February 25th, 2012, 11:39 AM | #1 |
ninjette.org member
Name: Guy
Location: Richmond, VA
Join Date: Feb 2012 Motorcycle(s): none Posts: 26
|
What in Hades am I missing??
New to this forum, so if this has been covered before please point me to the thread.
Working on a 2004 that needed the top end rebuilt (new pistons, cylinders honed, etc.). Reassembled everything according to the Manual but it just won't light off. Have checked, and rechecked the cam timing, and as best I can tell everything is spot on. Trying to start/run it using an auxiliary fuel supply. Have spark, have compression, but still no go. What in Hades am I missing. I'm a semi-pro mechanic, so everything done to this bike is nothing new to me, but still... getting really frustrated. Really beginning to question the Manual procedure. TIA |
|
February 25th, 2012, 11:57 AM | #2 |
ninjette.org certified postwhore
Name: Whodat
Location: Ware Is.,MA
Join Date: Jan 2009 Motorcycle(s): I pass the wind! Posts: A lot.
MOTM - Mar '13, Jun '14
|
I'm no mechanic (but I have stayed at Holiday Inn before) but if you have spark and compression I would think it must be fuel that is missing.
__________________________________________________
If everything seems under control; you're just not going fast enough! |
|
February 25th, 2012, 12:08 PM | #3 | |
ninjette.org member
Name: Guy
Location: Richmond, VA
Join Date: Feb 2012 Motorcycle(s): none Posts: 26
|
Quote:
Yeah, have stayed at a few of those myself when I was working as a Cat mechanic in years gone by. With apologies to the owner who frequents this site, the drain screws on the carbs are so buggered up I can't get them out without pulling carbs themselves. What I have done is squirt raw gas down in the vacuum line for the petcock. Did manage to get it to sputter a few times, but it was a "wimpy" sputter and she never took off. I am still questioning the procedure in the Manual itself. That whole cam timing and valve adjustment procedure is rather convoluted, IMHO. Has there been an errata issued regarding that Top End section?? |
|
|
February 25th, 2012, 08:57 PM | #4 |
ninjette.org member
Name: Z
Location: Earth
Join Date: Jun 2010 Motorcycle(s): None Posts: 92
|
How does the carbs look? If they been sitting they will most definitely need to be clean. and the gas in tank flushed.
http://faq.ninja250.org/wiki/General..._won%27t_start Have you check you valves? Even though very small adjustment makes the biggest difference. Make sure your battery fully charge. I had a weak battery would crank but the spark was weak. Kept it hooked on battery to get her running. |
|
February 25th, 2012, 11:10 PM | #5 |
Motorcycle Hypermiler
Name: Vic
Location: Livermore CA
Join Date: Jan 2012 Motorcycle(s): 1999 & 2005 Kawasaki Ninja 250R's Posts: A lot.
|
Since you had the top end apart, check that your camshaft timing is correct.
|
|
February 26th, 2012, 04:21 AM | #6 |
ninjette.org member
Name: Guy
Location: Richmond, VA
Join Date: Feb 2012 Motorcycle(s): none Posts: 26
|
|
|
February 26th, 2012, 06:30 AM | #7 |
Daily Ninjette rider
Name: Hernan
Location: Florida
Join Date: Mar 2011 Motorcycle(s): 2007 Ninja 250 Posts: A lot.
MOTY - 2016, MOTM - Dec '12, Jan '14, Jan '15, May '16
|
I am not aware of any problem with the manual.
