HID PnP Kit With Angel Eyes

wayanlam · July 22nd, 2011, 09:28 AM

too late to put in comments, but ill post up the pics for now

added the comments now~

my bike went thru a small "stripping" after i dropped her a couple months ago, decided to kep her naked. made this DIY quite easy. but that means that for yall that were to install this on the full faring bike would need to read up another DIY if you are not familiar with the faring removal.

OEM headlamp out

HID kit headlamp in... took all of about 2 minutes, hehe, beat that you full faring people!

this is the Low and High beam controller. there is no splicing required, just plug them in

one into the low beam, and the other set into the high beam. black (ground) into Black! im not sure what happens if you get this back to front, might end up with the beams back to front, in which case i would suggest that its swapped the right way around.

seal and tape these plugs in securely, both to keep water out, and also so that they don't accidentally slip out. electrical tape would do the job.

the other end plugs into the controller

here its plugged in, next step:

the 2 inverters for the angel eye bulbs.

with the indonesian model bikes, you can hook this up the "caution" light, but that doesnt exist in the US model bikes, you would need to pull in or splice a new power line, possibly with a switch that you can fix to the handlebar or somewhere. not sure where would be the best place to splice it in, since you want it to turn off when the bike is off. any electricians in the house?

plug the other end into the provided wire that comes out of the headlamp

there, the angel eyes are working.
these are blue only, i think you can also request other colors. and i have read an article where they are starting to introduce multi colored angel eyes, that you can set with a remote. something to look forward to in the near future i guess.

from the controller there is the power cable, with a fuse built in.

that is hooked up to the positive (+) end of the battery.

the ground cables are on the tip of the other 2 cables that come out of the controller that plugs into the HID balast.

plug in the balast.

o ya, make sure its grounded. i just fixed them to the metal headlamp frame that i fabricated. with the full faring bikes, you can fix it (securely) to most parts of the bike that is in contact with the bikes frame, thats all grounded (-)

plug these in

these are the controllers for the Low/High beam shutters in the projector.

plug in the power from the balast to the plugs that come out of the headlamp.

there are 4 cables coming out of each projector (total 8). 2 cables are the (+) and (-) from the balanst for the HID bulb. 1 cable is for the angel eyes, and 1 cable is for the low/high beam shutter.

off,

angel eyes "aka caution light"

low beam on,

High beam... ya, barely noticeable in the pics, can see it much better on the youtube video i posted.

http://youtu.be/sMfT26x57QE

still dont know how to imbed videos. and still too lazy to read it up, lol...

and again in the dark that i took when i got home from dinner, hehe

so basically im posting this up so the person that ordered this headlamp from me can look it up when it arrives and have an easy way to follow some sort of instructions step by step.

obviously you will need to deal with all the farings and where to fix the various balasts, controllers and the inverter. most people here use silicon glue and glue them into the inside of the farings where they dont get in the way. be creative, hehe.

thats all for now, hope these pictures speak for themselves, hehe

caps · July 22nd, 2011, 10:17 AM

um...

how much?

JBedney · July 22nd, 2011, 10:43 AM

Manufacturer?

Kit part number?

Who sells the kit?

LiquidBiohazard · July 22nd, 2011, 12:05 PM

This is so cool!!

Where did you get it and how much?

Also, do the HALO rings change colors? And can you get bi-xenon so both lights are on and there is an actuated cut off for high beam?

bob706 · July 22nd, 2011, 12:20 PM

Looks awesome

kaiserz · July 22nd, 2011, 12:29 PM

sweet mother! that looks awesome!

setasai · July 22nd, 2011, 12:37 PM

That looks so sweet but why do i get the feeling it's going to become a wiring mess back there?

gt_turbo · July 22nd, 2011, 12:44 PM

do i hear GB? LOL send some over here!

caps · July 22nd, 2011, 12:48 PM

Quote:

Originally Posted by setasai

That looks so sweet but why do i get the feeling it's going to become a wiring mess back there?

I'm wondering where he is gonna fit it all

setasai · July 22nd, 2011, 12:57 PM

Quote:

Originally Posted by caps

I'm wondering where he is gonna fit it all

I think it would be pretty cool if all of those parts and wires could be stripped from their respective casings and put into a box with only the relevant wires coming out to connect the thing and possibly mount it to the frame in one piece.

Merc250r · July 22nd, 2011, 02:06 PM

lot's of velcro and zip ties. Nice job I wonder how much and when I can make this purchase

alex.s · July 22nd, 2011, 02:16 PM

are they real projectors? or are they like those ebay mcfakey 'look like projectors but are really just reflectors'? also where do we buy them?

can we see pics of what they look like against a wall?

p.s. all hail the great wayan. bringer of amazement and joy across the land!

