ninjette.org

Go Back   ninjette.org > 2008 - 2012 Ninja 250R > 2008 - 2012 Ninja 250R Tech Talk

Notices

Reply
 
Thread Tools
Old December 4th, 2018, 11:30 AM   #41
Fern2400
ninjette.org newbie
 
Name: Fernando
Location: Nova Scotia
Join Date: Sep 2018

Motorcycle(s): Cbr f4i and ninja 250

Posts: 3
a few shot from the ground one vs the untouch one yet. If you look inside, you’ll see 4?(teeth) towards the inside of the tube. Didn’t see those in the above thread so I’m confused about it. The bushing still rotate but don’t come out?? I ties with PVC on the concrete and the teeth broke the tip of the PVC.



https://i.imgur.com/DOus5Wn.jpg

https://i.imgur.com/sAQQ3yr.jpg
Fern2400 is offline   Reply With Quote




Old December 4th, 2018, 10:30 PM   #42
dino74
ninjette.org certified postwhore
 
dino74's Avatar
 
Name: dino
Location: Oceanside, Ca
Join Date: Nov 2010

Motorcycle(s): '09 250 Street, '09 250 Race, '13 300 Race

Posts: A lot.
Don't worry about the four teeth. I used a ~1" wooden dowel($4 at hw store) to punch out the bushing after grinding. Check you ID of the tube and buy the largest dowel that will fit.
__________________________________________________
CVMA #55

Last futzed with by dino74; December 4th, 2018 at 11:54 PM.
dino74 is offline   Reply With Quote


Old December 5th, 2018, 03:43 AM   #43
Fern2400
ninjette.org newbie
 
Name: Fernando
Location: Nova Scotia
Join Date: Sep 2018

Motorcycle(s): Cbr f4i and ninja 250

Posts: 3
Thanks Dino, I got it! I use a steel bar that I had laying around. I wrapped it in tape to protect the tube. Really good write up! Made the job easy.
Fern2400 is offline   Reply With Quote


Old December 5th, 2018, 07:42 AM   #44
dino74
ninjette.org certified postwhore
 
dino74's Avatar
 
Name: dino
Location: Oceanside, Ca
Join Date: Nov 2010

Motorcycle(s): '09 250 Street, '09 250 Race, '13 300 Race

Posts: A lot.
Quote:
Originally Posted by Fern2400 View Post
Thanks Dino, I got it! I use a steel bar that I had laying around. I wrapped it in tape to protect the tube. Really good write up! Made the job easy.
One tidbit I learned since the write up. Before you tighten the cartridge to the lower, reassemble the upper and lower first. Put the cartridge in and hand tighten the bolt. To help center it, put the cap on without the springs.
__________________________________________________
CVMA #55
dino74 is offline   Reply With Quote


Reply




Similar Threads
Thread Thread Starter Forum Replies Last Post
[roadracingworld.com] - Video: Installing Öhlins 30mm Fork Cartridges On A Honda CBR1 Ninjette Newsbot Motorcycling News 0 February 8th, 2015 09:50 AM
TWF Racing Cartridges. shane liberty Ninjettes At Speed 13 June 3rd, 2014 03:12 PM
- - - WTB Rear Shock & Cartridges 08-12 - - - Triple R Items Wanted 2 May 19th, 2014 08:59 AM
WTB andreani fork cartridge kit chugs Items Wanted 0 February 15th, 2014 10:47 PM
Installing New AP Exhaust xaple 2008 - 2012 Ninja 250R Tech Talk 9 September 29th, 2012 08:23 AM


Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


Motorcycle Safety Foundation

All times are GMT -7. The time now is 01:54 AM.


remote server monitor
Powered by vBulletin®
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
User Alert System provided by Advanced User Tagging (Lite) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Except where otherwise noted, all site contents are © Copyright 2016 ninjette.org, All rights reserved.