June 12th, 2013, 06:16 AM | #41 | |
Daily Ninjette rider
Name: Hernan
Location: Florida
Join Date: Mar 2011 Motorcycle(s): 2007 Ninja 250 Posts: A lot.
MOTY - 2016, MOTM - Dec '12, Jan '14, Jan '15, May '16
|
Quote:
I forgot to tell you that the test for the switch had to be done with the engine running. So, we cannot rule the left hand switch as good yet. The link of post #11 explains why you will not see juice at those wires until after the engine is rotating.
__________________________________________________
Motofool .................................Never ride faster than your guardian angel can fly "Mankind is composed of two sorts of men — those who love and create, and those who hate and destroy. Love is the bond between men, the way to teach and the center of the world." - José Martí Last futzed with by Motofool; June 12th, 2013 at 07:38 AM. |
|
|
June 12th, 2013, 09:16 AM | #42 | |
ninjette.org guru
Name: andrew
Location: oakdale california
Join Date: Nov 2011 Motorcycle(s): 2012 ninja 250 Posts: 296
|
Quote:
also when I tested the voltage in my last post. I got a zero reading when I had the positive on the yellow/blue wire leading to the relay and negative on the negative battery. Think my headlight relay is bad / dead? |
|
|
June 12th, 2013, 10:17 AM | #43 |
Daily Ninjette rider
Name: Hernan
Location: Florida
Join Date: Mar 2011 Motorcycle(s): 2007 Ninja 250 Posts: A lot.
MOTY - 2016, MOTM - Dec '12, Jan '14, Jan '15, May '16
|
Sorry for assuming that the engine was off
If the high beam is working, the relay must be working (at least for that bulb). The relay is nothing more than a switch that turns on when voltage is applied to the internal coil. The reading in the battery is low, but the lights should shine some at least. Let me think what tests we can do with the voltmeter next.
__________________________________________________
Motofool .................................Never ride faster than your guardian angel can fly "Mankind is composed of two sorts of men — those who love and create, and those who hate and destroy. Love is the bond between men, the way to teach and the center of the world." - José Martí |
|
June 12th, 2013, 10:25 AM | #44 | |
ninjette.org guru
Name: andrew
Location: oakdale california
Join Date: Nov 2011 Motorcycle(s): 2012 ninja 250 Posts: 296
|
Quote:
just to state, no beams are working at all at this point, and the blue light on the dash for high beam doesnt work either. For awhile only my high beam would come after the bike was running for 10 mins. If I shut it off and turned it back on after that chances are the high beam would not come back on instantly. My low beam hasn't worked for a while now. as of right now no beam will turn on. And my battery voltage being low is crazy because I just bought a new battery I wonder whats going on with that. |
|
|
June 12th, 2013, 10:39 AM | #45 |
Fix It Till Ya Break It
Name: Asspyre
Location: T.Dot
Join Date: Oct 2011 Motorcycle(s): 08 250RRrrrr Posts: 623
|
check the red wire coming out of the diode pack, should be a voltage when running on that line..... I think, will need to verify when I get home
|
|
June 12th, 2013, 10:57 AM | #46 | |
ninjette.org guru
Name: andrew
Location: oakdale california
Join Date: Nov 2011 Motorcycle(s): 2012 ninja 250 Posts: 296
|
Quote:
Does it mean anything since I got a 0 reading going to my relay? Does that mean the relay is bad? the diode pack is the thing that sits over the battery correct? |
|
|
June 12th, 2013, 11:09 AM | #47 |
Fix It Till Ya Break It
Name: Asspyre
Location: T.Dot
Join Date: Oct 2011 Motorcycle(s): 08 250RRrrrr Posts: 623
|
yes, the yellow wire that goes into the diode pack is from the stator, when the bike is started it feeds power thru the diode into the red wire which powers the coil for the headlight relay, so that means that if there is voltage at the red wire when the bike is running, we can assume the relay is at fault, if there is no power, then possible bad diode or bad stator/shorted stator since your running voltage is so low.
I'm doing write up on replacing/test stator and voltage regulator which I'll post when I get home |
|
June 12th, 2013, 11:13 AM | #48 | |
Daily Ninjette rider
Name: Hernan
Location: Florida
Join Date: Mar 2011 Motorcycle(s): 2007 Ninja 250 Posts: A lot.
