October 7th, 2021, 01:20 AM
|
#82
|
ninjette.org member
Name: Cashby
Location: Maine
Join Date: Sep 2021
Motorcycle(s): EX250-F x 3, TW200, NPS50
Posts: 98
|
Moving purchase list/to-do list here.
Purchased list: - (in) side covers ($35 left, $24 right)
- (in) fairing hardware ($22)
- (in) front tire (shinko 740) ($60, doesn't include mounting)
- (in) airbox assembly ($53)
- (ON)(in) air filter (airbox came with one, wasn't aware) ($12)
- (ON)(in) fuel tank dampers (2) (bought the wrong ones... 92075-1690 instead of 92075-1115) ($18) + ($21)
- (ON)(in) battery tender ($26) and extension cord ($5)
- (ON)(in) J-B weld (steelstik) for carb and clutch lever housing ($8)
- (in) The Works toilet bowl cleaner for tank ($3)
- (in) fairing bushings ($7) (probably need more)
- (ON)(in) clutch locknut and adjuster ($7)
- (ON)(in) oil (t6 15w40 1gal) ($22) and filter (wix 24941) ($8)
- (in) PVC ABS cement ($8) (fairing tab)
- (ON)(in)carb gaskets (gordon) ($50)
- (ON)(in) Blackstone ($30)
- (ON)(in) Horn (free)
- (in) DOT 4 (free)
- (ON)(in) carb spring clamps (hose clamps) ($8)
- (ON)(in) ultrasonic cleaner ($95)
- (ON)(in) 2.95x2.44x1.37 rubber stopper for gas tank ($8)
- (ON)(in) pine-sol for carb ($11)
- (ON)(in) new float ($14) (gordon)
- (in) acetone (plastic repair) ($12)
- (in) Rage Gold ($73)
- (ON)(in) Spot weld cutter ($5)
- (ON)(in) sprocket cover bolts ($13)
- (ON)(in) petcock gaskets ($23)
- (in) fuel filter ($9) (5 of them)
- (ON)(in) solenoid mount ($8) (came with a solenoid)
- (in) brazing kit ($74)
- (ON)(in) shade 5 ($8)
- (in) spot weld cutter #2 ($5)
- bar, intake, coolant, peg ($19)
- (ON)(in) petcock bolts (M3x0.5x5) and nylon washer ($3)
- (in) caliper seals ($43)
- (in) tire lube ($18)
- (in) ABS ($12)
- (in) 3 tire levers (free)
- (in) Al3 rods ($9)
- (in) powder flux ($11)
- (in) acetone 2 ($3)
Total running cost:
$1070
Still need to buy (~$100): - M8x1.25 tap ($10)
- Maybe extra tire valve stems 11.3mm ($8/pair)
- fork dust caps ($10)
- shorty levers (don't like the stock ones and clutch lever needs spacers) ($30-60)
- front tire mount ($50) (going to try to do it myself)
- (thinking about going white, green, or yellow. I went through a very long thread here with colour templates and liked a couple) (leaning towards white body with green/yellow decals/frame) paint and decal ($50)
maybe something like this, needs more 90s vibe though.
Still need to do: - front foot peg brazed, threaded, bolted
- airbox cap gasket (maybe)
- airbox in (bracket first)
- handlebars drilled, tapped, weighted, back on
- battery situation (finish bracket, see about tie downs)
- sync carb (ghostt, feeler gauge)
- inline fuel filter cut
- braze tank tab
- gas tank rust (The Works, it works)
- gas tank dent (body filler, braze)
- Install carb
- cables back on
- Mount tire
- coolant tank installed
- New coolant
- check thermostat operation
- try to start bike
- plastic weld (danno post, time consuming)
- front tire mounted (self probably, $50 local)
- brake seals/rebuild
- brake bleed (after tire)
- wrap harness
- clean and oil chain
- spark plug cover? (nah?)
- mount plastics (hardware has been cut)
- Paint plastics
- Braided lines
Last futzed with by BonelessSugar; November 7th, 2021 at 02:30 PM.
|
|
|