Bringin' Home the cycle.

gagt04 · February 24th, 2009, 12:41 PM

Hey, I'm going to pick up my ninja this week, but its a lil' cold to ride her home. So, i'm going to put her on a trailer and do it that way. I really dont want to but a wheel chuck because this will prolly be the only time it's on a trailer. For the front wheel to kinda anchor it in, can i just screw some 2x4's on each side of the tire? And then with the tie downs, where is the best place to bring the straps over/or through the bike. and should i tighten them down so that the suspension is all of the way down and doesnt move or what. Thanks for the help!!

Alex · February 24th, 2009, 12:50 PM

You never want to compress a motorcycle's suspension that much when trailering it; otherwise you can blow fork seals and damage rear shocks. At most they should be compressed perhaps 1/3 of their travel. If you don't have a chock, anchoring some 2x4's alongside the front wheel should work fine. This gadget is useful for anchoring the front end:

http://www.cyclecynch.com/

and I then put two straps on the rear from the rear passenger pegs to the trailer. If you aren't fully confident in how to do this yourself, just have the dealership deliver it for you. They likely have more experience toting bikes around safely than the rest of us put together.

CC Cowboy · February 24th, 2009, 12:51 PM

Buy some tie downs (with the extra handlebar straps) at the dealer and have him secure the bike on the trailer. This way he is respossible to do it correctly and you should have no problems. If the front of the bike is secure there is no need for wheel chock or any other devices. I've done thousands of miles with bikes on trailers and have never had a problem with just using two tie downs on the handle bars.

kkim · February 24th, 2009, 12:54 PM

Put the bike straight onto the trailer with the front wheel centered in the trailer. Use tie downs on the handlebar area (careful of the wiring) down to the corners of the trailer. Pull down on the tire downs so the bike will not move. After you've got it secured, put a rubber band, tie wrap or small bungee cord around the front brake lever to engage it and the bike will not move if all done correctly. The engaged front brake lever adds a final degree of stability to the tied down bike.

Congrats on the purchase!!

gagt04 · February 24th, 2009, 12:58 PM

Im buying the bike used for a private seller, so i will just tie her down good i guess.....thanks!!

Alex · February 24th, 2009, 01:04 PM

Ratcheting tie downs are easier to use than the standard type, but if you do get them be careful not to overtighten them.

Beast · February 24th, 2009, 01:31 PM

Thanks for the tips Alex! I never knew that overtightening could damage the suspension. In my mind, shocks compress so a little compression won't hurt? Guess I was way off

Kelly, I will definitely use the rubberband over the front brake lever trick. Such a simple solution!

Here is how I transport my bike to and from the track (I will do it correctly in the future):

OldGuy · February 24th, 2009, 01:48 PM

I know you said you were going to use a trainler and I'm not sure what size or configuration. Apply this solution as needed.

When I brought mine home from SD the dealer loaded the bike straight into the back of my pick-up, left it in first gear, and then used a ratchet tie-down on each side of the front to the box. Come up under the fairing, wrap the web around the top of the tube and then loop through the hook. Only snug down enough on each side to be firm, DO NOT FULLY COMPRESSION the front suspension. In the back I just looped a tie down around the rear wheel and tied it to either side of the box.

I'll take some pictures when I get home.

CAUTION - when you go to off load the bike be very careful when releasing the tension on the front straps. Best way is for you or someone to be siting on the bike so it doesn't get pulled to the other side. If you are going to do it by yourself, put a 2x4 under the kick stand and SLOWLY release the tension on the right side first.

Sailariel · February 24th, 2009, 02:01 PM

Chris, That Pearl paint job and Gold wheels is stunning. I plan on going the Gold wheel route.

HKr1 · February 24th, 2009, 02:22 PM

Canyon Dancers FTW!

Hey Chris, where did you find that little trailer?

xTKx · February 24th, 2009, 02:38 PM

Quote:

Originally Posted by gagt04

Im buying the bike used for a private seller, so i will just tie her down good i guess.....thanks!!