Try a car battery and be gentle with your starter; your frustration may overheat it due to repetitive attempts. Right after repair, compression should be low, making start ups difficult. I would verify the intensity and timing of the sparks first. As all mechanics are OK, I would focus on carburation next. All passages and jets very clean and tight rubber boots and vacuum connections. Next would be pushing start (find a down hill), so rpm's go high enough to improve compression and induce combustion. Best
__________________________________________________
Motofool .................................Never ride faster than your guardian angel can fly "Mankind is composed of two sorts of men — those who love and create, and those who hate and destroy. Love is the bond between men, the way to teach and the center of the world." - José Martí |
|
February 26th, 2012, 08:07 AM | #8 | |
ninjette.org member
Name: Guy
Location: Richmond, VA
Join Date: Feb 2012 Motorcycle(s): none Posts: 26
|
Quote:
Battery charge is up there and spins the engine pretty good. Even with the bike's battery, I have been mindful of over-heating the starter. Getting access to a car battery is a thought. I do have a vehicle close to the garage that has a new one, so might give that a try.... again being mindful of extended crank times. In a poke at myself: Have thought about the hill thingy. The first thought is that it would be terribly embarassing that anything coming out of this shop would require a "drastic" measure such as that. I think a couple of neighbor bikers that live on that hill would find that very amusing. The second thought was that I'd have to push back up the hill should it not crank. Even as light as these bikes are, at my age that would be a PITA. Seriously tho', think we'll check the spark timing first, then hit the carbs. I am sure the owner is following this thread and is finding it most amusing. FWIW - this is the reason why the top end needed rebuilt: |
|
|
February 27th, 2012, 12:32 PM | #9 |
ninjette.org member
Name: Guy
Location: Richmond, VA
Join Date: Feb 2012 Motorcycle(s): none Posts: 26
|
A few pix just to have ya'll confirm the cam timing
|
|
February 27th, 2012, 12:53 PM | #10 |
ninjette.org dude
Name: 1 guess :-)
Location: SF Bay Area
Join Date: Jun 2008 Motorcycle(s): '13 Ninja 300 (white, the fastest color!), '13 R1200RT, '14 CRF250L, '12 TT-R125LE Posts: Too much.
Blog Entries: 7
|
Guy - I bumped up the picture sizes in your post so people could see them directly here.
__________________________________________________
Montgomery Street Motorcycle Club / cal24.com / crf250l.org / ninjette.org ninjette.org Terms of Service Shopping for motorcycle parts or equipment? Come here first. The friendliest Ninja 250R/300/400 forum on the internet! (especially Unregistered) |
|
February 27th, 2012, 12:59 PM | #11 |
ninjette.org member
Name: Guy
Location: Richmond, VA
Join Date: Feb 2012 Motorcycle(s): none Posts: 26
|
|
|
February 27th, 2012, 01:01 PM | #12 |
ninjette.org guru
Name: Jason
Location: Houston, TX
Join Date: Nov 2011 Motorcycle(s): 2007 Ninja 250 (sold), '06 Ninja 650R Posts: 455
|
Guy - Did you plug the vacuum line to the petcock?
If you have 33 joints between the marks then your timing is spot on. Also make sure your tensioner is installed correctly, it's bad if it's not (broken valves / intake rockers). Other than that try to hook a fuel source to the carb inlet and plug the vacuum line. If you have compression and spark then remove the carbs and clean them. I have found a pair of vice grips can get the carb drain plugs out. |
|
February 27th, 2012, 01:11 PM | #13 | |
ninjette.org member
Name: Guy
Location: Richmond, VA
Join Date: Feb 2012 Motorcycle(s): none Posts: 26
|
Quote:
Fuel is coming from an auxiliary tank with fresh fuel, altho' the owner has said that he filled up just before the bike took a dump. I did eventually get the bowl drains out, so I know fresh fuel is in there now. Compression on both, newly rebuilt cylinders, cold, is right at 150. The "good" cylinder when the bike was hot pumped a little over 170. I may have no option at this point but to do the "run it down the hill" trick. Gawd, I hate to do that............... |
|
|
February 27th, 2012, 01:17 PM | #14 | |
ninjette.org guru
Name: Jason
Location: Houston, TX
Join Date: Nov 2011 Motorcycle(s): 2007 Ninja 250 (sold), '06 Ninja 650R Posts: 455
|
Quote:
|
|
|
February 27th, 2012, 01:32 PM | #15 | |
ninjette.org member
Name: Guy
Location: Richmond, VA
Join Date: Feb 2012 Motorcycle(s): none Posts: 26
|
Quote:
And apologies to those who don't play with such toys, the last option is to just take it behind the garage and put it out of its misery: |
|
|
February 27th, 2012, 01:41 PM | #16 |
ninjette.org certified postwhore
Name: .
Location: .
Join Date: Feb 2011 Motorcycle(s): . Posts: Too much.
MOTM - Feb '13, Feb '14
|
This may seem really dumb, but just suck a little extra on the vacuum line to make sure the bowls are filled. It always seems to take more sucking on the vacuum line that I expect before the first start-up of the season.
|
|
February 27th, 2012, 01:49 PM | #17 | |
ninjette.org member
Name: Guy
Location: Richmond, VA
Join Date: Feb 2012 Motorcycle(s): none Posts: 26
|
Quote:
. |
|
|
February 27th, 2012, 06:45 PM | #18 |
Daily Ninjette rider
Name: Hernan
Location: Florida
Join Date: Mar 2011 Motorcycle(s): 2007 Ninja 250 Posts: A lot.
