June 11th, 2018, 09:25 PM | #1 |
ninjette.org member
Name: David
Location: Mexico
Join Date: Sep 2017 Motorcycle(s): 2010 Kawasaki Ninja 250R, 99' Suzuki Katana 600 (RIP) Posts: 95
|
Size of handlebar end side mirrors
Hi guys, i have some questions, what are the size of the stock handlebar from a 2010 ninja 250, because i want to put some handlebar mirrors, and in some webpages (Aliexpress) they sold for "sizes", somebody know what is the size of the handlebar? I want some mirrors like this
Also i was looking and they sell some "Mirror Block off plates" to put where the normal mirrors put on the bike, someone know if i need to buy that mirror block plates, to make the bike look good without the normal mirrors, or someone know some tip to make the bike look good without that mirror block plates, because the mirrors block plates are cheap, but the expensive is the shipping I want to make the bike look like like this but with the handlebar mirrors ps: sorry for my bad english |
|
June 11th, 2018, 09:30 PM | #2 |
ninjette.org certified postwhore
Name: AKA JacRyann
Location: Mesa, AZ
Join Date: Dec 2011 Motorcycle(s): CB125T CBR250R-MC19 CBR250RR-MC22 NSR350R-MC21 VF500F CBR600RR SFV650 VFR750F R1M ST1300PA Valkyrie-F6C Posts: A lot.
MOTY - 2018, MOTM - Nov '17
|
22.2mm OD
15.9mm ID Try these mirror plates. They say free shipping https://www.ebay.com/i/252051760450 |
|
June 11th, 2018, 09:34 PM | #3 |
Guy Who Enjoys Riding
Name: Jim
Location: North Carolina
Join Date: Jul 2016 Motorcycle(s): Ninja 250 Posts: A lot.
MOTM - Oct '18, Aug '17, Aug '16
|
My pregen has standard 7/8" OD bars. Mirrors like that usually will clamp to the OD. The supplied adapter will go in the bar and provide a 7/8" OD surface for the clamp to go on if you can't put it directly on the bar OD. I always clamp them right to the bars without adapters, but I had to move the throttle in about 1/2 an inch, drilling a new locating hole for it in the bar. The clutch side was probably similar, but it's been a while.
Newgens may be the same. (?) |
|
June 12th, 2018, 12:01 PM | #4 | |
ninjette.org member
Name: David
Location: Mexico
Join Date: Sep 2017 Motorcycle(s): 2010 Kawasaki Ninja 250R, 99' Suzuki Katana 600 (RIP) Posts: 95
|
Quote:
Also that mirror plates don't have free shipping, i think it appears "free" because you are from US, but when i open the link, the shipping is not free, i found another mirror plates, but i don't know if fit that mirror plates are from a zx6r. https://www.ebay.com/itm/Black-Mirro....c100005.m1851 |
|
|
June 12th, 2018, 03:24 PM | #5 | |
ninjette.org certified postwhore
Name: AKA JacRyann
Location: Mesa, AZ
Join Date: Dec 2011 Motorcycle(s): CB125T CBR250R-MC19 CBR250RR-MC22 NSR350R-MC21 VF500F CBR600RR SFV650 VFR750F R1M ST1300PA Valkyrie-F6C Posts: A lot.
MOTY - 2018, MOTM - Nov '17
|
Quote:
ID = inside diameter of handlebar, insert-in mirror goes inside handlebar In my original ebay, it has $23.50 shipping to Mexico. You need plates with 2 holes to properly connect fairing to bracket underneath. ZX6 won't work because it has only one hole |
|
|