeped past the rings during...

The oil may have seeped past the rings during shipping if the engine was turned upside down. Leave the plugs out, remove the flywheel bolt hole cover and try and turn the engine with a socket wrench.

Forum: 1986 - 2007 Ninja 250R Tech Talk

November 17th, 2012, 03:21 PM

Replies: 336

Bike not wanting to rev past ~5k while driving

Views: 46,210

Posted By Kevin H

Blue smoke from the pipes indicates oil, white...

Blue smoke from the pipes indicates oil, white smoke indicates coolant. The way to properly check for a coolant leak into one of the cylinders would be to pressure test the cooling system. You...

Forum: 1986 - 2007 Ninja 250R Tech Talk

November 14th, 2012, 06:58 PM

Replies: 25

Can't start - stuck in gear

Views: 2,925

Posted By Kevin H

My next move would be to pull the flywheel cover....

My next move would be to pull the flywheel cover. Then check the starter gear and starter reduction gear.

Forum: 1986 - 2007 Ninja 250R Tech Talk

November 14th, 2012, 06:26 PM

Replies: 25

Can't start - stuck in gear

Views: 2,925

Posted By Kevin H

Are you sure the battery is in good condition?

Are you sure the battery is in good condition?

Forum: 1986 - 2007 Ninja 250R Tech Talk

November 14th, 2012, 05:32 PM

Replies: 25

Can't start - stuck in gear

Views: 2,925

Posted By Kevin H

Before you start taking it apart just try and...

Before you start taking it apart just try and rotate the engine manually by removing the flywheel bolt cover and putting a socket and ratchet on it. If something is jamming the engine from turning it...

Forum: 1986 - 2007 Ninja 250R Tech Talk

October 26th, 2012, 04:21 PM

Replies: 35

Newgen rear shock in Pregen.

Views: 4,991

Posted By Kevin H

Thats surprising, that's not the case with mine....

Thats surprising, that's not the case with mine. Centerstand works fine.

Forum: 1986 - 2007 Ninja 250R Tech Talk

October 26th, 2012, 05:46 AM

Replies: 35

Newgen rear shock in Pregen.

Views: 4,991

Posted By Kevin H

I put one on mine about 500 miles ago. It made a...

I put one on mine about 500 miles ago. It made a very noticeable difference, it was the best $31.00 I've spent on this bike so far. I weigh 170 and have it set on the softest setting. But as someone...

Showing results 1 to 14 of 14

Forum Jump

All times are GMT -7. The time now is 04:04 AM.