Merc250r · July 22nd, 2011, 02:42 PM

Quote:

Originally Posted by alex.s

are they real projectors? or are they like those ebay mcfakey 'look like projectors but are really just reflectors'? also where do we buy them?

can we see pics of what they look like against a wall?

p.s. all hail the great wayan. bringer of amazement and joy across the land!

His location: Indonesia

wayanlam · July 22nd, 2011, 05:41 PM

been trying to upload 2 HD vids onto youtube since last night, but the damn slow internet upload speed here is giving me grief! you can see from there that both lights are on (for both high, and low beam) and that it has the proper projector cutoff mechanism. so both lights are low, and high beams.

will post the link once it eventually uploads later.

going to work now

wayanlam · July 22nd, 2011, 05:54 PM

got another mod that ill be posting shortly that should make some ppl happy too

rusninja · July 22nd, 2011, 05:59 PM

what is it :O

wayanlam · July 22nd, 2011, 06:36 PM

Quote:

Originally Posted by rusninja

what is it :O

http://www.ninjette.org/forums/showp...2&postcount=20

its there

wayanlam · July 22nd, 2011, 08:45 PM

allright, so one movie finally finished uploading, 150 Mb for 45 seconds, lol... damn HD quality takes for ever to upload

http://youtu.be/sMfT26x57QE

i got another vid uploading when it was later in the evening when it was dark.

that will take another 5 hours to upload that xD

alex.s · July 22nd, 2011, 08:46 PM

shcweeeeet!!

alex.s · July 22nd, 2011, 08:47 PM

mind if i ask how much they set you back?

wayanlam · July 22nd, 2011, 09:10 PM

around $550 for the complete set, including a new OEM reflector.

about $300 without the reflector, so just all the HID kit parts.

leed · July 23rd, 2011, 07:51 AM

Those angel eyes look pretty good. I thought about putting them in mine.. But I decided against it :P

kaiserz · July 23rd, 2011, 11:56 AM

Quote:

Originally Posted by wayanlam

http://www.ninjette.org/forums/showp...2&postcount=20

its there

SWEET MOTHER!! I WANT ONE !

heheh

wayanlam · July 23rd, 2011, 11:32 PM

http://youtu.be/YQtj7N4DmFQ

thats the vid of the lights in the dark

finally finished uploading it, lol

July 22nd, 2011, 09:28 AM	#1
wayanlam ninjette.org certified postwhore Name: Wayan Location: Bali - Indonesia Join Date: Apr 2009 Motorcycle(s): 2014 Z250 Posts: A lot.	HID PnP Kit With Angel Eyes too late to put in comments, but ill post up the pics for now added the comments now~ my bike went thru a small "stripping" after i dropped her a couple months ago, decided to kep her naked. made this DIY quite easy. but that means that for yall that were to install this on the full faring bike would need to read up another DIY if you are not familiar with the faring removal. OEM headlamp out HID kit headlamp in... took all of about 2 minutes, hehe, beat that you full faring people! this is the Low and High beam controller. there is no splicing required, just plug them in one into the low beam, and the other set into the high beam. black (ground) into Black! im not sure what happens if you get this back to front, might end up with the beams back to front, in which case i would suggest that its swapped the right way around. seal and tape these plugs in securely, both to keep water out, and also so that they don't accidentally slip out. electrical tape would do the job. the other end plugs into the controller here its plugged in, next step: the 2 inverters for the angel eye bulbs. with the indonesian model bikes, you can hook this up the "caution" light, but that doesnt exist in the US model bikes, you would need to pull in or splice a new power line, possibly with a switch that you can fix to the handlebar or somewhere. not sure where would be the best place to splice it in, since you want it to turn off when the bike is off. any electricians in the house? plug the other end into the provided wire that comes out of the headlamp there, the angel eyes are working. these are blue only, i think you can also request other colors. and i have read an article where they are starting to introduce multi colored angel eyes, that you can set with a remote. something to look forward to in the near future i guess. from the controller there is the power cable, with a fuse built in. that is hooked up to the positive (+) end of the battery. the ground cables are on the tip of the other 2 cables that come out of the controller that plugs into the HID balast. plug in the balast. o ya, make sure its grounded. i just fixed them to the metal headlamp frame that i fabricated. with the full faring bikes, you can fix it (securely) to most parts of the bike that is in contact with the bikes frame, thats all grounded (-) plug these in these are the controllers for the Low/High beam shutters in the projector. plug in the power from the balast to the plugs that come out of the headlamp. there are 4 cables coming out of each projector (total 8). 2 cables are the (+) and (-) from the balanst for the HID bulb. 1 cable is for the angel eyes, and 1 cable is for the low/high beam shutter. off, angel eyes "aka caution light" low beam on, High beam... ya, barely noticeable in the pics, can see it much better on the youtube video i posted. http://youtu.be/sMfT26x57QE still dont know how to imbed videos. and still too lazy to read it up, lol... and again in the dark that i took when i got home from dinner, hehe so basically im posting this up so the person that ordered this headlamp from me can look it up when it arrives and have an easy way to follow some sort of instructions step by step. obviously you will need to deal with all the farings and where to fix the various balasts, controllers and the inverter. most people here use silicon glue and glue them into the inside of the farings where they dont get in the way. be creative, hehe. thats all for now, hope these pictures speak for themselves, hehe __________________________________________________ Kawasaki Z250, Bored up to 300cc with 12.8 CR, 41hp at wheel 27nm torque, Two bros full exhaust with DB killer Dynojet Power Commander V, KnN Open filter, intake and exhaust ported, Puig Windshield Last futzed with by wayanlam; July 23rd, 2011 at 02:53 AM.

