Forum: 1986 - 2007 Ninja 250R Tech Talk
March 13th, 2017, 02:58 PM
|
Replies: 3
Views: 992
Yep -- I'm talking about the threaded ones. So...
Yep -- I'm talking about the threaded ones. So you just essentially hammered them into the tank and then skim coated with filler? Did I understand that correctly? Also great looking bike--is that...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
March 13th, 2017, 02:29 PM
|
Replies: 3
Views: 992
Gas tank mounting tabs
Anybody have a good method for removing the fairing mounting tabs from the gas tank? I've seen some fill with bondo, but wondering if there's a good way to remove without puncturing the tank...looks...
|
Forum: Buyer/Seller Feedback: Good
September 4th, 2015, 05:03 PM
|
Replies: 36
Views: 37,237
06 ninja 250 carbs
Sent my carbs in to Gordon and when I pm'd him to see if he got them...he told me he almost had them done! Got them back put them on...started right up! Great service, high quality work, and quick...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
August 23rd, 2015, 02:58 PM
|
Replies: 27
Views: 2,583
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
August 22nd, 2015, 12:56 PM
|
Replies: 27
Views: 2,583
Anybody need parts? I seriously can't get...
Anybody need parts? I seriously can't get anything even remotely resembling sustained combustion. It has now had 2 separate sets of Pistons, 3 sets of rings if you count the ones originally in it,...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
August 7th, 2015, 07:39 PM
|
Replies: 27
Views: 2,583
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
August 7th, 2015, 04:07 PM
|
Replies: 27
Views: 2,583
Ok guys... Perhaps I am just doing something...
Ok guys... Perhaps I am just doing something completely wrong. Perhaps my leak down gauge is junk...
I cleaned all the valves and lapped them. They now seal and I've validated
By seeing if they...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
August 2nd, 2015, 03:35 PM
|
Replies: 27
Views: 2,583
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
August 2nd, 2015, 03:35 PM
|
Replies: 27
Views: 2,583
While cleaning the and lapping the valves, I...
While cleaning the and lapping the valves, I decided to soak and clean the Pistons as well and clean the ring grooves. When I pulled the Pistons from the berrymans, I noticed the damage on the skirt...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
July 31st, 2015, 06:12 PM
|
Replies: 27
Views: 2,583
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
July 31st, 2015, 01:17 PM
|
Replies: 27
Views: 2,583
So I did clean the head and valves. I did not...
So I did clean the head and valves. I did not disassemble the heads from the valves and lap them though.
To answer an earlier question, I'm not running a standard compression gauge in the engine...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
July 30th, 2015, 08:44 AM
|
Replies: 27
Views: 2,583
The ring end gap for the top ring was .279 to...
The ring end gap for the top ring was .279 to .305 which is still in spec according to the manual. I replaced the rings because when I did the original leak down test, it was pretty clear the air...
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
July 29th, 2015, 09:11 PM
|
Replies: 27
Views: 2,583
|
Forum: 1986 - 2007 Ninja 250R Tech Talk
July 29th, 2015, 08:34 PM
|
Replies: 27
Views: 2,583
Help me not concede defeat...please!
First time poster, but I have used a lot of resources on this site with my recently acquired 2006 250. The tech articles discussions have been great, so thanks to all for that!
Here is my issue...
|