MOTY - 2016, MOTM - Dec '12, Jan '14, Jan '15, May '16
|
Quote:
1) Ground the negative leg of your voltmeter. 2) Turn the ignition key to the on position, but don't start the engine. 3) With the positive leg of the voltmeter, touch the naked metal dots on the top of the fuse #5 (headlight / 10 A / gray wire) 4) If volts' reading there (value does not matter), follow that grey wire up to the headlight relay. That relay has our gray wire, one blue/yellow, one yellow/red and one red. We will need to measure the voltage at the yellow/red and at the blue/yellow. 5) Start the engine. 6) The yellow/red and the gray wires should have measurable voltage with the engine rotating.
__________________________________________________
Motofool .................................Never ride faster than your guardian angel can fly "Mankind is composed of two sorts of men — those who love and create, and those who hate and destroy. Love is the bond between men, the way to teach and the center of the world." - José Martí |
|
|
June 12th, 2013, 11:45 AM | #49 | ||
ninjette.org guru
Name: andrew
Location: oakdale california
Join Date: Nov 2011 Motorcycle(s): 2012 ninja 250 Posts: 296
|
Quote:
if there is no power on the red wire can we assume its either a bad diode or a faulty stator (this sounds bad hope it's not that haha). was I correct on checking running voltage by putting the positive side of the tester on the positive side of the battery and the negative part of the tester on the negative side of the battery? and checking that reading? Quote:
I kind of did step #4 last night. At the blue and yellow I got a 0 reading with the bike running. Will do everything you mentioned this evening once I get a hold of my tester. Thanks again guys. I'm about ready to take this guy to the shop! But I like learning even though it is kind of stressful |
||
|
June 12th, 2013, 11:52 AM | #50 | |
Daily Ninjette rider
Name: Hernan
Location: Florida
Join Date: Mar 2011 Motorcycle(s): 2007 Ninja 250 Posts: A lot.
MOTY - 2016, MOTM - Dec '12, Jan '14, Jan '15, May '16
|
Quote:
However, with engine rotating, blue/yellow should measure close to 12v. You are welcome No, no, we are almost there !!! It is either the relay of the diode.
__________________________________________________
Motofool .................................Never ride faster than your guardian angel can fly "Mankind is composed of two sorts of men — those who love and create, and those who hate and destroy. Love is the bond between men, the way to teach and the center of the world." - José Martí |
|
|
June 12th, 2013, 12:00 PM | #51 | |
ninjette.org guru
Name: andrew
Location: oakdale california
Join Date: Nov 2011 Motorcycle(s): 2012 ninja 250 Posts: 296
|
Quote:
I'll test tonight and let you guys know. Ty |
|
|
June 12th, 2013, 12:14 PM | #52 |
ninjette.org member
Name: Jon
Location: California
Join Date: May 2013 Motorcycle(s): 2005 Ninja 250 Posts: 151
|
Keep us posted and maybe do a write up for your specific problem and how it was solved. it is unlikely you are the only one =P
Thanks for the thread, bookmarked. |
|
June 12th, 2013, 02:11 PM | #53 |
ninjette.org guru
Name: andrew
Location: oakdale california
Join Date: Nov 2011 Motorcycle(s): 2012 ninja 250 Posts: 296
|
I can and deff will do a write up of everything I've done and went through once I actually figure out!
|
|
June 12th, 2013, 04:09 PM | #54 |
Daily Ninjette rider
Name: Hernan
Location: Florida
Join Date: Mar 2011 Motorcycle(s): 2007 Ninja 250 Posts: A lot.
MOTY - 2016, MOTM - Dec '12, Jan '14, Jan '15, May '16
|
Andrew,
I am at home and ready for the final test
__________________________________________________
Motofool .................................Never ride faster than your guardian angel can fly "Mankind is composed of two sorts of men — those who love and create, and those who hate and destroy. Love is the bond between men, the way to teach and the center of the world." - José Martí |
|
June 12th, 2013, 10:05 PM | #55 |
ninjette.org guru
Name: andrew
Location: oakdale california
Join Date: Nov 2011 Motorcycle(s): 2012 ninja 250 Posts: 296
|
alright so i finally got to do some tests.
again i tested the yellow/blue wire coming out of the relay and i actually got a 1 reading. then i tested the blue/yellow wire going into the diode and also got a 1 reading. i deff got a zero yesterday. -pic 1 and2 finally i tested both of the red wires coming out of the diode and i got a 2 reading. - pic 4 the last pic reading a zero is just to make sure i have this thing on the correct setting lol. -pic 5 Last futzed with by walty87; June 13th, 2013 at 12:07 AM. |
|
June 13th, 2013, 06:41 AM | #56 | ||
Daily Ninjette rider
Name: Hernan
Location: Florida
Join Date: Mar 2011 Motorcycle(s): 2007 Ninja 250 Posts: A lot.
