ninjette.org

Go Back   ninjette.org > 2008 - 2012 Ninja 250R > 2008 - 2012 Ninja 250R Tech Talk

Notices

Reply
 
Thread Tools
Old July 16th, 2022, 05:04 PM   #1
Fatherof2
ninjette.org member
 
Name: David
Location: Massachusetts
Join Date: Jun 2022

Motorcycle(s): 2017 Triumph Trophy, 2001 Honda Valkyrie, 2007 Ninja 250, 2017 Yamaha 250X, 2018 YZ125

Posts: 18
Slight hanging idle question.

Hi Gang,

I picked up a 2007 250 with less than 3K miles. It had been sitting for a long time.

I rebuilt the carbs, and the bike starts easily. It will start without choke on these warm days we have been having.

When the bike is idling at 1500 rpms, and I blip it up to 3,000 or so, the idle hangs up there a bit and kind of slowly drops back down to 1,500. It feels like a delayed reaction as it returns to 1500ish.

If I rev it up to 4 or 5K and let it drop back to 3Kish, it seems to come back down in a more normal fashion.

Bike screams nicely when up in the higher rev range. Seems to be running fine when I do that.

Any input is appreciated.

Thanks All!
Fatherof2 is offline   Reply With Quote




Old July 16th, 2022, 05:37 PM   #2
DannoXYZ
ninjette.org certified postwhore
 
Name: AKA JacRyann
Location: Mesa, AZ
Join Date: Dec 2011

Motorcycle(s): CB125T CBR250R-MC19 CBR250RR-MC22 NSR350R-MC21 VF500F CBR600RR SFV650 VFR750F R1M ST1300PA Valkyrie-F6C

Posts: A lot.
MOTY - 2018, MOTM - Nov '17
1. Did you disassemble down to every last nut, bolt and individual component? If it can be further disassembled, do it.


2. Poked out all lateral bleed holes in carb-venturi, emulsion-tubes, pilot-jets?


3. scrubbed out all secret hidden passages with PEA-based fuel-system cleaner with brushes?
http://n4mwd.blogspot.com/2013/10/se...-passages.html

4. ultrasonic soak, micro soda-blast everything?

5. replaced all rubbers: fuel-rail O-rings, float valves, mixture-screw O-rings, float-bowl seals?

6. set float-height with final wet-test to verify?

7. sync carbs after installation?


Do search on here for "clean carbs ducatiman" for threads with how-tos and photos.
DannoXYZ is offline   Reply With Quote


1 out of 1 members found this post helpful.
Old July 18th, 2022, 07:25 AM   #3
jkv45
Rev Limiter
 
jkv45's Avatar
 
Name: Jay
Location: WI
Join Date: Jul 2013

Motorcycle(s): '06 SV650n, '00 Derbi GPR, '64 CA77 Dream 305, '70 CL450 Scrambler, numerous dirt bikes

Posts: A lot.
MOTM - Jun '18, Oct '16
Danno pretty much has it covered. Doing carbs right isn't quick or easy.

Many times, hanging RPMs means a vacuum leak -but it can also be just a lean condition due to improper adjustments or partially plugged carb circuits.

Did you remove the idle mixture caps, idle mixture screws, clean the passages, and check that the o-rings are in good condition?

Most of the time, when everything else is correct, setting the idle mixture screws to 2-turns out initially gives you a good place to start.

After it's fully warm, I will adjust the screws to get the highest RPMs at idle, go about 1/8-turn out (richer), then set the idle speed to 1200 or so.

Syncing the carbs is also a good idea before fine-tuning the mixture screws.
jkv45 is offline   Reply With Quote


Reply




Similar Threads
Thread Thread Starter Forum Replies Last Post
Slight idle issue NinjaNelly 2008 - 2012 Ninja 250R Tech Talk 8 May 9th, 2020 01:55 AM
Hanging idle and dies with throttle? gitter 2008 - 2012 Ninja 250R Tech Talk 30 November 9th, 2017 08:32 AM
Question about idle mixture screw and low idle flux daverdfw 2008 - 2012 Ninja 250R Tech Talk 3 June 2nd, 2016 10:36 PM
Idle Question THE BIG SITT 2008 - 2012 Ninja 250R Tech Talk 22 October 29th, 2011 07:15 AM
Hanging Idle ak_907_ak 2008 - 2012 Ninja 250R Tech Talk 33 June 14th, 2009 08:31 PM


Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


Motorcycle Safety Foundation

All times are GMT -7. The time now is 04:28 PM.


Website uptime monitoring Host-tracker.com
Powered by vBulletin®
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
User Alert System provided by Advanced User Tagging (Lite) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
Except where otherwise noted, all site contents are © Copyright 2022 ninjette.org, All rights reserved.