July 13th, 2014, 04:40 AM | #1 |
ninjette.org member
Name: Amy
Location: Northeast Ohio
Join Date: Jul 2014 Motorcycle(s): 2005 Kawasaki Ninja 250 Posts: 124
|
Spark plug tool - check/change plugs
I would really like to check/change my spark plugs today. Does anyone live anywhere near Niles Ohio that can let me perhaps borrow their spark plug tool or even recommend an alternative option for the plug removal using a "regular" spark plug wrench? My husband has one but I don't think it would work given the tight angle to reach the plugs. I really don't want to take the tank off - that concerns me.
__________________________________________________
Present: 05 Kawasaki Ninja 250 Past: 02 Honda Rebel, 09 CFMoto Glory 150 |
|
July 13th, 2014, 04:55 AM | #2 |
ninjette.org member
Name: Amy
Location: Northeast Ohio
Join Date: Jul 2014 Motorcycle(s): 2005 Kawasaki Ninja 250 Posts: 124
|
Found a spark plug tool - looks just like the Ninja one
My husband has a spark plug tool that swings just like the one that comes in the tool kit (that I didn't get with my bike argh). It has a long skinny reach arm and a swivelling 13/16 spark plug socket. Is that the right "size" to get a hold of the plug?
__________________________________________________
Present: 05 Kawasaki Ninja 250 Past: 02 Honda Rebel, 09 CFMoto Glory 150 |
|
July 13th, 2014, 05:48 AM | #3 |
Que Buenos Son!!!
Name: Ryan
Location: Grovetucky, OH
Join Date: Jun 2012 Motorcycle(s): Aprilia Shiver 750, Husaberg FE 450, Ninja 300 (sold), xr100 Posts: A lot.
MOTM - Nov '14
|
If I remember correctly a 5/8" plug socket is what you need for the pre-gen. It's been a while since I've messed with the plugs on mine so I'm not certain.
But why are you so against removing the gas tank? It's super easy on these bikes, six screws and two lines I think, only takes about 5 minutes. Seems a lot easier to me than trying to fish out the sparks plugs with a tool.
__________________________________________________
Don't do something because it's easy,.. Do it because it's not! If you aren't going forward, then you're falling behind. "Drive it like you stole it"!!! |
|
July 13th, 2014, 05:51 AM | #4 |
ninjette.org member
Name: Amy
Location: Northeast Ohio
Join Date: Jul 2014 Motorcycle(s): 2005 Kawasaki Ninja 250 Posts: 124
|
I got the tank off!!! I i have a 3/16 and this smaller one but it's not saying what size it is. It feels like it fits down in there but it's not pulling the plug
__________________________________________________
Present: 05 Kawasaki Ninja 250 Past: 02 Honda Rebel, 09 CFMoto Glory 150 |
|
July 13th, 2014, 05:54 AM | #5 |
Que Buenos Son!!!
Name: Ryan
Location: Grovetucky, OH
Join Date: Jun 2012 Motorcycle(s): Aprilia Shiver 750, Husaberg FE 450, Ninja 300 (sold), xr100 Posts: A lot.
MOTM - Nov '14
|
Is the plug loose? If it is then I've always used a magnetic pick up tool to get them out. Like this
If they aren't loose then it sounds like you need a different size socket.
__________________________________________________
Don't do something because it's easy,.. Do it because it's not! If you aren't going forward, then you're falling behind. "Drive it like you stole it"!!! |
|
July 13th, 2014, 06:17 AM | #6 |
ninjette.org member
Name: Amy
Location: Northeast Ohio
Join Date: Jul 2014 Motorcycle(s): 2005 Kawasaki Ninja 250 Posts: 124
|
Looks like 5/8 is the right size socket so I'm gonna go grab that at the store and should be able to get to the plugs then
__________________________________________________
Present: 05 Kawasaki Ninja 250 Past: 02 Honda Rebel, 09 CFMoto Glory 150 |
|
July 13th, 2014, 08:58 AM | #7 |
ninjette.org member
Name: Amy
Location: Northeast Ohio
Join Date: Jul 2014 Motorcycle(s): 2005 Kawasaki Ninja 250 Posts: 124
|
Attached pics of the plugs after I went out and got the 5/8 socket. They look ok so I put them back in and everything back together. Only bad thing..I over toughened the one of the two tank screws that hold it onto the frame and it broke off in the hole. So it's fastened on tight by the one main screw and of course the fairings and the fuel lines are all good. Took it for a 15 min or so riel and it rode well.
