July 20th, 2021, 11:00 AM | #1 |
ninjette.org member
Name: Steve
Location: Fort Wayne
Join Date: Jun 2021 Motorcycle(s): 2009 Ninja 250r Posts: 14
|
Symptoms of a bad Fuel screw Adjustment
I was wondering if anyone could explain the symptoms of a bad Fuel Screw Adjustment, How would the bike run at different RPM's if they are too tight, or too loose.
|
|
July 20th, 2021, 12:16 PM | #2 |
Guy Who Enjoys Riding
Name: Jim
Location: North Carolina
Join Date: Jul 2016 Motorcycle(s): Ninja 250 Posts: A lot.
MOTM - Oct '18, Aug '17, Aug '16
|
The mixture screw adjusts idle mixture (closed throttle) only. Starting and idling are affected by the adjustment of these two screws of the two carburetors. They should be adjusted for fastest idle speed, plus maybe a tiny bit richer (more counterclockwise).
|
1 out of 1 members found this post helpful. |
July 20th, 2021, 01:17 PM | #3 |
in your machine
Name: Scott
Location: Summer Shade, Ky.
Join Date: Oct 2014 Motorcycle(s): 98 Ninja 250/F12 aka ZX-2R "SERENITY", 91 Ninja 500/A5 aka ZX-5R "Phoenix", 84 Honda GL1200A "SIREN" Posts: A lot.
Blog Entries: 25
MOTM - Jun '17, May '16, Mar '15
|
I'm personally curious about why the question ❓ us the OP having issues?
__________________________________________________
violente et ignorantia ZX-2R BLOG Twitter and Instagram = Ghostt_Scott I'm not here to change your mind, just to inform. |
|
July 20th, 2021, 01:28 PM | #4 | |
ninjette.org member
Name: Steve
Location: Fort Wayne
Join Date: Jun 2021 Motorcycle(s): 2009 Ninja 250r Posts: 14
|
Quote:
hard to describe but say around 20-30 mph, or say 15-20% throttle the bike doesnt hold a consistant speed. almost like its pulsing . Before swaping out a hose on the bike wich finally led to the fix, i was playing around with my mix screws, and didnt know if a bad mix could lead to these problems. Also to note the bike runs better on choke then without making me suspect im too lean or rich |
|
|
July 20th, 2021, 02:25 PM | #5 |
Guy Who Enjoys Riding
Name: Jim
Location: North Carolina
Join Date: Jul 2016 Motorcycle(s): Ninja 250 Posts: A lot.
MOTM - Oct '18, Aug '17, Aug '16
|
That's into the needle-needlejet circuit. Mine was exactly like that when I got it, with surging at steady running speeds. I shimmed the needles something like 1/2 a millimeter and it cured it. When Ducatiman restored my carbs to new condition he asked if I wanted to keep the shims and I said no. When I got them back and installed them, EVERYTHING about the carbs and fueling was perfect and no shims were needed. I assume there was some varnish or other obstruction in the needle jet circuit that he removed.
|
1 out of 1 members found this post helpful. |
July 21st, 2021, 07:24 AM | #6 |
Rev Limiter
Name: Jay
Location: WI
Join Date: Jul 2013 Motorcycle(s): '06 SV650n, '00 Derbi GPR, '64 CA77 Dream 305, '70 CL450 Scrambler, numerous dirt bikes Posts: A lot.
MOTM - Jun '18, Oct '16
|
Start with your Idle Mixture Screws about 2.5 turns out. That should get you close if everything else is right.
