June 20th, 2015, 04:18 PM | #1 |
ninjette.org member
Name: Anon
Location: Midwest
Join Date: Jun 2015 Motorcycle(s): 2006 EX250F Posts: 12
|
Lost carb part, need to find replacement
Hi guys, I bought an 06 Ninja 250 not too long ago and was going through the carbs and I suspect I dropped a piece along the way and I can't find it on the ground. It's part number 9 on the attached image. Is there a place I can buy one of these things? I can't seem to get anything out of google.
Thanks! |
|
June 20th, 2015, 04:21 PM | #2 |
in your machine
Name: Scott
Location: Summer Shade, Ky.
Join Date: Oct 2014 Motorcycle(s): 98 Ninja 250/F12 aka ZX-2R "SERENITY", 91 Ninja 500/A5 aka ZX-5R "Phoenix", 84 Honda GL1200A "SIREN" Posts: A lot.
Blog Entries: 25
MOTM - Jun '17, May '16, Mar '15
|
Send @ducatiman for all your carburetor needs.
__________________________________________________
violente et ignorantia ZX-2R BLOG Twitter and Instagram = Ghostt_Scott I'm not here to change your mind, just to inform. |
|
June 20th, 2015, 04:58 PM | #3 |
ninjette.org certified postwhore
Name: Gordon
Location: new york
Join Date: Sep 2009 Motorcycle(s): '95 DUCATI 900SS/SP '07 DUCATI SS800 '19 HONDA CBR650R Posts: A lot.
MOTM - Nov '18, Mar '17
|
JET-NEEDLE
16017-1326 Your Price: $31.77 ouch....you may choose to check your work area again $12 used on ebay....free shipping from multiple sources search "ex250 needle jet" these are common to all 86-07 Keihin CV carbed 250's..spares should be readily available. |
|
June 21st, 2015, 01:19 PM | #4 |
ninjette.org member
Name: Anon
Location: Midwest
Join Date: Jun 2015 Motorcycle(s): 2006 EX250F Posts: 12
|
Well, thanks for the help buys but I did manage to find it. It was sitting inside of a paper towel that was on the floor. On to the next part of the project, figuring out why only one cylinder is firing. (I'm betting old clapped out spark plugs)
|
|
June 22nd, 2015, 10:04 AM | #5 |
ninjette.org member
Name: Blink
Location: NC
Join Date: Jun 2015 Motorcycle(s): a few Posts: 24
|
I almost lose the same piece, I was blowing off the carb with compressed air and that piece shot across the garage, took me a good hour to find it.
|
|
June 22nd, 2015, 01:38 PM | #6 |
ninjette.org certified postwhore
Name: Gordon
Location: new york
Join Date: Sep 2009 Motorcycle(s): '95 DUCATI 900SS/SP '07 DUCATI SS800 '19 HONDA CBR650R Posts: A lot.
MOTM - Nov '18, Mar '17
|
with the main jet holder (emulsion tube) removed....they sometimes fall out, sometimes hang in when the carbs are tilted right side up.
Very common for these to go MIA and not find their way back in....resulting in major running/starting problems. Their presence should be visibly noted upon both disassembly and reassembly. Especially at $31 each.... jeez Furthermore, I'd suggest cleaning the inner walls of any gook or slime....I routinely treat them in the ultrasonic machine with other stuff. |
|
June 22nd, 2015, 04:06 PM | #7 |
ninjette.org member
Name: Anon
Location: Midwest
Join Date: Jun 2015 Motorcycle(s): 2006 EX250F Posts: 12
|
Yup, I went through each and every part in the carb with cleaner after a soak in pine-sol. Seemed to work for the snowmobiles and it's been recommended over on the ninja 250 wiki. In the interest of not throwing up a bunch of threads, I'm consolidating stuff over to a single thread on this restoration project. It's over here.
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Can't find carb rebuild kit? | redeiko0713 | 2008 - 2012 Ninja 250R Tech Talk | 17 | September 28th, 2013 09:32 PM |
Unknown carb part | dosfiddy | 1986 - 2007 Ninja 250R Tech Talk | 15 | June 12th, 2012 10:10 PM |
Carb Sync Screw Replacement? | MasterCylinder | 1986 - 2007 Ninja 250R Tech Talk | 8 | April 24th, 2012 07:54 AM |
part number/ where to find a... | ninja_thresh_hold | 2008 - 2012 Ninja 250R Tech Talk | 1 | September 30th, 2011 06:37 PM |
Hex Replacement Screws for Carb bowls and tops | g21-30 | 2008 - 2012 Ninja 250R Tech Talk | 2 | June 14th, 2010 06:52 PM |
|
|