July 22nd, 2011, 10:17 AM	#2
caps Sexy Beast Name: Mat Location: Tampa Join Date: Mar 2011 Motorcycle(s): 2010 Ninja 250R, 2006 ZX-14, 2012 Ducati Monster Posts: A lot.	um... how much? __________________________________________________ 2010 Ninja 250 2006 Ninja ZX-14 ^Both Links

July 22nd, 2011, 02:16 PM	#12
alex.s wat Name: wat Location: tustin/long beach Join Date: Sep 2009 Motorcycle(s): wat Posts: Too much. Blog Entries: 5 MOTM - Oct '12, Feb '14	are they real projectors? or are they like those ebay mcfakey 'look like projectors but are really just reflectors'? also where do we buy them? can we see pics of what they look like against a wall? p.s. all hail the great wayan. bringer of amazement and joy across the land! __________________________________________________

July 22nd, 2011, 05:41 PM	#14
wayanlam ninjette.org certified postwhore Name: Wayan Location: Bali - Indonesia Join Date: Apr 2009 Motorcycle(s): 2014 Z250 Posts: A lot.	been trying to upload 2 HD vids onto youtube since last night, but the damn slow internet upload speed here is giving me grief! you can see from there that both lights are on (for both high, and low beam) and that it has the proper projector cutoff mechanism. so both lights are low, and high beams. will post the link once it eventually uploads later. going to work now __________________________________________________ Kawasaki Z250, Bored up to 300cc with 12.8 CR, 41hp at wheel 27nm torque, Two bros full exhaust with DB killer Dynojet Power Commander V, KnN Open filter, intake and exhaust ported, Puig Windshield

July 22nd, 2011, 05:54 PM	#15
wayanlam ninjette.org certified postwhore Name: Wayan Location: Bali - Indonesia Join Date: Apr 2009 Motorcycle(s): 2014 Z250 Posts: A lot.	got another mod that ill be posting shortly that should make some ppl happy too __________________________________________________ Kawasaki Z250, Bored up to 300cc with 12.8 CR, 41hp at wheel 27nm torque, Two bros full exhaust with DB killer Dynojet Power Commander V, KnN Open filter, intake and exhaust ported, Puig Windshield

July 22nd, 2011, 10:43 AM	#3
JBedney ninjette.org member Name: John Location: California Join Date: Aug 2010 Motorcycle(s): Ninja 250R Posts: 34	Manufacturer? Kit part number? Who sells the kit?

July 22nd, 2011, 12:05 PM	#4
LiquidBiohazard ninjette.org member Name: Dave Location: Surrey, BC Join Date: Jul 2011 Motorcycle(s): 2011 Kawasaki Ninja 250R Posts: 36	This is so cool!! Where did you get it and how much? Also, do the HALO rings change colors? And can you get bi-xenon so both lights are on and there is an actuated cut off for high beam?

July 22nd, 2011, 12:20 PM	#5
bob706 ninjette.org certified postwhore Name: Sean Location: Mary Esther, FL Join Date: Jan 2009 Motorcycle(s): 2008 Ninja 250 1998 HD Road King Posts: A lot.	Looks awesome

July 22nd, 2011, 12:29 PM	#6
kaiserz There's a limit to s2pdty Name: A.D. Location: NoVa the burg Join Date: Apr 2011 Motorcycle(s): 250r ninja (sold) Posts: A lot.	sweet mother! that looks awesome!