Congrats on the bike Matt! Hopefully I'll be purchasing mine soon as well!

BlueTyke · February 24th, 2009, 03:36 PM

Congrats on the buy!

As for the wheel chuck my s/o keeps his bike in it all the time. Of course he has a big boy bike

For trailering we use canyon dancers as well as the straps. my s/o normally does the loading but I do know now (grr) not to let the straps cross across the bike. On our journey from CA to MD he (grr) passed straps that held his bike in place across Tyke's front fender and it rubbed the paint then of course now she's got a bald patch...

Beast · February 24th, 2009, 05:15 PM

Quote:

Originally Posted by Sailariel

Chris, That Pearl paint job and Gold wheels is stunning. I plan on going the Gold wheel route.

Woot!

Just make sure your shop does it right

Quote:

Hey Chris, where did you find that little trailer?

Not so little (the price that is) hahah. I bought the dual rail setup so I could potentially haul my Ninja AND my Vespa in the event I have to move, vacations, etc. I also have two (optional) wheel chocks.

This trailer literally is a trailer in a bag. You can break it down in minutes and rebuild it in minutes. Industrial strength cotter pins attach everything.

http://www.trailerinabag.com

Alex · February 24th, 2009, 06:26 PM

Quote:

Originally Posted by HKr1

Canyon Dancers FTW!

Check out that cycle cynch. Basically, improved Canyon Dancers that aren't as hard on the grips. I used a set of Dancers for years, and the Cycle Cynch does do a better job.

OldGuy · February 24th, 2009, 06:51 PM

Mean while back at the thread of the OP

Working from the top is the easiest. You want the wrap to be above the clamps.

Lock it down in the hook

Unless you are tying off real high you shouldn't have any web rubbing on the fairing.

noche_caliente · February 24th, 2009, 07:16 PM

brought mine home through some twisties just fine secured like this:

Had the dealer secure her for me....

kkim · February 24th, 2009, 08:11 PM

So, Matt... did you get a good deal on your bike?

gagt04 · February 24th, 2009, 09:09 PM

I think so... it has 3,000 miles on it, never been dropped, and has a two brothers al. slip on. Also it got a dyno jet kit. Red is the color and it came with a joe rocket ballistics jacket and an alright helmet, cant remember the name, not that good. the final price was $3,000. not to bad in my mind. compared to what i see on ebay, 4 grand for a stock 08? thats a lil much for me.

OldGuy · February 24th, 2009, 09:13 PM

It will be fun to hear your impressions of the little monster when you get it home. Keep us posted.

kkim · February 24th, 2009, 09:15 PM

Matt... PO anyone on the boards?

gagt04 · February 24th, 2009, 09:24 PM

PO??? I'm new to this forum stuff...lol...what does that mean?

kkim · February 24th, 2009, 09:48 PM

sorry... previous owner.

gagt04 · February 24th, 2009, 09:56 PM

lol...thats alright... nope i found it through craigs list.

gagt04 · February 28th, 2009, 10:22 PM

haha...so it turns out that when i called the guy back, he had just sold it for the same price. I was going up that day to pick it up and pay him, lets just say i was not happy. Anyways, does anyone know about the 2004 suzuki gs500f's. The one im looking at is $2500 with 1300 miles on it. any info would be greatly appreciated.

OldGuy · February 28th, 2009, 10:55 PM

Sorry about the news Matt - that really bites the bag. Keep looking, your Ninja is out there waiting for you to find it.

February 24th, 2009, 12:41 PM	#1
gagt04 ninjette.org member Name: Matt Location: Alma Center Wisconsin Join Date: Feb 2009 Motorcycle(s): Soon To Be A Red 08 Ninja 250 Posts: 18	Bringin' Home the cycle. Hey, I'm going to pick up my ninja this week, but its a lil' cold to ride her home. So, i'm going to put her on a trailer and do it that way. I really dont want to but a wheel chuck because this will prolly be the only time it's on a trailer. For the front wheel to kinda anchor it in, can i just screw some 2x4's on each side of the tire? And then with the tie downs, where is the best place to bring the straps over/or through the bike. and should i tighten them down so that the suspension is all of the way down and doesnt move or what. Thanks for the help!!