__________________________________________________
Present: 05 Kawasaki Ninja 250 Past: 02 Honda Rebel, 09 CFMoto Glory 150 |
|
July 13th, 2014, 09:08 AM | #8 |
RIP Alex
Name: Cuong
Location: Houston, TX
Join Date: Apr 2011 Motorcycle(s): '10 250r, '09 265r Posts: A lot.
Blog Entries: 2
|
Hard to see but from what I can tell it looks ok.
__________________________________________________
HalfFast Racing Team Serving Greater Houston Area Riders:WFO Riders MotoHouston HPC CMRA Ride Smart Fastline Lone Star Track Days |
|
July 14th, 2014, 01:22 PM | #9 |
ninjette.org sage
Name: bob
Location: Earf
Join Date: Apr 2013 Motorcycle(s): 2005 Ninja 250, 2006 SV650N Posts: 642
|
Just make sure you stick with NGK if you replace them. That bolt size is 6x25 for the gas tank. It will be cheaper if you can find it in a local store but here it is on bikebandit. I actually need a lower fairing bolt but have it zip tied since I couldn't find a good replacement at lowes. Anyone know of a good spot to pick up fairing bolts for cheap?
http://www.bikebandit.com/2005-kawas...9183#sch433967 |
|
July 14th, 2014, 01:24 PM | #10 |
ninjette.org member
Name: Amy
Location: Northeast Ohio
Join Date: Jul 2014 Motorcycle(s): 2005 Kawasaki Ninja 250 Posts: 124
|
Regarding my broken tank bolt
For now I've just let it be and securely fastened the other tank bolt and the fairing bolts. How would I get that broken bolt piece out to put a new bolt piece in? If I just start screwing in the new bolt could I risk damaging it as it hits into the broken piece?
__________________________________________________
Present: 05 Kawasaki Ninja 250 Past: 02 Honda Rebel, 09 CFMoto Glory 150 |
|
July 14th, 2014, 01:56 PM | #11 |
Que Buenos Son!!!
Name: Ryan
Location: Grovetucky, OH
Join Date: Jun 2012 Motorcycle(s): Aprilia Shiver 750, Husaberg FE 450, Ninja 300 (sold), xr100 Posts: A lot.
MOTM - Nov '14
|
Yeah, you will need to get that bolt out. If I remember correctly that bolt just screws into a bracket. You'll have to at least partially remove the tank again to get to the bracket, but it should be easy to get the broken bolt out once you do.
__________________________________________________
Don't do something because it's easy,.. Do it because it's not! If you aren't going forward, then you're falling behind. "Drive it like you stole it"!!! |
|
July 14th, 2014, 05:36 PM | #12 | |
Threadkiller
Name: Mick
Location: Monongahela, Pa.
Join Date: Apr 2014 Motorcycle(s): Yellow '04 stocker, '89 FJ1200, '87 Ducati Paso, '71 Yamaha XS1b, '99 KLR650, '81 FXE 80, '97 KTM 200EXC , etc Posts: 430
|
Quote:
You'll probably have to drill it out. Centerpunch as close to center as you can, then start the hole with a small bit and work your way up. Then retap with a 6mm. |
|
|
July 14th, 2014, 06:13 PM | #13 |
Inline 4!!!
Name: Danny
Location: MA
Join Date: May 2014 Motorcycle(s): 2008 CBR600rr, 1987 KLR 250 Posts: A lot.
|
When I had my pregen, I was removing my gas tank on a daily basis working on my damn carbs ...
__________________________________________________
Be careful. Remember you are invisible |
|
July 14th, 2014, 06:44 PM | #14 |
Participant
Name: Dave
Location: South of Seattle
Join Date: Oct 2012 Motorcycle(s): '94 K75 std Posts: Too much.