MOTY - 2016, MOTM - Dec '12, Jan '14, Jan '15, May '16
|
Did you check the actual level of the fuel inside each bowl?
You can do that with a U shape hose connected to the drains at the bottom of the bowls. That feeder is perfect just like it is. That damaged piston and that "performance" air filter make me suspect of a chronic lean mix condition. It may need bigger jets, who knows? There is tiny gas filter at the carbs inlet nipple, did you check that one?
__________________________________________________
Motofool .................................Never ride faster than your guardian angel can fly "Mankind is composed of two sorts of men — those who love and create, and those who hate and destroy. Love is the bond between men, the way to teach and the center of the world." - José Martí |
|
February 27th, 2012, 08:46 PM | #19 |
ninjette.org member
Name: George
Location: Ottawa, Canada
Join Date: Jun 2011 Motorcycle(s): EX250, C10 Concours Posts: 109
|
Starter fluid?
Did you try starter fluid?
When I got my '89 EX250, the carbs were so clogged, starter fluid was the only way the seller could demonstrate that the motor ran. In case it's carbs, there's an excellent carb cleaning how-to at http://faq.ninja250.org/wiki/How_do_...n_the_carbs%3F. I've recommended it to the Concours folk also. |
|
February 28th, 2012, 04:14 AM | #20 | |
ninjette.org member
Name: Guy
Location: Richmond, VA
Join Date: Feb 2012 Motorcycle(s): none Posts: 26
|
Quote:
I also questioned the air filters when I found the holed piston, but the owner said that carbs had been rejetted. We'll dig deeper a little later. |
|
|
February 28th, 2012, 04:26 AM | #21 | |
ninjette.org member
Name: Guy
Location: Richmond, VA
Join Date: Feb 2012 Motorcycle(s): none Posts: 26
|
Quote:
Nope, no ether yet. I tend to shy away from that stuff. Back in my old Cat days, I ran across a number of diesel engines where it was routinely used. Rather than get their glow plugs working, they just used ether. Over time, those engines became what were known as "Ether Babies." Even during the hot summer mos., using it was the only way you could get them started. Appreciate the link. We'll take a looksee. |
|
|
February 28th, 2012, 07:56 AM | #22 |
ninjette.org member
Name: Guy
Location: Richmond, VA
Join Date: Feb 2012 Motorcycle(s): none Posts: 26
|
I got curious......
and took a look at my (Smugmug) gallery stats.
The cam timing series took 39 hits (as of this a.m.). The holed piston shot took 181. Many, many thanks to all that took a looksee. |
|
February 28th, 2012, 10:07 AM | #23 |
Smoker
Name: Bob
Location: SoCal
Join Date: Dec 2010 Motorcycle(s): Guess.... Posts: 556
|
It has to be the carbs. I've done my share of resurrections, and once I ruled out the electrical side, it always came down to the fuel delivery. Double check that the wires from the harness are solidly connected to the coils. I know it sounds simple and silly, but I had a buddy who just had a running issue that turned out to be the wire going to the coil not being connected.
|
|
February 28th, 2012, 10:29 AM | #24 | |
ninjette.org member
Name: Guy
Location: Richmond, VA
Join Date: Feb 2012 Motorcycle(s): none Posts: 26
|
Quote:
No rest for the weary. |
|
|
February 28th, 2012, 01:37 PM | #25 |
ninjette.org guru
Name: Jason
Location: Houston, TX
Join Date: Nov 2011 Motorcycle(s): 2007 Ninja 250 (sold), '06 Ninja 650R Posts: 455
|
This does not have bearing on your current problem but....
What spark plugs are you running? |
|
February 28th, 2012, 01:48 PM | #26 |
ninjette.org member
Name: Guy
Location: Richmond, VA
Join Date: Feb 2012 Motorcycle(s): none Posts: 26
|
It could, but I'm not sure at the moment. I did look at them and should have made a note what they were, but didn't. They're in the bike now, but will pull them out shortly and see.
|
|
February 28th, 2012, 04:00 PM | #27 | |
ninjette.org guru
Name: Jason
Location: Houston, TX
Join Date: Nov 2011 Motorcycle(s): 2007 Ninja 250 (sold), '06 Ninja 650R Posts: 455
|
Quote:
I use NGK. http://faq.ninja250.org/wiki/Changin...rands_to_avoid |
|
|
February 28th, 2012, 10:09 PM | #28 |
ninjette.org dude
Name: 1 guess :-)
Location: SF Bay Area
Join Date: Jun 2008 Motorcycle(s): '13 Ninja 300 (white, the fastest color!), '13 R1200RT, '14 CRF250L, '12 TT-R125LE Posts: Too much.