February 24th, 2009, 12:50 PM	#2
Alex ninjette.org dude Name: 1 guess :-) Location: SF Bay Area Join Date: Jun 2008 Motorcycle(s): '13 Ninja 300 (white, the fastest color!), '13 R1200RT, '14 CRF250L, '12 TT-R125LE Posts: Too much. Blog Entries: 7	You never want to compress a motorcycle's suspension that much when trailering it; otherwise you can blow fork seals and damage rear shocks. At most they should be compressed perhaps 1/3 of their travel. If you don't have a chock, anchoring some 2x4's alongside the front wheel should work fine. This gadget is useful for anchoring the front end: http://www.cyclecynch.com/ and I then put two straps on the rear from the rear passenger pegs to the trailer. If you aren't fully confident in how to do this yourself, just have the dealership deliver it for you. They likely have more experience toting bikes around safely than the rest of us put together. __________________________________________________ Montgomery Street Motorcycle Club / cal24.com / crf250l.org / ninjette.org ninjette.org Terms of Service Shopping for motorcycle parts or equipment? Come here first. The friendliest Ninja 250R/300/400 forum on the internet! (especially Unregistered)

February 24th, 2009, 01:04 PM	#6
Alex ninjette.org dude Name: 1 guess :-) Location: SF Bay Area Join Date: Jun 2008 Motorcycle(s): '13 Ninja 300 (white, the fastest color!), '13 R1200RT, '14 CRF250L, '12 TT-R125LE Posts: Too much. Blog Entries: 7	Ratcheting tie downs are easier to use than the standard type, but if you do get them be careful not to overtighten them. __________________________________________________ Montgomery Street Motorcycle Club / cal24.com / crf250l.org / ninjette.org ninjette.org Terms of Service Shopping for motorcycle parts or equipment? Come here first. The friendliest Ninja 250R/300/400 forum on the internet! (especially Unregistered)

February 24th, 2009, 01:31 PM	#7
Beast Pure Imagination Name: Chris Location: Burbank, CA Join Date: Dec 2008 Motorcycle(s): 08' 250r, '07 Vespa LX150 (it counts right?) Posts: 183	Thanks for the tips Alex! I never knew that overtightening could damage the suspension. In my mind, shocks compress so a little compression won't hurt? Guess I was way off Kelly, I will definitely use the rubberband over the front brake lever trick. Such a simple solution! Here is how I transport my bike to and from the track (I will do it correctly in the future): __________________________________________________ Yoshi CF Slip on, Galfer SS lines, Motul 5.1, HH brake pads, Dynojet Jet Kit, BT-090's, Pearl white paint + flat black accent, Gold wheels, A-Tech CF front fender, A-Tech tank pad, BEET rearsets

February 24th, 2009, 01:48 PM	#8
OldGuy Live Life Name: Don Location: Lincoln, NE Join Date: Nov 2008 Motorcycle(s): 2009 Green SE Ninja 250 Posts: A lot.	I know you said you were going to use a trainler and I'm not sure what size or configuration. Apply this solution as needed. When I brought mine home from SD the dealer loaded the bike straight into the back of my pick-up, left it in first gear, and then used a ratchet tie-down on each side of the front to the box. Come up under the fairing, wrap the web around the top of the tube and then loop through the hook. Only snug down enough on each side to be firm, DO NOT FULLY COMPRESSION the front suspension. In the back I just looped a tie down around the rear wheel and tied it to either side of the box. I'll take some pictures when I get home. CAUTION - when you go to off load the bike be very careful when releasing the tension on the front straps. Best way is for you or someone to be siting on the bike so it doesn't get pulled to the other side. If you are going to do it by yourself, put a 2x4 under the kick stand and SLOWLY release the tension on the right side first. __________________________________________________ - ATGATT - Scorpion EX700 Hi-Vis Helmet, First Gear MeshTek 3.0 Jacket, TourMaster Transition 2 Jacket and Flex Pants, Sidi Doha boots