MOTY - 2016, MOTM - Dec '12, Jan '14, Jan '15, May '16
|
Quote:
What about the other tests? Quote:
__________________________________________________
Motofool .................................Never ride faster than your guardian angel can fly "Mankind is composed of two sorts of men — those who love and create, and those who hate and destroy. Love is the bond between men, the way to teach and the center of the world." - José Martí |
||
|
June 13th, 2013, 08:31 AM | #57 | ||
ninjette.org guru
Name: andrew
Location: oakdale california
Join Date: Nov 2011 Motorcycle(s): 2012 ninja 250 Posts: 296
|
Quote:
Quote:
sorry i was too tired to finish all of that last night.. did those right now though 1.) By grounding the bike negative i'm putting it on the negative side of the battery. Whenever I ground the negative to the frame of the bike I get zero readings on all tests. Hope thats ok. 3.) Touched the bottom of grey wire on fuse#5 headlight / 10a with the positive side and the negative on the bike negative battery with the bike off and got an 11.5 reading. When i touched the top plastic red part of the fuse i got a 0. (i did switch the fuse with a spare already). Not sure which way you wanted me to do it. 4.)i got a 11.5 reading at the blue/yellow wire with bike off. got a zero at the red/yellow wire with bike off 6.)gray had 11.5 reading while the bike was on at the headlight relay. the yellow and red wire had a zero reading with the bike on. Last futzed with by walty87; June 13th, 2013 at 09:54 AM. |
||
|
June 13th, 2013, 10:01 AM | #58 | |
Daily Ninjette rider
Name: Hernan
Location: Florida
Join Date: Mar 2011 Motorcycle(s): 2007 Ninja 250 Posts: A lot.
MOTY - 2016, MOTM - Dec '12, Jan '14, Jan '15, May '16
|
Quote:
__________________________________________________
Motofool .................................Never ride faster than your guardian angel can fly "Mankind is composed of two sorts of men — those who love and create, and those who hate and destroy. Love is the bond between men, the way to teach and the center of the world." - José Martí |
|
|
June 13th, 2013, 10:19 AM | #60 |
Daily Ninjette rider
Name: Hernan
Location: Florida
Join Date: Mar 2011 Motorcycle(s): 2007 Ninja 250 Posts: A lot.
MOTY - 2016, MOTM - Dec '12, Jan '14, Jan '15, May '16
|
OK, everything cool so far.
Make a U-shape with a heavy wire to make a bridge. Next, lets start the engine and measure the same wires. Yellow-red should have close to zero. Grey, blue-yellow and red should have close to 12v.
__________________________________________________
Motofool .................................Never ride faster than your guardian angel can fly "Mankind is composed of two sorts of men — those who love and create, and those who hate and destroy. Love is the bond between men, the way to teach and the center of the world." - José Martí |
|
June 13th, 2013, 10:26 AM | #61 | |
ninjette.org guru
Name: andrew
Location: oakdale california
Join Date: Nov 2011 Motorcycle(s): 2012 ninja 250 Posts: 296
|
Quote:
With the engine on the yellow blue coming out of the relay only has 1 or .1 on it. Is that coming in or out? Think it's the relay?? |
|
|
June 13th, 2013, 10:38 AM | #62 | |
Daily Ninjette rider
Name: Hernan
Location: Florida
Join Date: Mar 2011 Motorcycle(s): 2007 Ninja 250 Posts: A lot.