Blog Entries: 7
|
This page is still pulling directly from the smugmug galleries (they are just live links), so every time that this thread is viewed, the stats go up on the smugmug side.
__________________________________________________
Montgomery Street Motorcycle Club / cal24.com / crf250l.org / ninjette.org ninjette.org Terms of Service Shopping for motorcycle parts or equipment? Come here first. The friendliest Ninja 250R/300/400 forum on the internet! (especially Unregistered) |
|
February 29th, 2012, 07:05 AM | #29 |
ninjette.org member
Name: Guy
Location: Richmond, VA
Join Date: Feb 2012 Motorcycle(s): none Posts: 26
|
Okay, I'm stopping until I get a hold of the owner.
Have used the line on the drain to check bowl fuel levels before, and did that on these prior to pulling the carbs. They were spot on.
Then the fun began when I started taking them apart. Many of the bowl screws were buggered up, but managed to break them free and got the bowls off. Normally I pull the pilot jets first, but they were so tight they wouldn't budge, Decided to them pull the needle jet (tube) with main jets still attached. These too were extremely and needed to use a 6-point box wrench to get them free. This is what I found on both carbs: Considering the long ported shank on the pilot jets, I can only assume they are distorted too. Then pulled the caps to check the diaphragms. This what I found on one of them: Mixture idle needles looked okay and were both turned out an equal amount. This is a case of being ham-fisted in all the wrong places. |
|
February 29th, 2012, 07:52 AM | #30 |
ninjette.org guru
Name: Jason
Location: Houston, TX
Join Date: Nov 2011 Motorcycle(s): 2007 Ninja 250 (sold), '06 Ninja 650R Posts: 455
|
Well there's your problem....
I don't even know how that could happen. |
|
February 29th, 2012, 08:05 AM | #31 |
ninjette.org member
Name: Guy
Location: Richmond, VA
Join Date: Feb 2012 Motorcycle(s): none Posts: 26
|
|
|
February 29th, 2012, 08:51 AM | #32 |
ninjette.org guru
Name: Jason
Location: Houston, TX
Join Date: Nov 2011 Motorcycle(s): 2007 Ninja 250 (sold), '06 Ninja 650R Posts: 455
|
How much are replacement parts going to cost?
If the diaphragms arn't salvagable, it might be easier to buy a set of used carbs. |
|
February 29th, 2012, 09:43 AM | #33 | |
ninjette.org member
Name: Guy
Location: Richmond, VA
Join Date: Feb 2012 Motorcycle(s): none Posts: 26
|
Quote:
. |
|
|
February 29th, 2012, 01:57 PM | #34 |
no such thing as ninjette
Name: AP
Location: L.A., CA
Join Date: May 2011 Motorcycle(s): (2) 1987 EX250E2, 1989 EL250B3, 1991 EL250E1, (3) 2005 EX250F19, 2007 EX250F7F, soon to add more.. Posts: 26
|
|
|
February 29th, 2012, 02:04 PM | #35 |
ninjette.org member
Name: Guy
Location: Richmond, VA
Join Date: Feb 2012 Motorcycle(s): none Posts: 26
|
Gotta laugh; give the man the Kewpie doll!!!
I just got off the phone with him about a half hour ago. He's seen/read the thread, but had NO IDEA his bike was the subject of my query. Fortunately, he does have a set of carbs. Old, may be gummed up, but have to be danged sure better of what I found in the ones that came off his bike. I can deal with gummed, but not distorted/bent needle jets. He's gonna get them this w/e, and we'll go from there. . |
|
February 29th, 2012, 09:55 PM | #36 |
Milkshake Drinker
Name: Skippii
Location: Richmond, Va
Join Date: Aug 2011 Motorcycle(s): 2007 Orange DRZ400-S, 2005 Ninja 250 & Custom Thundercunt Dirt Chopper Posts: A lot.
|
I can't believe someone noticed this before I did.