MOTM - Aug '15
|
|
|
July 17th, 2014, 04:37 AM | #15 | |
Captain 2 Sexy
Name: Newton
Location: South TN
Join Date: Apr 2014 Motorcycle(s): Kwaka EX250 Posts: 241
|
Quote:
Your local hardware store with a decent bolt bin would have these and they are cheap so you could buy more than one. Learn to feel what snug is, or invest in a small torque wrench. |
|
|
July 18th, 2014, 01:07 AM | #16 |
Phoenix Salvage
Name: Mac
Location: AR
Join Date: May 2014 Motorcycle(s): 2007 Ninja 250R Posts: 71
|
When I got mine, the left tank bracket bolt was sheared off as well, while the other snapped as I was attempting to loosen it. I've just resigned myself to the fact that while I love my bike, kawasaki uses some of the worst fasteners on earth for the 250.
I unbolted the bracket from the frame and managed to work out the broken half with some pliers and a bit of wd40 in an effort to avoid drilling it. If it has any sticking out of the bottom of the bolt hole, it may be worth a shot. If you haven't replaced it in a few weeks, let me know, and I'll likely have a few replacement bolt kits in stock. I don't think there was a single bolt on my bike that wasn't stripped to the point of uselessness, or rusted to the point of crumbling, so I finally snapped myself and replaced the tank bracket and fuel filler cap with forged titanium bolts for their anti-corrosion properties. Horrible investment yes, but almost two years later they still look brand new despite being constantly exposed to the elements and being taken on and off a hundred times. In retrospect, stainless would've done the same thing, but I wanted to do something nice for her.
__________________________________________________
See my current inventory of used parts for sale here |
|
July 18th, 2014, 06:42 AM | #17 |
Participant
Name: Dave
Location: South of Seattle
Join Date: Oct 2012 Motorcycle(s): '94 K75 std Posts: Too much.
MOTM - Aug '15
|
Another strategy is to get regular steel fasteners and put a light coating of anti-seize compound (or even grease) on the fastener thread prior to insallation (or reinstallation). Only needs to be done one time.
|
|
July 18th, 2014, 09:23 AM | #18 | |
ninjette.org sage
Name: bob
Location: Earf
Join Date: Apr 2013 Motorcycle(s): 2005 Ninja 250, 2006 SV650N Posts: 642
|
Quote:
|
|
|
July 20th, 2014, 02:33 AM | #19 |
Captain 2 Sexy
Name: Newton
Location: South TN
Join Date: Apr 2014 Motorcycle(s): Kwaka EX250 Posts: 241
|
They use the same hardware many other companies use, and I use, with no problems. This was a problem caused by the previous owner.
|
|
July 27th, 2014, 04:04 AM | #20 |
Wannabe Reborn
Name: Unregistered
Location: Cincy Ohio
Join Date: Mar 2009 Motorcycle(s): Blue 2008 Ninja 250 Posts: 302
|
To get the broken bolt out, before you start drilling it out, try and turn it out with a small screwdriver, slotted of course. Sometimes with a broken bolt you get lucky and can un thread it out easily. If its cross threaded, then thats a whole other ball game...
__________________________________________________
" If you're here to show off and prove that your crotch rocket is faster than my Harley, you can leave now. " |
|
August 2nd, 2014, 05:36 AM | #21 |
ninjette.org member
Name: Aaron
Location: Knoxville
Join Date: Jul 2014 Motorcycle(s): 2006 Honda ST1300, 2001 Ninja 250 Posts: 53
|
As long as you had the plugs out, why didn't you just put new ones in? I did this a few days ago, and the NGK plugs were only a couple bucks each.
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
disc lock, 08-12 spark plug boot, shim kit, DID chain breaker/rivet tool | CThunder-blue | Motorcycle-related | 15 | March 10th, 2015 09:59 AM |
Spark plugs? | corksil | 2008 - 2012 Ninja 250R Tech Talk | 12 | October 1st, 2013 11:04 AM |
Removing spark spark plugs? | tsdexter | 2008 - 2012 Ninja 250R Tech Talk | 3 | June 26th, 2013 03:48 PM |
spark plug tool | rideclassiv | 1986 - 2007 Ninja 250R Tech Talk | 11 | March 19th, 2012 10:49 AM |
What spark plugs... | cbowman78 | 2008 - 2012 Ninja 250R Tech Talk | 5 | December 8th, 2010 06:36 AM |
|
|