|
November 27th, 2013, 03:05 PM
|
#1 |
|
ninjette.org member
Name: steve
Location: Half Moon Bay, CA
Join Date: Apr 2013 Motorcycle(s): 02 ex250, 07 HD xl1200n, 69 ct90 Posts: 28
|
Quick ? regarding carb diaphragm
does it matter if the little holes face the back or the front?
TY Steve |
|
|
|
November 27th, 2013, 05:29 PM
|
#2 |
|
Daily Ninjette rider
Name: Hernan
Location: Florida
Join Date: Mar 2011 Motorcycle(s): 2007 Ninja 250 Posts: A lot.
MOTY - 2016, MOTM - Dec '12, Jan '14, Jan '15, May '16
|
What little holes are you asking about?
__________________________________________________
Motofool  .................................Never ride faster than your guardian angel can fly "Mankind is composed of two sorts of men — those who love and create, and those who hate and destroy. Love is the bond between men, the way to teach and the center of the world." - José Martí |
|
|
|
|
November 27th, 2013, 05:42 PM
|
#3 |
|
ninjette.org member
Name: steve
Location: Half Moon Bay, CA
Join Date: Apr 2013 Motorcycle(s): 02 ex250, 07 HD xl1200n, 69 ct90 Posts: 28
|
The little holes in the bottom next to where the needles go through the diaphragm... Doesn't matter now I faced them towards the air filters and it's running great. TY for the response.
|
|
|
|
|
March 22nd, 2015, 07:22 AM
|
#4 |
|
ninjette.org sage
Name: michael
Location: Central Georgia
Join Date: May 2013 Motorcycle(s): 2019 Ninja 400, Sold 2012 Ninja 650, Sold 2009 Ninja 250r, Sold 2007 DRZ400s Posts: 628
|
So I know op said his was fine, but is there a correct side for the hole in the bottom of the slide near the needle?
|
|
|
|
|
March 23rd, 2015, 10:05 AM
|
#5 |
|
ninjette.org sage
Name: bob
Location: Earf
Join Date: Apr 2013 Motorcycle(s): 2005 Ninja 250, 2006 SV650N Posts: 642
|
I'm actually kind of curious about this as well. Given the setup I don't think it would make a difference but I made sure the holes pointed towards the sync screw on the carbs like they did when I pulled them out.
|
|
|
|
 |
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| carb diaphragm | triumphtriple | Items Wanted | 1 | May 1st, 2014 06:42 PM |
| Carb diaphragm install | nick5446 | 2008 - 2012 Ninja 250R Tech Talk | 5 | June 4th, 2013 02:50 PM |
| Carb Diaphragm Accident! | Trainsk8 | 2008 - 2012 Ninja 250R Tech Talk | 2 | May 19th, 2012 12:08 PM |
| Sounds (Testing) of Good & Bad CV Carb Diaphragm | g21-30 | 2008 - 2012 Ninja 250R Tech Talk | 4 | September 28th, 2011 08:35 AM |
| Carb Diaphragm Melted | NaughtyusMaximus | 2008 - 2012 Ninja 250R Tech Talk | 17 | July 25th, 2009 11:45 AM |
|
|