I'd read the first 10 posts or so on my phone (which didn't show pictures) but didn't have anything to suggest, then I never came back to it. Been busy at work lately where I tend do to a lot of my interwebbing...never even occurred to me y'all might be discussing my bike (which, btw, is a 2005, not a 2004...that's my defense!) Anyway, back to the subject at hand.... These carbs were off my 2006 Ninja 250, which I'd spent hours carefully jetting with an exhaust gas analyzer. I'd replaced the main jets, shimmed the needles and adjusted the idle screws, but I never removed the needle slots--the parts which appear to be slightly butchered. I believe I was the second owner of that bike, and it had never been modified, so either they got that way on their own inside the carbs or they came from the factory like that--neither of which really seems likely. Anyway, after I got rid of that bike I kept the carbs and the K&N pods, and when I got the 2005 just stuck those carbs and pods on together. Here's what confuses the heck out of me: Those carbs have been on this bike in that condition for about 12,000 miles, and on the previous bike for 5,000 miles, and I've never had any problems with them. The only time they were ever opened in the last 3 years was at the end of last year. I was doing a valve check/adjustment, and noticed that my engine seemed to be running a little rich, so while I was working on the engine, I asked my friend who was helping me with little things (mostly holding things, fetching me a drink, grabbing the appropriate allan wrench, etc) to check how many washers I'd used under the needles. He opened up the tops, counted the washers (I believe just one, IIRC) and I said to leave them as they were rather than risk going lean, and he closed them back up. I'm guessing he may have pinched the diaphragm a bit when he closed them...there was a very slight tear in one of them before, but nothing like in that picture. So, the real question I have is this: if these carbs have worked flawlessly in this condition for the past 17,000 miles, why would it only make such a huge difference now with the new pistons installed? Even the day after it broke down it still fired up almost immediately on one cylinder when I went back to check on it by the side of the road (for about 2 seconds--I hit the kill switch as soon as I saw the green coolant shoot out the left side.)
__________________________________________________
"What a sweetheart."- ninja_sleeper to me |
|
March 1st, 2012, 05:51 AM | #37 | |
ninjette.org member
Name: Guy
Location: Richmond, VA
Join Date: Feb 2012 Motorcycle(s): none Posts: 26
|
Quote:
It's just as much a mystery to me, which is why I initiated this thread to begin with. I wanted other eyes to check my work. . |
|
|
March 2nd, 2012, 09:36 PM | #38 | |
Milkshake Drinker
Name: Skippii
Location: Richmond, Va
Join Date: Aug 2011 Motorcycle(s): 2007 Orange DRZ400-S, 2005 Ninja 250 & Custom Thundercunt Dirt Chopper Posts: A lot.
|
Quote:
In all seriousness, I was originally thinking about doing all the work myself...I'm VERY glad I didn't do that--It's comforting to know someone with a lot more experience is tackling the project. I'm heading over to pick up the carbs on Monday (my 'weekend') and I'll drop them off on my way to work Wednesday.
__________________________________________________
"What a sweetheart."- ninja_sleeper to me |
|
|
March 3rd, 2012, 04:31 AM | #39 | |
ninjette.org member
Name: Guy
Location: Richmond, VA
Join Date: Feb 2012 Motorcycle(s): none Posts: 26
|
Quote:
Looking forward to getting them. And yes, I'm a little nervous too, but think we have all the bases covered and enough folks have eyed where things are now to have spotted something that may be amiss. .
__________________________________________________
Garage Project: http://gbyoung2.smugmug.com/Family/G...1686385_MTJSCh |
|
|
March 3rd, 2012, 10:20 PM | #40 |
Milkshake Drinker
Name: Skippii
Location: Richmond, Va
Join Date: Aug 2011 Motorcycle(s): 2007 Orange DRZ400-S, 2005 Ninja 250 & Custom Thundercunt Dirt Chopper Posts: A lot.
|
Well, I don't think there's any question that there's something amiss with those carbs!
__________________________________________________
"What a sweetheart."- ninja_sleeper to me |
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
What else am I missing???? | userjh160 | General Motorcycling Discussion | 23 | October 2nd, 2012 08:50 AM |
my friend has gone missing | hoodadooda | Off-Topic | 11 | January 15th, 2012 12:40 AM |
Help with missing bolt | dk58 | 2008 - 2012 Ninja 250R Tech Talk | 22 | May 11th, 2011 07:07 PM |
missing screw? | backinthesaddleagain | General Motorcycling Discussion | 5 | January 10th, 2010 10:46 PM |
Something's missing. | tinng321 | General Motorcycling Discussion | 15 | June 25th, 2009 01:00 PM |
|
|