July 22nd, 2011, 12:37 PM	#7
setasai ninjette.org certified postwhore Name: Brian Location: Detroit, MI Join Date: Jun 2010 Motorcycle(s): 2009 Ninja 250R Green Posts: A lot.	That looks so sweet but why do i get the feeling it's going to become a wiring mess back there?

July 22nd, 2011, 12:44 PM	#8
gt_turbo ninjette.org sage Name: L Location: WI Join Date: Apr 2011 Motorcycle(s): '09 250R, '13 CBR500R Posts: 709	do i hear GB? LOL send some over here!

July 22nd, 2011, 02:06 PM	#11
Merc250r ninjette.org member Name: Murad Location: Orlando fl Join Date: Jul 2011 Motorcycle(s): 2011 Yamaha FZ6R Posts: 84	lot's of velcro and zip ties. Nice job I wonder how much and when I can make this purchase

July 22nd, 2011, 05:59 PM	#16
rusninja Ninjette wanabe :D Name: Ruslan Location: San Jose Join Date: Apr 2011 Motorcycle(s): white 300 :D Posts: A lot.	what is it :O __________________________________________________ VROOOM vrooom >.>

July 22nd, 2011, 08:45 PM	#18
wayanlam ninjette.org certified postwhore Name: Wayan Location: Bali - Indonesia Join Date: Apr 2009 Motorcycle(s): 2014 Z250 Posts: A lot.	allright, so one movie finally finished uploading, 150 Mb for 45 seconds, lol... damn HD quality takes for ever to upload http://youtu.be/sMfT26x57QE i got another vid uploading when it was later in the evening when it was dark. that will take another 5 hours to upload that xD __________________________________________________ Kawasaki Z250, Bored up to 300cc with 12.8 CR, 41hp at wheel 27nm torque, Two bros full exhaust with DB killer Dynojet Power Commander V, KnN Open filter, intake and exhaust ported, Puig Windshield

July 22nd, 2011, 08:46 PM	#19
alex.s wat Name: wat Location: tustin/long beach Join Date: Sep 2009 Motorcycle(s): wat Posts: Too much. Blog Entries: 5 MOTM - Oct '12, Feb '14	shcweeeeet!! __________________________________________________

July 22nd, 2011, 08:47 PM	#20
alex.s wat Name: wat Location: tustin/long beach Join Date: Sep 2009 Motorcycle(s): wat Posts: Too much. Blog Entries: 5 MOTM - Oct '12, Feb '14	mind if i ask how much they set you back? __________________________________________________

July 22nd, 2011, 09:10 PM	#21
wayanlam ninjette.org certified postwhore Name: Wayan Location: Bali - Indonesia Join Date: Apr 2009 Motorcycle(s): 2014 Z250 Posts: A lot.	around $550 for the complete set, including a new OEM reflector. about $300 without the reflector, so just all the HID kit parts. __________________________________________________ Kawasaki Z250, Bored up to 300cc with 12.8 CR, 41hp at wheel 27nm torque, Two bros full exhaust with DB killer Dynojet Power Commander V, KnN Open filter, intake and exhaust ported, Puig Windshield

July 23rd, 2011, 07:51 AM	#22
leed ninjette.org sage Name: David Location: Loves Park, IL Join Date: Feb 2011 Motorcycle(s): Time will tell Posts: 969	Those angel eyes look pretty good. I thought about putting them in mine.. But I decided against it :P

July 23rd, 2011, 11:32 PM	#24
wayanlam ninjette.org certified postwhore Name: Wayan Location: Bali - Indonesia Join Date: Apr 2009 Motorcycle(s): 2014 Z250 Posts: A lot.	http://youtu.be/YQtj7N4DmFQ thats the vid of the lights in the dark finally finished uploading it, lol __________________________________________________ Kawasaki Z250, Bored up to 300cc with 12.8 CR, 41hp at wheel 27nm torque, Two bros full exhaust with DB killer Dynojet Power Commander V, KnN Open filter, intake and exhaust ported, Puig Windshield

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
HOW-TO: Install BKMOTO BiXenon HID projectors with angel eyes halos 2008+ Ninja 250R	borka	2008 - 2012 Ninja 250R Farkles	66	March 3rd, 2015 09:46 AM
Angel Eyes and/or Halo Kit	JulioXa	2008 - 2012 Ninja 250R Farkles	4	February 23rd, 2012 01:28 PM