July 19th, 2020, 06:42 PM | #1 |
ninjette.org member
Name: Arthur
Location: Sammamish , WA
Join Date: Jun 2020 Motorcycle(s): 2008 Ninja EX250J; 2005 CBR1000RR Posts: 108
|
Missing a bolt hole?
REF: https://www.partzilla.com/catalog/ka...cowling-lowers
Looking at bolt (part #: 92151) at the bottom of the side cowling, it looks like it is screwed into a screw-hole on the frame? Mine has broken off. Any solution for this? |
|
July 19th, 2020, 07:53 PM | #2 |
ninjette.org certified postwhore
Name: AKA JacRyann
Location: Mesa, AZ
Join Date: Dec 2011 Motorcycle(s): CB125T CBR250R-MC19 CBR250RR-MC22 NSR350R-MC21 VF500F CBR600RR SFV650 VFR750F R1M ST1300PA Valkyrie-F6C Posts: A lot.
MOTY - 2018, MOTM - Nov '17
|
Look closely at hole in frame with bright torche. Can you see through hole? Or is broken bolt stuck in there?
If there's enough sticking out, you can grab it with vice-grips and twist it out? Then get any 6x1mm bolt to replace. I like to add large washer between bolt and bodywork to press firmly without cutting through bodywork. |
|
July 19th, 2020, 09:58 PM | #3 |
ninjette.org member
Name: Arthur
Location: Sammamish , WA
Join Date: Jun 2020 Motorcycle(s): 2008 Ninja EX250J; 2005 CBR1000RR Posts: 108
|
Oh, I was not clear.
I meant to say that the female of where the bolt was supposed to screw in broke off from the frame, I think. Based on the diagram, it looks as if the large bolt at the bottom is bolted to the frame. |
|
July 20th, 2020, 01:35 AM | #4 |
ninjette.org certified postwhore
Name: AKA JacRyann
Location: Mesa, AZ
Join Date: Dec 2011 Motorcycle(s): CB125T CBR250R-MC19 CBR250RR-MC22 NSR350R-MC21 VF500F CBR600RR SFV650 VFR750F R1M ST1300PA Valkyrie-F6C Posts: A lot.
MOTY - 2018, MOTM - Nov '17
|
Simple enough to braze or weld that bracket back on.
|
|
July 20th, 2020, 06:53 AM | #5 |
ninjette.org member
Name: Arthur
Location: Sammamish , WA
Join Date: Jun 2020 Motorcycle(s): 2008 Ninja EX250J; 2005 CBR1000RR Posts: 108
|
Thanks, I'll see what I can do.
|
|
July 21st, 2020, 10:32 AM | #6 |
ninjette.org certified postwhore
Name: AKA JacRyann
Location: Mesa, AZ
Join Date: Dec 2011 Motorcycle(s): CB125T CBR250R-MC19 CBR250RR-MC22 NSR350R-MC21 VF500F CBR600RR SFV650 VFR750F R1M ST1300PA Valkyrie-F6C Posts: A lot.
MOTY - 2018, MOTM - Nov '17
|
What I would do is get angle bracket. Weld nut to it. Then weld bracket to frame.
Home Depot - angle bracket As with anything else, measure twice, cut once. |
|
July 21st, 2020, 10:39 AM | #7 |
ninjette.org member
Name: Arthur
Location: Sammamish , WA
Join Date: Jun 2020 Motorcycle(s): 2008 Ninja EX250J; 2005 CBR1000RR Posts: 108
|
Thanks, Danno./
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
What size bolt hole is this? | Hero Danny | 2013 - 2017 Ninja 300 Tech Talk | 4 | April 29th, 2015 10:01 AM |
Rotor bolt hole spacing and pattern. | Rassie | 2013 - 2017 Ninja 300 Tech Talk | 4 | August 23rd, 2014 03:33 PM |
Missing essential bolt! Need help! | Floki | 2008 - 2012 Ninja 250R Tech Talk | 4 | October 6th, 2013 03:08 PM |
fairing bolt missing | kittyslasher | 2008 - 2012 Ninja 250R Tech Talk | 3 | July 30th, 2013 04:44 PM |
Help with missing bolt | dk58 | 2008 - 2012 Ninja 250R Tech Talk | 22 | May 11th, 2011 07:07 PM |
|
|