June 5th, 2009, 10:08 AM | #41 |
Giggity Giggity
Name: Ryam
Location: San Diego
Join Date: Feb 2009 Motorcycle(s): 08 ninja 250R aka Hiryu Posts: 481
|
The mod affects the entire power band of the bike, increased fuel to balance out mods that may have increased air flow like exaust or air filters etc. I think it may make a very insignificant decrease in mileage(I get like maybe 5 miles less a tank). The increase in performance is significant...
__________________________________________________
Facebook DY Fender chop, Danmoto CB slip-on w/baffle, Airbox removed, Kleen-air removed, shimmed needles, Mikuni #117.5 Main jets, K&N RU-1822 air filter pods |
|
June 5th, 2009, 10:47 AM | #42 |
Join Date: Nov 2008 Posts: Too much.
|
|
|
June 5th, 2009, 06:57 PM | #43 |
I'm lovin' it.
Name: Mike
Location: Melb, Australia
Join Date: Feb 2009 Motorcycle(s): '09 Black 250R Posts: A lot.
|
It probably will drop a tad because the bike would be so much better to ride, tempting you to twist the throttle a little more.
__________________________________________________
Son: When I grow up I want to ride a motorbike. Father: You can't do both son. |
|
June 15th, 2009, 01:02 AM | #44 |
Ninja World YAY
Name: Vik
Location: Bay Area
Join Date: Feb 2009 Motorcycle(s): Ninja 250 Posts: 102
|
i really want to shim the needles but i dont think i will be able to do it myself i am not sure how much the shop will charge me for that but i am assuming it will be around $100 wish there was someone from the forums who lived close by to do the shimming for me
|
|
June 15th, 2009, 01:06 AM | #45 |
Join Date: Nov 2008 Posts: Too much.
|
Start a new thread asking for help in the bay area and see if there is someone in your area responds.
|
|
August 6th, 2009, 12:07 AM | #46 |
ninjette.org member
Name: Shannon
Location: Georgia
Join Date: Aug 2009 Motorcycle(s): 2009 Ninja 250r Posts: 54
|
Ok, I definitely need this mod....where are you guys finding these washers? Where can I gt them?
Thanks! |
|
August 6th, 2009, 01:30 AM | #47 |
Join Date: Nov 2008 Posts: Too much.
|
|
|
November 5th, 2011, 11:39 AM | #48 |
ninjette.org member
Name: Javi
Location: Salinas, CA
Join Date: Nov 2011 Motorcycle(s): 2012 Ninja 250r Lime Green :) Posts: 25
|
I just want to make sure I get this right. For a complete stock 2012 250R 1 washer, what if I remove the snorkel? Would that be 2 washers? Thanks
|
|
November 5th, 2011, 03:45 PM | #49 |
ninjette.org member
Name: Christine
Location: pittsburgh, pa
Join Date: Jan 2009 Motorcycle(s): 2011 black ninja 250r Posts: 67
|
I DEfinately need this mod done. Will a dealer do this for me or is it done as a DIY only. And what exactley does this do that makes it run bettter? I have the bogging starts no matter how warmed up I get it and it is a concern especially at red lights. Thanks for the info.
|
|
November 15th, 2011, 06:26 PM | #50 | |
ninjette.org certified postwhore
Name: Paul
Location: Roanoke, VA
Join Date: Jun 2009 Motorcycle(s): 2008 Candy Plasma Blue 250R Posts: A lot.
|
Quote:
Usually a dealer will suggest/direct you to buy a jet kit (usually $90), in addition to the labor cost for installing it and dialing it in. The jet kit would have adjustable needles in it that would allow finer tweaking than using stock needles and washers, as well as parts for altering other parts of the fuel flow regulation system. The washers are almost exclusively a DIY, unless you've got a very good, flexible shop. Essentially adding washers under the needles adds more fuel (richens the mix) in the midrange where our bikes are notoriously lean from the factory. A jet kit would also include a range of main jets to adjust the top end fuel flow. If you're sticking with a stock intake-exhaust setup, washers will likely be about all you need, maybe a little fiddling with the pilot jets (control gas flow for very low end/idle, but can affect flow across the range), which is fairly easy if you're patient and have a few tools on hand.
__________________________________________________
Proud member of the Blue Army |
|
|
November 15th, 2011, 08:05 PM | #51 |
ninjette.org member
Name: Christine
Location: pittsburgh, pa
Join Date: Jan 2009 Motorcycle(s): 2011 black ninja 250r Posts: 67
|
Thank You Momaru. I probably will buy a kit and have the dealer do the work. The dealer quoted me 3 hrs labor and its a lot too involved for me . Thanks for explaining it.
|
|
November 15th, 2011, 08:11 PM | #52 |
ninjette.org certified postwhore
Name: .
Location: .
Join Date: Feb 2011 Motorcycle(s): . Posts: Too much.
MOTM - Feb '13, Feb '14
|
3 hrs labor ??? if it's a little too involved for you, find a friend who is mechanically inclined and experienced working on cars/bikes and read through some DIY's and take a crack at it. 2 heads is better than one. If you can't get it right, set it all back the way you found it and then go to the dealer to have them jet for you.
3 hrs labor is awfully expensive for something that just requires patience and time |
|
November 15th, 2011, 09:25 PM | #53 |
ninjette.org certified postwhore
Name: Paul
Location: Roanoke, VA
Join Date: Jun 2009 Motorcycle(s): 2008 Candy Plasma Blue 250R Posts: A lot.
|
May take a few hours to get things dialed in. The 'two washers' suggestion is just that; doesn't work for everyone. But I agree that 3 hours is a little much. An experienced mechanic (or owner) can get the bike stripped/dressed in 15 mins or less. A few more for the tank and you're there. Maybe two hours, if they need to strip/dress the bike and have to make a few separate runs to pick good settings.