Set it precisely after a ride, when the engine is at operating temp. The adjustment can change, depending on air temp and fuel type (% of ethanol). As TJ said - highest RPMs + about 1/8 richer (out) is my method. Reset the idle speed to about 1300 when you are done. Also sync the carbs if you haven't, then redo the mixture setting. Lots of info in this section -https://faq.ninja250.org/wiki/Intake |
|
July 21st, 2021, 09:02 AM | #7 |
ninjette.org member
Name: Steve
Location: Fort Wayne
Join Date: Jun 2021 Motorcycle(s): 2009 Ninja 250r Posts: 14
|
thanks for the heads up guys! ill give it a go ill play with them some more! I'll look to send em his way towards the end of the season so i can take advantage of the gas mileage while i still can. My truck is killing me with like 12 MPG lolol
|
|
July 21st, 2021, 09:06 AM | #8 |
Guy Who Enjoys Riding
Name: Jim
Location: North Carolina
Join Date: Jul 2016 Motorcycle(s): Ninja 250 Posts: A lot.
MOTM - Oct '18, Aug '17, Aug '16
|
|
|
July 21st, 2021, 09:35 AM | #9 |
Rev Limiter
Name: Jay
Location: WI
Join Date: Jul 2013 Motorcycle(s): '06 SV650n, '00 Derbi GPR, '64 CA77 Dream 305, '70 CL450 Scrambler, numerous dirt bikes Posts: A lot.
MOTM - Jun '18, Oct '16
|
Sending them to ducatiman will end any concern about carb issues for you.
|
|
July 21st, 2021, 10:14 AM | #10 |
ninjette.org member
Name: Steve
Location: Fort Wayne
Join Date: Jun 2021 Motorcycle(s): 2009 Ninja 250r Posts: 14
|
Thanks guys! i just reached out will be doing this
|
|
August 24th, 2021, 07:42 PM | #11 |
Retired motorcycle Mc.
Name: Robert
Location: Weed, California.
Join Date: Jul 2021 Motorcycle(s): 2012 Kawasaki Ninja 250R, 2021 CSC TT250, 1977 Triumph Bonneville 750cc,2001 Honda XR650L. Posts: A lot.
|
I've noticed a slight surging on my Ninja as well, it has a after market muffler
on it but everything but the gearing in the rear is original.... those air screws are next to impossible to adjust... so I suspect them not being perfect..... but that wouldn't effect the surging in and about 4 grand... and that is what I am experiencing. I'm wondering if Jims shimming up the jet needles would cure this ? Bob......
__________________________________________________
Its too late when you've gone too far ! |
|
August 24th, 2021, 08:20 PM | #12 |
Guy Who Enjoys Riding
Name: Jim
Location: North Carolina
Join Date: Jul 2016 Motorcycle(s): Ninja 250 Posts: A lot.
MOTM - Oct '18, Aug '17, Aug '16
|
|
1 out of 1 members found this post helpful. |
August 24th, 2021, 11:03 PM | #13 |
Retired motorcycle Mc.
Name: Robert
Location: Weed, California.
Join Date: Jul 2021 Motorcycle(s): 2012 Kawasaki Ninja 250R, 2021 CSC TT250, 1977 Triumph Bonneville 750cc,2001 Honda XR650L. Posts: A lot.
|
understood ! I'm thinking my carb cleaning wasn't as good as it could have been now...
I have to take the right side fairing off to replace the crushed turn signal I did today... so I might go ahead and pull the other side and pull the carbs too.... .....I doubt it though I got alot of yard stuff I gott'a do coming tomorrow I have a pallet load of 2' pavers to put in as our patio, so I'll be busy with that ... the bike can wait. ( it's a toy after all ! LOL) I did buy a rear lowering kit for the thing but it won't be here for a month or two.... it's fully adjustable so I can set it at the height I want. that was one of the reasons I dropped the bike today... it's too tall for my short legs ! LOL.... that and not having been on a bike in such a long time... but I'll never admit that ! LOL at least the scratches aren't real deep ! LOL ..... Bob........
__________________________________________________
Its too late when you've gone too far ! |
|
August 25th, 2021, 06:06 AM | #14 |
Rev Limiter
Name: Jay
Location: WI
Join Date: Jul 2013 Motorcycle(s): '06 SV650n, '00 Derbi GPR, '64 CA77 Dream 305, '70 CL450 Scrambler, numerous dirt bikes Posts: A lot.
MOTM - Jun '18, Oct '16
|
|
|
August 25th, 2021, 06:28 AM | #15 |
Retired motorcycle Mc.
