October 28th, 2019, 03:34 PM | #1 |
ninjette.org newbie
Name: Ric
Location: Atlanta
Join Date: Oct 2019 Motorcycle(s): 14 Ninja 300 Posts: 8
|
No front brake!!
I have a 2014 EX300a that I have been slowly replacing the brake system components. I have run into a major issue with the replacement Galfer SS line. I could get any hand brake. I took the caliper off and rebuilt it.. new pads!! No brake!! Took caliper off and shot air into it and the pistons popped out. I then put a vacuum bleeder on it and sucked an entire bottle of fluid through it. No brake!! What have I done? Please help !!!
|
|
October 28th, 2019, 03:41 PM | #2 |
ninjette.org guru
Name: Hector
Location: SoCal
Join Date: Sep 2018 Motorcycle(s): 2007 Ninja 250 Posts: 272
|
Maybe the master cylinder piston seal is bad. Same thing happened to my brothers van. The bore of the cylinder was naturally worn, when we pressed the pedal down to bleed the system the piston traveled the full length of the cylinder (down to where it normally doesn't travel and get wear) and the seal got damaged by the more narrow & unworn cylinder diameter.
__________________________________________________
When you see me, it's already too late. |
|
October 28th, 2019, 05:11 PM | #3 | |
ninjette.org member
Name: Sergey
Location: Ontario, GTA
Join Date: Oct 2019 Motorcycle(s): Ninja ZZR250 (EX250H) Posts: 213
|
Quote:
|
|
|
October 28th, 2019, 05:21 PM | #4 |
ninjette.org newbie
Name: Ric
Location: Atlanta
Join Date: Oct 2019 Motorcycle(s): 14 Ninja 300 Posts: 8
|
I hand pumped for ever it seemed like that why I decided to use the vacuum. I understand the air wanting to go up.. there isn’t a bleeder valve on the master so I’m stuck at the caliper.. the brake pads aren’t compressing at all. I’ve lost the whole dang system. I’m great with auto brakes, but this has me stumped!
|
|
October 28th, 2019, 05:51 PM | #5 | |
ninjette.org member
Name: Sergey
Location: Ontario, GTA
Join Date: Oct 2019 Motorcycle(s): Ninja ZZR250 (EX250H) Posts: 213
|
Quote:
Here is what is specified in the manual. First you bleed the master cylinder and only then you bleed the caliper. ○The procedure to bleed the front brake line is as follows. Bleeding the rear brake line is the same as for the front brake. •Remove the reservoir cap [A] and diaphragm. •Fill the reservoir with fresh brake fluid to the upper level line in the reservoir. •Slowly pump the brake lever several times until no air bubbles can be seen rising up through the fluid from the holes at the bottom of the reservoir. ○Bleed the air completely from the master cylinder by this operation. Remove the rubber cap from the bleed valve [A] on the caliper. •Attach a clear plastic hose [B] to the bleed valve, and run the other end of the hose into a container. •Bleed the brake line and the caliper. ○Repeat this operation until no more air can be seen coming out into the plastic hose. 1. Pump the brake lever until it becomes hard, and apply the brake and hold it [A]. 2. Quickly open and close [B] the bleed valve while holding the brake applied. 3. Release the brake [C]. NOTE ○The fluid level must be checked often during the bleeding operation and replenished with fresh brake fluid as necessary. If the fluid in the reservoir runs completely out any time during bleeding, the bleeding operation must be done over again from the beginning since air will have entered the line. ○Tap the brake hose lightly from the caliper to the reservoir for more complete bleeding. |
|
|
October 28th, 2019, 06:01 PM | #6 |
ninjette.org newbie
Name: Ric
Location: Atlanta
Join Date: Oct 2019 Motorcycle(s): 14 Ninja 300 Posts: 8
|
I have done that several times, but I’m not getting any pressure buildup at the lever. I tapped the hose numerous and bled it. Pumped the lever softly and full pulls. Bled the system into a container below the caliper, but still nothing.. I have the lever zipped tied now to see if that’ll help some air release.
|
|
October 29th, 2019, 04:45 AM | #7 |
ninjette.org certified postwhore
Name: AKA JacRyann
Location: Mesa, AZ
Join Date: Dec 2011 Motorcycle(s): CB125T CBR250R-MC19 CBR250RR-MC22 NSR350R-MC21 VF500F CBR600RR SFV650 VFR750F R1M ST1300PA Valkyrie-F6C Posts: A lot.
MOTY - 2018, MOTM - Nov '17
|
You are fighting physics and gravity. Bubbles are rising in system faster than you can bleed fluid. Put brake-caliper HIGHER than master-cylinder until you’ve removed all air. Then put caliper back down/
|
|
October 29th, 2019, 09:09 AM | #8 |
ninjette.org newbie
Name: Ric
Location: Atlanta
Join Date: Oct 2019 Motorcycle(s): 14 Ninja 300 Posts: 8
|
Okay, I took the caliper off and held it higher than the master cylinder and bled until there were no visible bubbles and only fluid coming from bleeder valve. Still no pressure at the lever..
|
|
October 29th, 2019, 01:30 PM | #9 |
ninjette.org certified postwhore
Name: AKA JacRyann
Location: Mesa, AZ
Join Date: Dec 2011 Motorcycle(s): CB125T CBR250R-MC19 CBR250RR-MC22 NSR350R-MC21 VF500F CBR600RR SFV650 VFR750F R1M ST1300PA Valkyrie-F6C Posts: A lot.
MOTY - 2018, MOTM - Nov '17
|
Don't use vacuum-bleeder. Rig up something to hold caliper above master, and get an assistant and do old fashioned way because you need 4-hands:
1. pour new brake-fluid into master so level is topped off. DO NOT LET IT GET LOWER THAN TOP, NOT EVEN HALFWAY! Rotate bars so master reservoir is as flat as possible so you can fill it up as much as possible. 2. loosen bleeder-screw about 1/4-1/3rd turn. Just enough to allow flow. (keep clear hose attached at all time) 3. squeeze brake-lever quickly & firmly, but not fast (about 1/4-sec from open to squeezed). You'll hear squirting noise from master, slightly irregular & rough if there's air. Some should squirt up out of master reservoir, higher level will keep squirt from blowing everywhere. Slow down squeeze if it blows all over. KEEP LEVER SQUEEZED! 4. tighten brake bleeder screw. Did you see any bubbles come out of clear hose when squeezing lever? 5. release brake-lever 6. Go back to #1 You HAVE to alternate between opening bleeder screw, squeezing lever and closing bleeder to ensure that fluid flows one-way and air doesn't get into system. Opening bleeder too much beyond what's needed to enable flow causes bubbles to get in through threads of screw. Speed Bleeders actually makes this process very easy. Last futzed with by DannoXYZ; October 30th, 2019 at 02:43 PM. |
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Rear Brake Doesn't activate Brake Light And DOT3/4 FRONT BRAKE OIL | coelgrim | 2008 - 2012 Ninja 250R Tech Talk | 16 | March 11th, 2013 05:10 PM |
|
|