Keyless ignition

Kevinnolde · August 31st, 2009, 04:20 PM

One of my rental bikes has damaged an ignition unit making me think about doing keyless ignitions to the fleet and saving a lb. per unit. Anyone tried it? and can provide the wires to connect. It appears that if I connect the brown, the white and the grey at the key plug (harness side) and then connect that group to the red in the on off switch it should be ok. Another thing is why does the grey wire at the key plug read 11 volts instead of 13.8 like the rest of the hot wires at the plug. I know it goes to the ecu but then what? Be kind. Kevin

Kevinnolde · August 31st, 2009, 06:22 PM

So I have connected the brown with the white and it will run, it will not run if the grey is not hooked up through the key. According to the diagram I could connect the white grey and brown and it should run, it does not. Kevin

Kevinnolde · September 1st, 2009, 05:30 AM

The bikes all have the clutch and side safeties disabled and the bike was in neutral. The grey wire shoed 11 volts while running.

Kevinnolde · September 1st, 2009, 08:31 AM

I'll fool with it in a minute, I can't remember all of the varients that I tried, I'll go write them down.

August 31st, 2009, 04:20 PM	#1
Kevinnolde www.rentmyninja.com Name: Kevin Location: Louisiana Join Date: Jun 2009 Motorcycle(s): A six Pack of Ninja 250s, a less frequently used ZX10r and a few Mini dirt bikes Posts: 23	Keyless ignition One of my rental bikes has damaged an ignition unit making me think about doing keyless ignitions to the fleet and saving a lb. per unit. Anyone tried it? and can provide the wires to connect. It appears that if I connect the brown, the white and the grey at the key plug (harness side) and then connect that group to the red in the on off switch it should be ok. Another thing is why does the grey wire at the key plug read 11 volts instead of 13.8 like the rest of the hot wires at the plug. I know it goes to the ecu but then what? Be kind. Kevin

August 31st, 2009, 06:22 PM	#2
Kevinnolde www.rentmyninja.com Name: Kevin Location: Louisiana Join Date: Jun 2009 Motorcycle(s): A six Pack of Ninja 250s, a less frequently used ZX10r and a few Mini dirt bikes Posts: 23	wires So I have connected the brown with the white and it will run, it will not run if the grey is not hooked up through the key. According to the diagram I could connect the white grey and brown and it should run, it does not. Kevin

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
09 Keyless Ignition	Chad4434	2008 - 2012 Ninja 250R Tech Talk	15	October 5th, 2016 04:12 AM
ninja 250 keyless ignition	timone1002	Ninjettes At Speed	18	October 4th, 2016 08:00 PM
DIY Keyless Ignition for 08 250	garth285	2008 - 2012 Ninja 250R Tech Talk	9	July 18th, 2014 01:39 PM
Is there a DIY for keyless ignition?	Triple R	2008 - 2012 Ninja 250R Tech Talk	8	June 26th, 2014 02:53 PM
Keyless Gas Cap	LittleRedNinjette	Items Wanted	7	March 15th, 2013 10:34 AM

September 1st, 2009, 05:30 AM	#3
Kevinnolde www.rentmyninja.com Name: Kevin Location: Louisiana Join Date: Jun 2009 Motorcycle(s): A six Pack of Ninja 250s, a less frequently used ZX10r and a few Mini dirt bikes Posts: 23	The bikes all have the clutch and side safeties disabled and the bike was in neutral. The grey wire shoed 11 volts while running.

September 1st, 2009, 08:31 AM	#4
Kevinnolde www.rentmyninja.com Name: Kevin Location: Louisiana Join Date: Jun 2009 Motorcycle(s): A six Pack of Ninja 250s, a less frequently used ZX10r and a few Mini dirt bikes Posts: 23	I'll fool with it in a minute, I can't remember all of the varients that I tried, I'll go write them down.