Name: Robert
Location: Weed, California.
Join Date: Jul 2021 Motorcycle(s): 2012 Kawasaki Ninja 250R, 2021 CSC TT250, 1977 Triumph Bonneville 750cc,2001 Honda XR650L. Posts: A lot.
|
indeed... I've never shimmed a needle yet in all my years simply because that would mess up the 14:1 fuel to air ratio that the carb was designed to deliver
...but if it's not quite right maybe a band-aid would work ...LOL Bob.....
__________________________________________________
Its too late when you've gone too far ! |
|
August 25th, 2021, 08:06 AM | #16 |
ninjette.org certified postwhore
Name: AKA JacRyann
Location: Mesa, AZ
Join Date: Dec 2011 Motorcycle(s): CB125T CBR250R-MC19 CBR250RR-MC22 NSR350R-MC21 VF500F CBR600RR SFV650 VFR750F R1M ST1300PA Valkyrie-F6C Posts: A lot.
MOTY - 2018, MOTM - Nov '17
|
Yeah, band-aids don't really "fix" actual problems, just cover up symptoms.
Due to increased use of ethanol petrol thanks to corn-lobby, there's more issues with corrosion in carbs. In addition to previous dried petrol deposits. Spray carb cleaners no longer work due to removal of chlorinated compounds. These bikes ran perfectly when new leaving showroom floor. There's absolutely zero reason they won't run like that again if carbs are factory-fresh clean. In order to restore carbs to that condition, you'll need to do: - complete disassembly to every last nut, bolt, O-ring and individual components - scrub all parts by hand with various solvents (PEA-based ones work best) - scrub petrol passages from tank to intake-valves with brushes of matching sizes - ultrasonic soak - micro soda-blast - replace all rubbers, float-valves, float-bowl seals, fuel-rail O-rings, slide-diaphragms if needed - re-assemble If you don't have all this equipment and don't want to buy them all to restore one set of carbs to factory-fresh clean, then you won't get bike that runs like brand-new. Easier to send them to someone who has this equipment and experience to do restoration work to factory-fresh clean condition... |
1 out of 1 members found this post helpful. |
August 25th, 2021, 09:39 AM | #17 |
ninjette.org certified postwhore
Name: Gordon
Location: new york
Join Date: Sep 2009 Motorcycle(s): '95 DUCATI 900SS/SP '07 DUCATI SS800 '19 HONDA CBR650R Posts: A lot.
MOTM - Nov '18, Mar '17
|
agreed there is no substitute for (nor compensating for) *truly* clean, well set up carbs. Imperative starting point. Ditto petcock.
__________________________________________________
gordon@customcarbservices.com Custom Carb Service www.customcarbservices.com |
|
August 25th, 2021, 11:25 AM | #18 | |
Rev Limiter
Name: Jay
Location: WI
Join Date: Jul 2013 Motorcycle(s): '06 SV650n, '00 Derbi GPR, '64 CA77 Dream 305, '70 CL450 Scrambler, numerous dirt bikes Posts: A lot.
MOTM - Jun '18, Oct '16
|
Quote:
Luckily, we have ducatiman... |
|
3 out of 3 members found this post helpful. |
August 29th, 2021, 05:30 PM | #19 |
Retired motorcycle Mc.
Name: Robert
Location: Weed, California.
Join Date: Jul 2021 Motorcycle(s): 2012 Kawasaki Ninja 250R, 2021 CSC TT250, 1977 Triumph Bonneville 750cc,2001 Honda XR650L. Posts: A lot.
