![]() |
![]() |
#1 |
ninjette.org guru
Name: Joel
Location: Sandy Eggo north
Join Date: Aug 2012 Motorcycle(s): '13 Ninja 300, '99 SV650 tracked Posts: 378
|
Clutch Adjustment
So my clutch engages ridiculously high, like almost all the way out, is spinning the nut next to the lever the only way to control the travel before engagement? (Didn't seem to effect it at all) I'm an idiot with a wrench, so feel free to overstate the obvious. Thanx,
Joel |
![]() |
![]() |
![]() |
#2 |
wat
Name: wat
Location: tustin/long beach
Join Date: Sep 2009 Motorcycle(s): wat Posts: Too much.
Blog Entries: 5
MOTM - Oct '12, Feb '14
|
haven't had a chance to look at the 300 yet, but there should be the standard adjuster at the handle bar lever, as well as another adjuster at the clutch pull mechanism on the right side of the engine where the cable attaches to the clutch pull lever on the engine... should be two 10mm nuts on either side of the holder plate, loosen the bottom nut, then you can pull it out a bit so you can move the top nut to adjust it, then tighten the bottom nut back down.
__________________________________________________
![]() ![]() ![]() |
![]() |
![]() |
![]() |
#3 |
ninjette.org guru
Name: Joel
Location: Sandy Eggo north
Join Date: Aug 2012 Motorcycle(s): '13 Ninja 300, '99 SV650 tracked Posts: 378
|
Thanx Alex, I'll give it a try tonight.
![]() |
![]() |
![]() |
![]() |
#4 |
ninjette.org member
Name: Kawi girl
Location: California
Join Date: Oct 2012 Motorcycle(s): 2013 ninja 300 Posts: 38
|
![]()
And remember this bike has a slipper clutch. It has a short friction zone, basically built with racing in mind (one or two finger shift style). I can literally shift with my thumb and index finger and I'm a girl... heeeheeheee!!!! Clutch engagement is almost at full release to allow this type of shifting. However, you can adjust it slightly to engage sooner by spinning (clockwise will allow for engagement sooner; counter clockwise engagement later) the adjuster at the end of the clutch lever. I wouldn't recommend changing the position of the cable located on the clutch arm.
|
![]() |
![]() |
![]() |
#5 |
wat
Name: wat
Location: tustin/long beach
Join Date: Sep 2009 Motorcycle(s): wat Posts: Too much.
Blog Entries: 5
MOTM - Oct '12, Feb '14
|
There shouldn't be much play. If you want to adjust the default position if the levers you want adjustable levers. Not sure but I don't think the 300 levers are adjustable. Check out pazzo levers or cheap ebay knockoffs that fade like "the2wheels" (popular seller)
__________________________________________________
![]() ![]() ![]() |
![]() |
![]() |
![]() |
#6 |
ninjette.org member
Name: J
Location: Toronto
Join Date: Sep 2012 Motorcycle(s): Ninja 300 Posts: 103
|
Heh, they won't fade if you just get it in silver
__________________________________________________
My Ninja 300 Build Photoblog Greater Toronto Area 250/300 Riding Group |
![]() |
![]() |
![]() |
#7 |
ninjette.org newbie
Name: Jasper
Location: portland OR
Join Date: Oct 2012 Motorcycle(s): Ninja 300 green/blk ABS Posts: 7
|
I'm having the same issue. my hand barely extends far enough to use the friction zone. im doing almost all my clutch handling with the tips of my fingers and its extremely difficult to do anything accurately. about half of my starts have been jumping off the line instead of smooth.
has anyone changed the clutch levers yet? do the old 250r ones work or do i need to wait for companies to eventually come out with some for the 300? |
![]() |
![]() |
![]() |
#8 |
CPT Falcon
Name: J.Emmett Turner
Location: Newnan, GA
Join Date: Apr 2009 Motorcycle(s): '08 CP Blue EX250J, '97 unpainted EX250F, 2nd '97 unpainted EX250F (no engine), '07 black EX250F Posts: A lot.
|
My entire friction zone is also in the last tiny bit of lever travel as I release it.
|
![]() |
![]() |
![]() |
#9 | |
Long Time Rider
Name: Blue
Location: Charlotte, NC
Join Date: Sep 2010 Motorcycle(s): 2009 Kawasaki Ninja 250R Posts: A lot.
|
Quote:
|
|
![]() |
![]() |
![]() |
#10 |
Finding some curves....
Name: Thomas
Location: Hurst,Texas
Join Date: Sep 2012 Motorcycle(s): 2013 300 Ninja Posts: 268
|
I agree adjustable levers are a great solution. Thats what i did.
|
![]() |
![]() |
![]() |
#11 |
ninjette.org member
Name: Norman
Location: Eugene, Oregon
Join Date: Apr 2011 Motorcycle(s): BMW K12RS, DL650 , New 2013 "WonderBike" Ninja300SE Posts: 52
|
|
![]() |
![]() |
![]() |
#12 |
ninjette.org member
Name: Carlos
Location: Puerto Rico
Join Date: Jan 2013 Motorcycle(s): Ninja 300R Posts: 181
|
imo, i like it that it engages at almost at full release, i can do fast shifting with 2 fingers, awesome imo, i put some shorty levers on my 300, loving it so far
|
![]() |
![]() |
![]() |
#13 |
ninjette.org newbie
Name: Christopher
Location: Indiana
Join Date: Feb 2017 Motorcycle(s): 2007 Kawasaki Ninja 650R Posts: 9
|
Hello. I saw this post and figured I would plead for help. I just installed Pazzo Ebay replica shorts on both. Now my clutch is not working. I can go into first without clutching. When I squeeze lever bike is very difficult to free wheel. Works great in neutral. I cannot go up from there. I am new to working on a mc, but wanot to learn and do what I can myself. With being destitute and penniless, it helps.
Would anyone please be so kind to give me some advice? I was told to play with adjuster by lever, no good. Someone else said that I need to adjust cable on right as well, due to short levers not having the full stroke as the stock. ??? |
![]() |
![]() |
![]() |
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Lighting, clutch adjustment and more | yogurtpooh | 2008 - 2012 Ninja 250R Tech Talk | 13 | December 3rd, 2014 07:09 PM |
Clutch Adjustment? | Archerzz | 1986 - 2007 Ninja 250R Tech Talk | 5 | July 15th, 2011 02:33 PM |
Clutch adjustment bolts | peter330 | 2008 - 2012 Ninja 250R Tech Talk | 2 | June 1st, 2010 03:59 PM |
Valve Adjustment-Really Tight adjustment screw? | mikesova | 1986 - 2007 Ninja 250R Tech Talk | 5 | May 2nd, 2010 04:57 AM |
Clutch cable adjustment | SteveL | 2008 - 2012 Ninja 250R Tech Talk | 2 | August 17th, 2009 12:39 AM |
|
|