MOTY - 2016, MOTM - Dec '12, Jan '14, Jan '15, May '16
|
Quote:
What about the red wire? With the engine running, jump the grey and the blue-yellow wires at the relay (use a heavy gauge wire) and check if one of the lights come on while you do that (Don't worry, nothing will be damaged because what you will do with the jumper is what the relay does automatically). If so, switch between hi and low beam and see if both work properly. Then, with the bridge still there and the headlight on, stop the engine with the kill switch, leaving the key-switch on and see what happen to the lights (stay on or turn off). I am assuming that you have new bulbs in place now.
__________________________________________________
Motofool .................................Never ride faster than your guardian angel can fly "Mankind is composed of two sorts of men — those who love and create, and those who hate and destroy. Love is the bond between men, the way to teach and the center of the world." - José Martí |
|
|
June 13th, 2013, 12:26 PM | #63 | |
ninjette.org guru
Name: andrew
Location: oakdale california
Join Date: Nov 2011 Motorcycle(s): 2012 ninja 250 Posts: 296
|
Quote:
Yes new bulbs. And the red wire had voltage. Want to say 11.5 |
|
|
June 13th, 2013, 12:47 PM | #64 | |
Daily Ninjette rider
Name: Hernan
Location: Florida
Join Date: Mar 2011 Motorcycle(s): 2007 Ninja 250 Posts: A lot.
MOTY - 2016, MOTM - Dec '12, Jan '14, Jan '15, May '16
|
Quote:
Important: See what the lights do and switch Lo-Hi-Lo
__________________________________________________
Motofool .................................Never ride faster than your guardian angel can fly "Mankind is composed of two sorts of men — those who love and create, and those who hate and destroy. Love is the bond between men, the way to teach and the center of the world." - José Martí |
|
|
June 13th, 2013, 01:36 PM | #65 |
ninjette.org guru
Name: andrew
Location: oakdale california
Join Date: Nov 2011 Motorcycle(s): 2012 ninja 250 Posts: 296
|
|
|
June 13th, 2013, 01:40 PM | #66 |
Daily Ninjette rider
Name: Hernan
Location: Florida
Join Date: Mar 2011 Motorcycle(s): 2007 Ninja 250 Posts: A lot.
MOTY - 2016, MOTM - Dec '12, Jan '14, Jan '15, May '16
|
OK, I am ahead of time, since I live in Florida.
If the lights get on and the switch changes Hi and Low, then the contacts of the relay stay open and the relay needs to be replaced. If the lights turn off after you stop the engine (with the kill switch), then, the diode B is bad as well.
__________________________________________________
Motofool .................................Never ride faster than your guardian angel can fly "Mankind is composed of two sorts of men — those who love and create, and those who hate and destroy. Love is the bond between men, the way to teach and the center of the world." - José Martí |
|
June 13th, 2013, 08:49 PM | #67 | |
ninjette.org guru
Name: andrew
Location: oakdale california
Join Date: Nov 2011 Motorcycle(s): 2012 ninja 250 Posts: 296
|
Quote:
I think we made some progress!!!! Jumped the relay with some wire as mentioned above. When I turned the key into the on position the lights came on! Both low and then the high beam worked by flipping the switch! I started the bike and they stayed on, and then when i killed the bike with the kill switch they stayed on! Assuming this is a bad relay!? About to order one!? Now for the time being is it safe to use this bypass on the relay switch for the headlights so I can ride in the amazing weather in central cali!? Or should I just be patient and wait? |
|
|
June 14th, 2013, 06:44 AM | #68 | |
Daily Ninjette rider
Name: Hernan
Location: Florida
Join Date: Mar 2011 Motorcycle(s): 2007 Ninja 250 Posts: A lot.
MOTY - 2016, MOTM - Dec '12, Jan '14, Jan '15, May '16
|
Quote:
Now we know that the only bad part is the relay. Sorry that I did mislead you to the left handler switch, the fact of one bulb only turning on confused me. The diodes are good. I am not sure if something bad will happen by starting the engine and turning the lights on at once. The purpose of the system is to feed the starter motor only with the battery, and turn the lights on only after the starter is off and the alternator is feeding the lights and anything else. I would give it a try and see if no fuse is blown. There is a plastic clip for jumping cables that should be available at autoparts and which schematic I have attached. Whatever method of by-passing the relay you choose, try a firm connection and check that it is not too hot after some minutes of having the lights on. Since we know that the relay is bad, there is an additional test to do and it is checking the voltage of the yellow-red wire while the engine is working. I know that you tested before (test #6 above), but I am not sure if you measured with the engine working or just the key switch in the on position. It should be zero or very small. That ensures that the coil of the relay is good and that the starter motor is not draining the battery after the engine is running.
