Track build

ROB654 · May 29th, 2017, 06:37 PM

I started working on my track build again. I got most of the parts in for the build. It's a 2008 Ninja 250. I'm setting it up for track days and racing. I haven't raced in many years. I've been really missing being on the track.

I'll take any input or helpful thoughts with this build

ROB654 · May 29th, 2017, 06:46 PM

Here's what I got done so far. I put in a set of tapered steering bearings, Factory shift detent and remove a lot of weight saving non needed stuff

csmith12 · May 29th, 2017, 07:06 PM

DannoXYZ · May 30th, 2017, 04:39 AM

Here's what I've done to mine.

- Woodcraft clip-ons
- Woodcraft rearsets
- TrailTech Vapor gauges
- Hotbodies bodywork
- Galfer SS brake lines
- Galfer disks
- Shaved kickstand bracket (no highsides allowed)
- Tyga full stainless exhaust system
- Motionpro Rev2 throttle set
- 428 chain and aluminum rear sprocket (sprocketspecialists.com)
- K-Tech rear suspension
- Progressive front springs with gold cartridge emulators
- Barnett clutch and springs
- Fully safety wired
- TechEdge wideband for tuning
- DynoJet tuning kit

I need to review the rulebook, but I believe I'm allowed to increase compression. So in off-season I'll rebuild engine and put in some 12,5:1 pistons.

ROB654 · May 30th, 2017, 04:47 PM

Latest additions to build
Aluminum fairing bracket
Blue aluminum oil fill cap
Woodcraft ignition elimination harness

dustinang87 · May 31st, 2017, 04:27 PM

where did you pickup that fairing bracket from?

ROB654 · May 31st, 2017, 05:00 PM

I what to say eBay a few years ago. But let me see if I can find any paper work on it

ROB654 · June 2nd, 2017, 02:36 PM

How much should I drop the triple clamps. What should the measurement be from the top triple clamp to the top of the fork tube?

Dave Wolfe · June 2nd, 2017, 04:56 PM

About 12mm for stock. Salt to taste once you get on the track.

DannoXYZ · June 5th, 2017, 10:22 AM

I have 15mm drop on mine with the pre-load adjusters 2 full-turns in. I weigh 82 kg.

May 29th, 2017, 07:06 PM	#3
csmith12 The Corner Whisperer Name: Chris (aka Reactor) Location: Northern KY Join Date: May 2011 Motorcycle(s): 2010 250 (track), 1992 250, 2006 R6 (street/track), 2008 R6 (track) Posts: Too much. MOTY 2015, MOTM - Nov '12, Nov '13	__________________________________________________ Goal: Shake A Million Hands \| Look through the corners \| Track Day Prep \| Closest track? \| The Mid-Ohio School

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Howlinhoss's Track Build	howlinhoss	Ninjettes At Speed	38	August 18th, 2015 06:34 AM
2010 Track Build	Floki	2008 - 2012 Ninja 250R Tech Talk	57	June 24th, 2015 12:34 PM
08 Ninja 250 track build	ROB654	2008 - 2012 Ninja 250R Farkles	10	May 14th, 2015 08:32 PM
08 r6 Track/Race Build	csmith12	Pictures	48	May 3rd, 2015 08:34 PM
Need help with Track build	jmk420	Ninjettes At Speed	35	June 24th, 2014 05:59 PM

May 30th, 2017, 04:39 AM	#4
DannoXYZ ninjette.org certified postwhore Name: AKA JacRyann Location: Mesa, AZ Join Date: Dec 2011 Motorcycle(s): CB125T CBR250R-MC19 CBR250RR-MC22 NSR350R-MC21 VF500F CBR600RR SFV650 VFR750F R1M ST1300PA Valkyrie-F6C Posts: A lot. MOTY - 2018, MOTM - Nov '17	Here's what I've done to mine. - Woodcraft clip-ons - Woodcraft rearsets - TrailTech Vapor gauges - Hotbodies bodywork - Galfer SS brake lines - Galfer disks - Shaved kickstand bracket (no highsides allowed) - Tyga full stainless exhaust system - Motionpro Rev2 throttle set - 428 chain and aluminum rear sprocket (sprocketspecialists.com) - K-Tech rear suspension - Progressive front springs with gold cartridge emulators - Barnett clutch and springs - Fully safety wired - TechEdge wideband for tuning - DynoJet tuning kit I need to review the rulebook, but I believe I'm allowed to increase compression. So in off-season I'll rebuild engine and put in some 12,5:1 pistons.

May 31st, 2017, 04:27 PM	#6
dustinang87 ninjette.org newbie Name: Dustin Location: San Mateo, CA Join Date: Nov 2016 Motorcycle(s): Ninja 250r, Ducati 1098, Honda Grom Posts: 6	where did you pickup that fairing bracket from?

May 31st, 2017, 05:00 PM	#7
ROB654 ninjette.org member Name: ROB Location: WORCESTER Join Date: Oct 2014 Motorcycle(s): 08 NINJA 250,EX500,YSR50,86 VFR750 Posts: 54	I what to say eBay a few years ago. But let me see if I can find any paper work on it

June 2nd, 2017, 02:36 PM	#8
ROB654 ninjette.org member Name: ROB Location: WORCESTER Join Date: Oct 2014 Motorcycle(s): 08 NINJA 250,EX500,YSR50,86 VFR750 Posts: 54	How much should I drop the triple clamps. What should the measurement be from the top triple clamp to the top of the fork tube?

June 2nd, 2017, 04:56 PM	#9
Dave Wolfe CCS Amateur #501 Name: Dave Location: Iowa Join Date: Jun 2015 Motorcycle(s): '09 250 SE 'Booger' Posts: 406	About 12mm for stock. Salt to taste once you get on the track.

June 5th, 2017, 10:22 AM	#10
DannoXYZ ninjette.org certified postwhore Name: AKA JacRyann Location: Mesa, AZ Join Date: Dec 2011 Motorcycle(s): CB125T CBR250R-MC19 CBR250RR-MC22 NSR350R-MC21 VF500F CBR600RR SFV650 VFR750F R1M ST1300PA Valkyrie-F6C Posts: A lot. MOTY - 2018, MOTM - Nov '17	I have 15mm drop on mine with the pre-load adjusters 2 full-turns in. I weigh 82 kg.