October 3rd, 2009, 10:35 AM | #1 |
ninjette.org member
Name: Steve
Location: Kansas city
Join Date: Aug 2009 Motorcycle(s): 94 Ex250 Posts: 101
|
More room at the foot pegs?
So, does anybody have any suggestions for me to get more leg room? I see the 250r guys have something. Im 6'1" and it is kinda cramped...
|
|
October 3rd, 2009, 11:13 AM | #2 |
ninjette.org certified postwhore
Name: Michael
Location: Southern NM
Join Date: Feb 2009 Motorcycle(s): '91 Honda CBR600 F2 Posts: A lot.
|
I know there are a few different types of footpeg lowerers and extenders, I'm just not sure where to find them. Search around a bit and you should be able to find them.
__________________________________________________
1991 Honda CBR600 F2, White/Gray, D&D slip-on exhaust, tail integrator, gel grips, Custom undertail. |
|
October 3rd, 2009, 11:15 AM | #3 |
ninjette.org certified postwhore
Name: Travis
Location: Warwick, RI
Join Date: Apr 2009 Motorcycle(s): 2009 Ninja 250R Posts: A lot.
|
One guy used Buell pegs. http://www.ninjette.org/forums/showt...ght=buell+pegs
But it was on a new-gen
__________________________________________________
Addicted to anything that has an engine and rolls. |
|
October 4th, 2009, 07:49 PM | #4 |
ninjette.org member
Name: Jerry
Location: California
Join Date: Jun 2009 Motorcycle(s): 2007 EX250 Posts: 178
|
I'd try to raise the seat, not lower the pegs.
Bead riders, sheepskin, Airhawks will all give you a 1/2 inch to an inch more room. Here's a link from another board...there may be some ideas in there. http://faq.ninja250.org/wiki/Bodywork_%26_Frame |
|
November 19th, 2009, 04:03 PM | #5 |
ninjette.org member
Name: Steve
Location: Kansas city
Join Date: Aug 2009 Motorcycle(s): 94 Ex250 Posts: 101
|
any other suggestions???
|
|
November 20th, 2009, 04:48 AM | #6 |
ninjette.org member
Name: terry
Location: SW fla
Join Date: Sep 2009 Motorcycle(s): 2007 250r Posts: 94
|
I have the same problem. I only see about 1.5 to 2" of room to move down.
Might need to make different mounts for the pegs and controls. |
|
November 20th, 2009, 01:45 PM | #7 |
ninjette.org newbie
Name: Marrs
Location: Tulare
Join Date: Aug 2009 Motorcycle(s): '07 250 Posts: 4
|
You might need to do both, move the seat height up with a custom seat or seat pad and move the pegs down and back with a rearset to get much of a noticeable difference. I believe woodcraft makes rearsets that will give you more room.
|
|
November 20th, 2009, 03:18 PM | #8 |
ninjette.org member
Name: Steve
Location: Kansas city
Join Date: Aug 2009 Motorcycle(s): 94 Ex250 Posts: 101
|
|
|
January 16th, 2010, 11:11 AM | #9 |
ninjette.org member
Name: Steve
Location: Kansas city
Join Date: Aug 2009 Motorcycle(s): 94 Ex250 Posts: 101
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
How to raised foot pegs? | caineroad | General Motorcycling Discussion | 4 | November 6th, 2013 03:23 PM |
Question about foot pegs. | Hawk637 | General Motorcycling Discussion | 5 | April 19th, 2011 10:22 AM |
aftermarket foot pegs? | RRTRIDER | 2008 - 2012 Ninja 250R Farkles | 14 | December 6th, 2009 11:28 AM |
Grinding Foot Pegs | jonb08 | 1986 - 2007 Ninja 250R Tech Talk | 14 | June 17th, 2009 06:57 PM |
Aftermarket Foot Pegs | Shift250R | 2008 - 2012 Ninja 250R Farkles | 142 | May 11th, 2009 11:00 AM |
|
|