__________________________________________________
Motofool .................................Never ride faster than your guardian angel can fly "Mankind is composed of two sorts of men — those who love and create, and those who hate and destroy. Love is the bond between men, the way to teach and the center of the world." - José Martí |
|
|
June 14th, 2013, 08:21 AM | #69 | |
ninjette.org guru
Name: andrew
Location: oakdale california
Join Date: Nov 2011 Motorcycle(s): 2012 ninja 250 Posts: 296
|
Quote:
I want to say when I was doing testing I was always doing it with the engine running and with just the key on and engine not running. Also I want to say I got 1/ .1 or 2/ .2 on the yellow / red wire. Will confirm tonight. to confirm the relay is part number 27002: RELAY-ASSY or is it 27002A: RELAY-ASSY or neither? anyways thanks again for all the help! Once I get everything together and running for sure once I get the parts I will make a right up of everything i've done! Thanks a lot everyone! I learned a lot about the bikes electrical system |
|
|
June 14th, 2013, 10:34 AM | #70 |
Daily Ninjette rider
Name: Hernan
Location: Florida
Join Date: Mar 2011 Motorcycle(s): 2007 Ninja 250 Posts: A lot.
MOTY - 2016, MOTM - Dec '12, Jan '14, Jan '15, May '16
|
I cannot confirm the part number, since I have a pre-gen.
Your relay should have some label under that rubber protector. You are welcome, Andrew
__________________________________________________
Motofool .................................Never ride faster than your guardian angel can fly "Mankind is composed of two sorts of men — those who love and create, and those who hate and destroy. Love is the bond between men, the way to teach and the center of the world." - José Martí |
|
June 14th, 2013, 11:15 AM | #71 | |
ninjette.org guru
Name: andrew
Location: oakdale california
Join Date: Nov 2011 Motorcycle(s): 2012 ninja 250 Posts: 296
|
Quote:
@alex.s you have any idea? |
|
|
June 15th, 2013, 01:14 PM | #72 |
ninjette.org guru
Name: andrew
Location: oakdale california
Join Date: Nov 2011 Motorcycle(s): 2012 ninja 250 Posts: 296
|
@Motofool @%1;
Guys sorry for the mention but I'm in a bad spot. Took the ninja to work today. On the way here my headlights still aren't working (relay in the mail), but my rpm tach meter stopped working. Once I turned the bike off, it now won't turn on.. I just get the clicking sound like my battery is dead. Seems like my battery is dead. And it's brand new. Now the battery I got the guy at auto some said I didn't hav to put the stuff In it or I'm no expert but I can't think of reason why it wouldn't. I'm going to try it maybe, unless someone else chimes in!? charge it, I ill try and find a link to the brand. Maybe it does need a charge? |
|
June 15th, 2013, 01:25 PM | #73 | |
Daily Ninjette rider
Name: Hernan
Location: Florida
Join Date: Mar 2011 Motorcycle(s): 2007 Ninja 250 Posts: A lot.
MOTY - 2016, MOTM - Dec '12, Jan '14, Jan '15, May '16
|
Quote:
You can start the bike and return home. http://faq.ninja250.org/wiki/How_to_...attery_is_dead http://faq.ninja250.org/wiki/How_to_...ike_from_a_car http://faq.ninja250.org/wiki/My_batt...art_my_bike%3F
__________________________________________________
Motofool .................................Never ride faster than your guardian angel can fly "Mankind is composed of two sorts of men — those who love and create, and those who hate and destroy. Love is the bond between men, the way to teach and the center of the world." - José Martí |
|
|
June 15th, 2013, 01:55 PM | #74 | |
ninjette.org guru
Name: andrew
Location: oakdale california
Join Date: Nov 2011 Motorcycle(s): 2012 ninja 250 Posts: 296
|
Quote:
|
|
|
June 15th, 2013, 02:12 PM | #75 | |
Daily Ninjette rider
Name: Hernan
Location: Florida
Join Date: Mar 2011 Motorcycle(s): 2007 Ninja 250 Posts: A lot.
