August 4th, 2016, 09:38 PM | #1 |
ninjette.org member
Name: Breh
Location: Texas
Join Date: May 2012 Motorcycle(s): 2008 Kawasaki Ninja 250R Posts: 38
|
Chain Adjustment Issue
So earlier today, I checked my chain slack and it was pretty loose. So I put it up on a rear stand, loosened the main bolt in the tire and tightened it up until the slack was about an inch, since I knew the spec calls for between .8 and 1.2.
Got it in spec, used a screwdriver to keep the slack still while I tightened the main bolt back up. So then I ride around some, get back home. Now when I check the slack it's super tight. There's next to no slack in the chain, as if I tightened it too much. Before I went to ride around, the slack was perfect. What happened? |
|
August 4th, 2016, 09:46 PM | #2 |
ninjette.org certified postwhore
Name: Kerry
Location: Ventura, CA
Join Date: Jan 2016 Motorcycle(s): Ninja650 Posts: A lot.
MOTM - Apr '18, Apr '17, Apr '16
|
Some parts of the chain are looser than others. Rotate it around until you identify the tightest spot of the whole thing, and adjust to that.
|
2 out of 2 members found this post helpful. |
August 5th, 2016, 07:07 AM | #3 |
Rev Limiter
Name: Jay
Location: WI
Join Date: Jul 2013 Motorcycle(s): '06 SV650n, '00 Derbi GPR, '64 CA77 Dream 305, '70 CL450 Scrambler, numerous dirt bikes Posts: A lot.
MOTM - Jun '18, Oct '16
|
Watch this video - http://canyonchasers.com/video/howto/chain.php
|
1 out of 1 members found this post helpful. |
August 5th, 2016, 09:51 AM | #4 | |
ninjette.org certified postwhore
Name: Whodat
Location: Ware Is.,MA
Join Date: Jan 2009 Motorcycle(s): I pass the wind! Posts: A lot.
MOTM - Mar '13, Jun '14
|
Quote:
__________________________________________________
If everything seems under control; you're just not going fast enough! |
|
|
August 5th, 2016, 06:07 PM | #5 |
ninjette.org member
Name: Breh
Location: Texas
Join Date: May 2012 Motorcycle(s): 2008 Kawasaki Ninja 250R Posts: 38
|
So I checked the slack again today. The last I rode was yesterday. When I checked the slack now it's sorta okay again, if anything now a little on the loose side, but fine overall. I did spin the wheel to feel the slack change a little, but it seemed way better than yesterday, when it seemed to have no slack after riding a bit. This is a little confusing, what's happening?
|
|
August 5th, 2016, 06:09 PM | #6 |
Vintage Screwball
Name: B
Location: Washington
Join Date: Feb 2016 Motorcycle(s): 2011 Ninja 250, 2008 Ninja 250, 2019 KTM 1290SDR, 2017 FZ10 Posts: A lot.
MOTM - Mar '16
|
Chain warmed up since you rode it? Did you check it right after a ride?
Might have some old lube creating a sticky spot. chain might need a good scrubbing with kerosene and a chain brush.
__________________________________________________
Goin' fast on slow bikes! |
|
August 5th, 2016, 06:33 PM | #7 |
ninjette.org member
Name: Breh
Location: Texas
Join Date: May 2012 Motorcycle(s): 2008 Kawasaki Ninja 250R Posts: 38
|
Yes I checked it right after a ride and it was tight. Just rode it a little more and it seems as the bike warms up the chain gets tighter. Is that normal?
|
|
August 5th, 2016, 07:00 PM | #8 | |
Daily Ninjette rider
Name: Hernan
Location: Florida
Join Date: Mar 2011 Motorcycle(s): 2007 Ninja 250 Posts: A lot.
MOTY - 2016, MOTM - Dec '12, Jan '14, Jan '15, May '16
|
Quote:
http://faq.ninja250.org/wiki/Servicing_the_swingarm What keeps the rear wheel from sliding back and forth in the swing-arm is the torque of the axle bolt rather than the adjusters. If the axle is loose, the wheel could move slightly forward under acceleration and slightly aft under rear braking. Tighten the axle bolt to 80 ft-lb (108.4 N-m) with the torque wrench on the crown nut and another wrench keeping the head of the bolt from rotating. If you can, use a helper to hold the bike, kick the tire forward at the beginning of tightening and push both wrenches forward at the end, so both adjusters are fully under tension, with no longitudinal play. Your slack should be consistent that way, as the wheel is as forward as the adjusters allow it to be. Then, verify that the alignment of front and rear tires is more or less correct.
__________________________________________________
Motofool .................................Never ride faster than your guardian angel can fly "Mankind is composed of two sorts of men — those who love and create, and those who hate and destroy. Love is the bond between men, the way to teach and the center of the world." - José Martí |
|
|
August 6th, 2016, 03:40 AM | #9 |
ninjette.org member
Name: Rolf
Location: Sweden
Join Date: Jul 2014 Motorcycle(s): Ninja 300 Posts: 70
|
I have had the same experience on the 300, which I think has the same rear suspension. The recommended 20-30 mm is too tight, even if you measure on the tightest part of the chain. 20 mm is definitely too tight.
I am adjusting the chain less tight now, there was a thread about the pregen recommending 35-45 mm, which is about where I'm at. It seems unlikely that the chain could get tighter when warming up. I would expect the opposite, that the swing arm would heat up less than the chain so you get more slack, not less. Assuming they are similar materials, steel in both cases. |
|
August 6th, 2016, 06:18 AM | #10 | |
Rev Limiter
Name: Jay
Location: WI
Join Date: Jul 2013 Motorcycle(s): '06 SV650n, '00 Derbi GPR, '64 CA77 Dream 305, '70 CL450 Scrambler, numerous dirt bikes Posts: A lot.
MOTM - Jun '18, Oct '16
|
Quote:
Get the wheel up in the air and locate the tightest spot - take note of where the valve stem is. That's the most important point, and the place to start. After you have set the slack properly at that point, check every 90 degrees to see how much it changes. If the change is excessive it means there is an issue with the chain or sprockets and it may be time to replace both. |
|
2 out of 2 members found this post helpful. |
August 6th, 2016, 06:23 AM | #11 |
ninjette.org member
Name: Rob
Location: Winnipeg
Join Date: Oct 2014 Motorcycle(s): 2003 ZX12R (sold), 2012 250R, 1975 Honda XL250, 1980 XJ650 Posts: 99
|
The pregen spec is with the bike on the centerstand. Newgen specs are for both wheels on the ground on the sidestand. Don't use a rear stand (spools), your chain will end up too tight just like this situation.
|
3 out of 3 members found this post helpful. |
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Self chain adjustment | Joshua95 | 2008 - 2012 Ninja 250R Tech Talk | 17 | May 12th, 2014 09:12 AM |
Chain Adjustment | reabo | 2008 - 2012 Ninja 250R Tech Talk | 17 | October 3rd, 2013 06:28 AM |
Chain adjustment, now new noise | MagicMike | 2008 - 2012 Ninja 250R Tech Talk | 9 | August 27th, 2013 03:11 PM |
Chain Adjustment | Old Guy on a '08 | 2008 - 2012 Ninja 250R Tech Talk | 21 | October 18th, 2012 05:29 AM |
Chain adjustment | SteveL | General Motorcycling Discussion | 3 | March 21st, 2010 03:08 PM |
|
|