February 24th, 2009, 12:51 PM	#3
CC Cowboy ninjette.org certified postwhore Name: Whodat Location: Ware Is.,MA Join Date: Jan 2009 Motorcycle(s): I pass the wind! Posts: A lot. MOTM - Mar '13, Jun '14	Buy some tie downs (with the extra handlebar straps) at the dealer and have him secure the bike on the trailer. This way he is respossible to do it correctly and you should have no problems. If the front of the bike is secure there is no need for wheel chock or any other devices. I've done thousands of miles with bikes on trailers and have never had a problem with just using two tie downs on the handle bars.

February 24th, 2009, 12:54 PM	#4
kkim Join Date: Nov 2008 Posts: Too much.	Put the bike straight onto the trailer with the front wheel centered in the trailer. Use tie downs on the handlebar area (careful of the wiring) down to the corners of the trailer. Pull down on the tire downs so the bike will not move. After you've got it secured, put a rubber band, tie wrap or small bungee cord around the front brake lever to engage it and the bike will not move if all done correctly. The engaged front brake lever adds a final degree of stability to the tied down bike. Congrats on the purchase!!

February 24th, 2009, 12:58 PM	#5
gagt04 ninjette.org member Name: Matt Location: Alma Center Wisconsin Join Date: Feb 2009 Motorcycle(s): Soon To Be A Red 08 Ninja 250 Posts: 18	Im buying the bike used for a private seller, so i will just tie her down good i guess.....thanks!!

February 24th, 2009, 02:01 PM	#9
Sailariel ninjette.org certified postwhore Name: Alex Location: Belfast, ME Join Date: Jul 2008 Motorcycle(s): 2010 Honda NT-700-V, formerly, Green 2008 Ninja 250R Posts: A lot.	Chris, That Pearl paint job and Gold wheels is stunning. I plan on going the Gold wheel route.

February 24th, 2009, 02:22 PM	#10
HKr1 IC2(SW) Name: Kerry Location: Pensacola Join Date: Nov 2008 Motorcycle(s): . Posts: A lot.	Canyon Dancers FTW! Hey Chris, where did you find that little trailer?

February 24th, 2009, 03:36 PM	#12
BlueTyke So slow I'm first! Name: Sunny Location: San Jose, CA Join Date: Oct 2008 Motorcycle(s): 06 Kawasaki Ninja EX250 Posts: A lot. Blog Entries: 10	Congrats on the buy! As for the wheel chuck my s/o keeps his bike in it all the time. Of course he has a big boy bike For trailering we use canyon dancers as well as the straps. my s/o normally does the loading but I do know now (grr) not to let the straps cross across the bike. On our journey from CA to MD he (grr) passed straps that held his bike in place across Tyke's front fender and it rubbed the paint then of course now she's got a bald patch... __________________________________________________ Learn from the mistakes of others, you cannot make them all yourself. Save yourself the trouble and Learn.

February 24th, 2009, 06:51 PM	#15
OldGuy Live Life Name: Don Location: Lincoln, NE Join Date: Nov 2008 Motorcycle(s): 2009 Green SE Ninja 250 Posts: A lot.	Mean while back at the thread of the OP Working from the top is the easiest. You want the wrap to be above the clamps. Lock it down in the hook Unless you are tying off real high you shouldn't have any web rubbing on the fairing. __________________________________________________ - ATGATT - Scorpion EX700 Hi-Vis Helmet, First Gear MeshTek 3.0 Jacket, TourMaster Transition 2 Jacket and Flex Pants, Sidi Doha boots

February 24th, 2009, 07:16 PM	#16
noche_caliente ninjette.org certified postwhore Name: Kim Location: mundo de ensueño Join Date: Nov 2008 Motorcycle(s): '08 250 Posts: A lot.	brought mine home through some twisties just fine secured like this: Had the dealer secure her for me....

February 24th, 2009, 08:11 PM	#17
kkim Join Date: Nov 2008 Posts: Too much.	So, Matt... did you get a good deal on your bike?

