![]() |
![]() |
#1 |
ninjette.org member
Name: Matt
Location: Middle GA
Join Date: May 2010 Motorcycle(s): 2003 Ninja 250 Posts: 184
|
Cold Start issue
I have an 03 with 8500 miles, out side its been between 60-90f. I have a hard time getting it started while it is cold... After the motor gets warm it will recrank fine. I have, Changed oil (mobile clean 5000 10-40),Cleaned air filter, ran seafoam, Replaced fuel filter, replaced plugs, Adjusted the air/fuel mix to what seems to be near correct... fresh gas, Cleaned carbs,... tried boosting from a good car battery just to check cranking power. Throttle nor choke seem to make much of a difference.... Even after i get it to crank it still wants to die out until warm... Idle knob is adjusted to approx 1700 rpm while warm... Thanks for all your time
|
![]() |
![]() |
![]() |
#2 |
Join Date: Nov 2008 Posts: Too much.
|
are you using full choke?
|
![]() |
![]() |
![]() |
#3 |
ninjette.org member
Name: Matt
Location: Middle GA
Join Date: May 2010 Motorcycle(s): 2003 Ninja 250 Posts: 184
|
tried none full half and every where in between... it was working fine... then seemingly i got a bad batch of gas (my thought of this time) but that gas is gone, fresh in...
|
![]() |
![]() |
![]() |
#4 |
Join Date: Nov 2008 Posts: Too much.
|
My thoughts are that the pilot jet is clogged, but the bike should run if the choke is used on a cold start. is the choke cable adjusted properly at the carbs?
try seafoam again by pouring some directly into the fuel hose so it can be drawn full strength into the carbs. let it sit overnight with that high concentration in the bowls to give the seafoam a chance to break down the goo and try starting it again in the morning. |
![]() |
![]() |
![]() |
#5 |
ninjette.org certified postwhore
Name: Alex
Location: Belfast, ME
Join Date: Jul 2008 Motorcycle(s): 2010 Honda NT-700-V, formerly, Green 2008 Ninja 250R Posts: A lot.
|
Kelly, Remember the good old days when we did not have to worry about "goo" in our gas. Boy, have they screwed up fuel these days!
|
![]() |
![]() |
![]() |
#6 |
ninjette.org member
Name: Matt
Location: Middle GA
Join Date: May 2010 Motorcycle(s): 2003 Ninja 250 Posts: 184
|
I pulled the carbs soaked everything that could be in carb cleaner for a few hours...
|
![]() |
![]() |
![]() |
#7 |
Join Date: Nov 2008 Posts: Too much.
|
are you saying you just did this a few minutes ago or before the problem started?
when you soaked them, did you remove all the jets and did you blow out the passages after the soak? |
![]() |
![]() |
![]() |
#8 | |
Live Life
Name: Don
Location: Lincoln, NE
Join Date: Nov 2008 Motorcycle(s): 2009 Green SE Ninja 250 Posts: A lot.
|
Quote:
![]()
__________________________________________________
- ATGATT - Scorpion EX700 Hi-Vis Helmet, First Gear MeshTek 3.0 Jacket, TourMaster Transition 2 Jacket and Flex Pants, Sidi Doha boots |
|
![]() |
![]() |
![]() |
#9 |
ninjette.org member
Name: Matt
Location: Middle GA
Join Date: May 2010 Motorcycle(s): 2003 Ninja 250 Posts: 184
|
i did it after the problem started... pulled and cleaned twice.... problem has been going on for like 4 weeks now
|
![]() |
![]() |
![]() |
#10 |
ninjette.org member
Name: Matt
Location: Middle GA
Join Date: May 2010 Motorcycle(s): 2003 Ninja 250 Posts: 184
|
I'm Probably going to pull carbs again and soak with seafoam and carb cleaner and see... any other suggestions to look into while i have carbs off?
|
![]() |
![]() |
![]() |
#11 |
Join Date: Nov 2008 Posts: Too much.
|
remove and clean the jets and passage ways.
unless you do this, your not really cleaning a carb. did you do this previously? |
![]() |
![]() |
![]() |
#12 |
ninjette.org member
Name: Matt
Location: Middle GA
Join Date: May 2010 Motorcycle(s): 2003 Ninja 250 Posts: 184
|
yes
![]() |
![]() |
![]() |
![]() |
#13 |
Join Date: Nov 2008 Posts: Too much.
|
did you look down the middle of the jets to make sure they were cleaned out? you should be able to see a nice clear hole down the middle.
did you blow out the passage ways w/ compressed air? were you able to feel air passing through to the little exit holes in the carb throat area when you blew from the removed pilot jet passage?? http://faq.ninja250.org/wiki/How_do_...n_the_carbs%3F |
![]() |
![]() |
![]() |
#14 | |
ninjette.org member
Name: Matt
Location: Middle GA
Join Date: May 2010 Motorcycle(s): 2003 Ninja 250 Posts: 184
|
Quote:
|
|
![]() |
![]() |
![]() |
#15 |
ninjette.org member
Name: Matt
Location: Middle GA
Join Date: May 2010 Motorcycle(s): 2003 Ninja 250 Posts: 184
|
it seems to want to hessitate starting but it never will regardless of choke or throttle position.. checked choke seems to be actuating everything..
|
![]() |
![]() |
![]() |
#16 |
Join Date: Nov 2008 Posts: Too much.
|
|
![]() |
![]() |
![]() |
#17 |
ninjette.org member
Name: Matt
Location: Middle GA
Join Date: May 2010 Motorcycle(s): 2003 Ninja 250 Posts: 184
|
it means the last owner messed with it but its back to 2.5
|
![]() |
![]() |
![]() |
#18 |
ninjette.org member
Name: Matt
Location: Middle GA
Join Date: May 2010 Motorcycle(s): 2003 Ninja 250 Posts: 184
|
Just cleaned the gas tank completely and filled up with new gas...would valve adjustment cause a situation that would not start but hesitate a little like it wants to?
|
![]() |
![]() |
![]() |
#19 |
ninjette.org member
Name: Matt
Location: Middle GA
Join Date: May 2010 Motorcycle(s): 2003 Ninja 250 Posts: 184
|
AND FIXED!!!!.. turns out it was the valve adjustment... one intake was way loose.... and the other three really tight... *shrug* how that happened... but it starts right up now
![]() ![]() |
![]() |
![]() |
![]() |
#20 |
Join Date: Nov 2008 Posts: Too much.
|
Way to go, Matt!
![]() |
![]() |
![]() |
![]() |
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Cold Weather Fuel Injection Issue | akima | 2008 - 2012 Ninja 250R Tech Talk | 38 | October 23rd, 2012 04:39 AM |
Can you start when it's cold? | blink | General Motorcycling Discussion | 18 | April 14th, 2012 01:01 PM |
Cold Start Concerns | hoodadooda | 2008 - 2012 Ninja 250R Tech Talk | 7 | September 11th, 2011 09:50 PM |
Help with cold start (without choke) | d16soda | 1986 - 2007 Ninja 250R Tech Talk | 4 | August 31st, 2011 01:17 PM |
Re shimmed...worse cold start? | M-Oorb | 2008 - 2012 Ninja 250R Tech Talk | 67 | August 1st, 2009 04:56 PM |
|
|