MOTY - 2016, MOTM - Dec '12, Jan '14, Jan '15, May '16
|
Quote:
Sorry about your problem, hope you can make it back home safely.
__________________________________________________
Motofool .................................Never ride faster than your guardian angel can fly "Mankind is composed of two sorts of men — those who love and create, and those who hate and destroy. Love is the bond between men, the way to teach and the center of the world." - José Martí |
|
|
June 15th, 2013, 03:57 PM | #76 |
ninjette.org guru
Name: andrew
Location: oakdale california
Join Date: Nov 2011 Motorcycle(s): 2012 ninja 250 Posts: 296
|
Would my battery being dead be the cause of the rpm tach not working?
Thanks motofool |
|
June 15th, 2013, 04:06 PM | #77 | |
Long Time Rider
Name: Blue
Location: Charlotte, NC
Join Date: Sep 2010 Motorcycle(s): 2009 Kawasaki Ninja 250R Posts: A lot.
|
Quote:
- charge the battery if the motor fails to start or the starter relay makes a clicking noise ~ http://www.ninjette.org/wiki/Battery |
|
|
June 15th, 2013, 07:30 PM | #78 | |
ninjette.org guru
Name: andrew
Location: oakdale california
Join Date: Nov 2011 Motorcycle(s): 2012 ninja 250 Posts: 296
|
Quote:
Pushed started the bike and it started up no problem and was running just fine when i got off of work. I traveled about 2 miles and got to an intersection. When I went to take off from that intersection the bike lost power and died. Attempted to push start the bike and iit started but lost power and died again. Called my gf to bring my truck to get me. Its not starting obviously. Maybe I do have a loose battery cable i hope. Going to hook my battery on a charger tonight and I hope that's what this issue is. Argh |
|
|
June 15th, 2013, 08:33 PM | #79 |
Daily Ninjette rider
Name: Hernan
Location: Florida
Join Date: Mar 2011 Motorcycle(s): 2007 Ninja 250 Posts: A lot.
MOTY - 2016, MOTM - Dec '12, Jan '14, Jan '15, May '16
|
Sorry, Andrew
__________________________________________________
Motofool .................................Never ride faster than your guardian angel can fly "Mankind is composed of two sorts of men — those who love and create, and those who hate and destroy. Love is the bond between men, the way to teach and the center of the world." - José Martí |
|
June 15th, 2013, 09:02 PM | #80 |
Fix It Till Ya Break It
Name: Asspyre
Location: T.Dot
Join Date: Oct 2011 Motorcycle(s): 08 250RRrrrr Posts: 623
|
check your running voltage, it should be no less than 12.3v at idle. if its lower:
find this connector on the right side: unplug it and hook up your tester to the plug with three yellow wires: switch your tester to ohms and measure ( my tester is at .6 ohms with two leads touching each other, my reading it .9 - so the stator has .3 ohms resistance). I believe the spec is between 0.05 and .6 ohms for the stator, check all three yellow wires for the same resistance: now check the each yellow wire for short to ground by putting the negative lead on battery negative and positive to each yellow wire, any reading means a short to ground, it should read nil: Now switch the tester to AC volt reading, leave the test leads in the connector, start bike and bring engine up to 4,000 rpm (using the choke helps if you only have 2 hands). The output from stator should be around 40V A/C (when warm), check to make sure that they're about the same for all three yellow wires: set your test leads: voltage @ 4,000 rpm: if the output is lower, stator is bad, if much higher, voltage regulator is damaged. if no reading, sell bike as "old lady driven" |
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Fairing above headlight problem? | MCNinja18 | 2013 - 2017 Ninja 300 Tech Talk | 9 | July 27th, 2014 01:32 PM |
Headlight problem | puma22 | 2008 - 2012 Ninja 250R Tech Talk | 10 | August 16th, 2013 10:48 AM |
Intermittent Headlight Problem | n4mwd | 1986 - 2007 Ninja 250R Tech Talk | 3 | December 25th, 2012 05:18 PM |
headlight problem | Moto126 | 2008 - 2012 Ninja 250R Tech Talk | 2 | May 20th, 2012 05:48 AM |
Headlight Problem | Chamus57 | 2008 - 2012 Ninja 250R Tech Talk | 7 | September 29th, 2009 02:53 PM |
|
|