February 24th, 2009, 09:09 PM	#18
gagt04 ninjette.org member Name: Matt Location: Alma Center Wisconsin Join Date: Feb 2009 Motorcycle(s): Soon To Be A Red 08 Ninja 250 Posts: 18	I think so... it has 3,000 miles on it, never been dropped, and has a two brothers al. slip on. Also it got a dyno jet kit. Red is the color and it came with a joe rocket ballistics jacket and an alright helmet, cant remember the name, not that good. the final price was $3,000. not to bad in my mind. compared to what i see on ebay, 4 grand for a stock 08? thats a lil much for me.

February 24th, 2009, 09:13 PM	#19
OldGuy Live Life Name: Don Location: Lincoln, NE Join Date: Nov 2008 Motorcycle(s): 2009 Green SE Ninja 250 Posts: A lot.	It will be fun to hear your impressions of the little monster when you get it home. Keep us posted. __________________________________________________ - ATGATT - Scorpion EX700 Hi-Vis Helmet, First Gear MeshTek 3.0 Jacket, TourMaster Transition 2 Jacket and Flex Pants, Sidi Doha boots

February 24th, 2009, 09:15 PM	#20
kkim Join Date: Nov 2008 Posts: Too much.	Matt... PO anyone on the boards?

February 24th, 2009, 09:24 PM	#21
gagt04 ninjette.org member Name: Matt Location: Alma Center Wisconsin Join Date: Feb 2009 Motorcycle(s): Soon To Be A Red 08 Ninja 250 Posts: 18	PO??? I'm new to this forum stuff...lol...what does that mean?

February 24th, 2009, 09:48 PM	#22
kkim Join Date: Nov 2008 Posts: Too much.	sorry... previous owner.

February 24th, 2009, 09:56 PM	#23
gagt04 ninjette.org member Name: Matt Location: Alma Center Wisconsin Join Date: Feb 2009 Motorcycle(s): Soon To Be A Red 08 Ninja 250 Posts: 18	lol...thats alright... nope i found it through craigs list.

February 28th, 2009, 10:22 PM	#24
gagt04 ninjette.org member Name: Matt Location: Alma Center Wisconsin Join Date: Feb 2009 Motorcycle(s): Soon To Be A Red 08 Ninja 250 Posts: 18	haha...so it turns out that when i called the guy back, he had just sold it for the same price. I was going up that day to pick it up and pay him, lets just say i was not happy. Anyways, does anyone know about the 2004 suzuki gs500f's. The one im looking at is $2500 with 1300 miles on it. any info would be greatly appreciated.

February 28th, 2009, 10:55 PM	#25
OldGuy Live Life Name: Don Location: Lincoln, NE Join Date: Nov 2008 Motorcycle(s): 2009 Green SE Ninja 250 Posts: A lot.	Sorry about the news Matt - that really bites the bag. Keep looking, your Ninja is out there waiting for you to find it. __________________________________________________ - ATGATT - Scorpion EX700 Hi-Vis Helmet, First Gear MeshTek 3.0 Jacket, TourMaster Transition 2 Jacket and Flex Pants, Sidi Doha boots

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Ride it home, or trailer it home?	professor gascan	General Motorcycling Discussion	30	March 22nd, 2012 11:30 PM
[nytimes.com] - Marcus Dairy Bar, the Home Away From Home for Motorcyclists, Closes	Ninjette Newsbot	Motorcycling News	0	February 7th, 2011 02:00 PM
[topix.net] - Cycle News Croaks: Jim "the Greek" Gianatsis Says Goodbye to Cycle...	Ninjette Newsbot	Motorcycling News	0	September 3rd, 2010 11:40 PM
[superbikeplanet.com] - Pegram Bringing His Double-Jugs Of Fun Westward (Also bringin	Ninjette Newsbot	Motorcycling News	0	March 20th, 2009 09:00 AM
Frog Cycle	BlueTyke	Off-Topic	7	February 5th, 2009 07:11 AM