|
to answer the original question, symptoms of a bad fuel adjustment (screw)
I would have to say this, most times it is difficult to tell if their out of adjustment with one another, But in extreme cases, it's fairly easy... you can hear it as it idles in the case of my 250R it was very apparent as it would not idle on both cylinders when the engine was cold... In most cases though you can hear it as one cylinder will be heavier than the other, the boom is a bit louder or stronger than the next boom.... in most cases this is all you have to go by until you put the wrenches to it. keep in mind the fuel air screws do Not effect the running of the engine above an idle if it's idling at 800RPM the most it will effect the running is about 1200 rpm lean Fuel air screw adjustment will result in a Sogg when cracking the throttle open. if they are too rich in adjustment it will smoke black smoke at idle. which is bad as it will foul the spark plugs quickly.... You are supposed to adjust the air fuel screws when the engine is warm and ready to go... not cold ! and you adjust then to the fastest idle you can get by continuously dropping the idle speed ( knob on the side) to as slow an idle as you can get, say 500 RPM ... no lower than that. if you adjust the left cylinder to max RPM then you need to drop the idle to 500~800 RPM and adjust the right cylinder the same way, once your sure you have the maximum RPM on each air screw then you should turn them out about 1/8th turn each More... this will set the Fuel/Air adjustment just right for Idle. it should take any throttle change with out stumbling , it will grab the RPM's fast and without hesitation if it's done right.... this of course assumes the carbs are clean and in good working order, if the bike has been setting all winter with gas in it and it doesn't want to idle like it did before you parked it chances are real good you have to clean the carburetors to get it working properly again... using a gasoline stabilizer is a real good idea in the winter but better yet I like to shut off the fuel and run the bike till it is out of fuel in the carburetors as well... but with the vacuum petcock that is impossible to do...you can't shut off the fuel if you wanted to. only by pulling the vacuum line to the petcock and plugging it can you actually turn off the gas... but if your vacuum diaphragm leaks gas to the carbs like mine does anyway, that isn't going to help at all. Up to this date I have always just started every motor on the property at least every 4 to 6 weeks during the winter, I also like to add a little chainsaw gas ( gasoline and 2 cycle oil mix) to the engine's gas tank to help stabilize the fuel, this has never failed me and I've not had to clean the carbs on anything in the 5 years I've been here. but I do start the motors about every month and run them till their good and warm then turn them off. this is what I do... I don't buy fuel stabilizers, I just add chainsaw gas to the tank.... if your worried about a catalytic converter perhaps you shouldn't do that !!!! because chainsaw gas and catalytic converters don't mix well, it'll plug them up fast ! .... But the Fuel Air screws under the carb are for Idle Only, they don't adjust the speed of the idle, they adjust the Fuel / Air mixture, the speed is adjusted by changing the butter fly stop screw ( the knob on the Ninja.) .... Bob...
__________________________________________________
Its too late when you've gone too far ! |
|
August 29th, 2021, 06:52 PM | #20 | |
ninjette.org certified postwhore
Name: AKA JacRyann
Location: Mesa, AZ
Join Date: Dec 2011 Motorcycle(s): CB125T CBR250R-MC19 CBR250RR-MC22 NSR350R-MC21 VF500F CBR600RR SFV650 VFR750F R1M ST1300PA Valkyrie-F6C Posts: A lot.
MOTY - 2018, MOTM - Nov '17
|
Quote:
Any other issues after that in off-idle transition or mid-range is due to insufficiently cleaned secret hidden passages in carbs. Jets are just first 5% of carb-cleaning, there's plenty of passages that flow petrol before and after jets that needs attention as well. These nifty little suckers really help! |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
HELP! idle adjustment screw came out! | str8t six | 2008 - 2012 Ninja 250R Tech Talk | 5 | March 21st, 2012 10:30 AM |
Stripped fuel bowl screw now what? | Slono | 2008 - 2012 Ninja 250R Tech Talk | 10 | March 19th, 2012 12:38 PM |
idle screw adjustment | headshrink | 2008 - 2012 Ninja 250R Tech Talk | 6 | February 5th, 2012 08:46 PM |
Idle Mixture adjustment screw Q | indr | 2008 - 2012 Ninja 250R Tech Talk | 1 | December 2nd, 2010 09:36 PM |
Valve Adjustment-Really Tight adjustment screw? | mikesova | 1986 - 2007 Ninja 250R Tech Talk | 5 | May 2nd, 2010 04:57 AM |
|
|