That said, proper tuning can be an all-day job, but you very very rarely get that with just a straight up kit install.
__________________________________________________
Proud member of the Blue Army |
|
November 16th, 2011, 08:07 PM | #54 |
ninjette.org member
Name: Christine
Location: pittsburgh, pa
Join Date: Jan 2009 Motorcycle(s): 2011 black ninja 250r Posts: 67
|
Thanks guys I will check into some more quotes and look into recruiting a mechanical inclined helper as well
|
|
November 17th, 2011, 11:53 AM | #55 |
ninjette.org guru
Name: Charlie
Location: Wylie, TX
Join Date: Nov 2011 Motorcycle(s): 2007 Ninja 650R Posts: 317
|
I think I want to give this a try..just wanted to make sure this is really as simple as the instructions said. Remove the cover, pull the needle out, slide the washer(s) onto the needle, and put the needle back in? Is it really that easy, other than making sure the boot stays seated & the spring is aligned during re-assembly?
|
|
November 17th, 2011, 05:56 PM | #56 | |
ninjette.org certified postwhore
Name: Paul
Location: Roanoke, VA
Join Date: Jun 2009 Motorcycle(s): 2008 Candy Plasma Blue 250R Posts: A lot.
|
Quote:
Few other warnings/suggestions though: The carb caps are under spring pressure, so they may pop up at ya. Make VERY sure you don't poke a hole in the diaphragm (expensive to replace and a pain to repair) and that you get the needles back into the correct carb side. I'm not 100% sure about pre-gens, but the new gens have two different OEM needles (one per carb/cylinder) and it matters which side is which. The washers will sit "under" the needle, so they will fall off into the diaphragm (what you called the boot) if you don't hold onto them while re-loading the needles. And finally, pay attention to where the vacuum lines go/how they're routed BEFORE you take things apart. You might even label them with some tape if you're not sure... Most of the hoses are pretty easy, but there's a few that are easy to mix up.
__________________________________________________
Proud member of the Blue Army |
|
|
November 18th, 2011, 09:02 AM | #57 |
ninjette.org guru
Name: Charlie
Location: Wylie, TX
Join Date: Nov 2011 Motorcycle(s): 2007 Ninja 650R Posts: 317
|
I tried this mod last night. No go. Everything came apart & went back together perfectly. The bike fired right up and ran on choke exactly how it normally does. Reved it up a few times, seemed to be fine. Kicked it into first, and it choked and died as I attempted to accelerate out into the street. Fired back up & attempted to ride. HUGE dead area between 2000 + 6000 RPMS, then, like an engine with big turbo lag, it would pick up and haul ass after 6000.
The O.D. of these washers was a couple mm smaller than 3/8, so I thought they'd work. When I took it all apart again, the washers had gotten lodged in the plastic retainers on the bottom of the springs, which caused the needles to stick in the 'up' position. Naturally, this causes very bad running <6000 rpm. Should the needle be sliding up and down through the washer, or should the washer be traveling up with the needle? Whatever the case, the washers traveled upward, got stuck and then the needles couldn't drop back down. So...should I be using smaller washers so they can't get stuck in the retainers, or larger ones so the retainers sit on top of the washers? Removed the washers & re-assembled. It runs exactly like it did before, so I don't think there's anything wrong anywhere. |
|
November 18th, 2011, 11:11 AM | #58 |
ninjette.org guru
Name: Charlie
Location: Wylie, TX
Join Date: Nov 2011 Motorcycle(s): 2007 Ninja 650R Posts: 317
|
Update: Dug into it again and added a tiny neoprene washer to each needle. Fits snugly around the top and up against the head of the needle. A hair thicker than the stainless steel washers that didn't work.
I don't notice a huge difference, but there seems to be a little better response off idle. |
|
November 18th, 2011, 05:15 PM | #59 |
ninjette.org certified postwhore
Name: Paul
Location: Roanoke, VA
Join Date: Jun 2009 Motorcycle(s): 2008 Candy Plasma Blue 250R Posts: A lot.
|
That range you're having problems (2k-6k) is largely controlled by the pilot screws, I'd look through some of the other tuning DIYs (this one by Vex is the main one for pilot jets here, and this is the one for shimming the carb needles, by Kkim). Frankly I'm too braindead from work to make a suggestion about which way you want to adjust the pilot screws, but I *think* you may want to push them in a smidge, as raising the needles has introduced a lot more gas in the midrange, possibly richening the mix overmuch. Definitely take a look through the tuning DIYs, or go to thedark side & read thru the intake FAQs @ ninja250.org
Regarding the washers; the needle, washers, and retainer all move together as the boot moves up and down with the diaphragm. Doesn't matter overmuch that the washers were a bit too snug in the retainer, so long as the retainer fit snugly on the needle top to keep it from coming up on its own (the spring & retainer are there to keep it seated in the plastic part of the diaphragm slide (hard plastic part).
__________________________________________________
Proud member of the Blue Army |
|
November 19th, 2011, 08:48 AM | #60 |
ninjette.org guru
Name: Charlie
Location: Wylie, TX
Join Date: Nov 2011 Motorcycle(s): 2007 Ninja 650R Posts: 317
|
The 2K - 6K problem cleared up when I replaced the #4 washers with some tiny neoprene ones that fit snugly under the needle heads. I think what happened was the steel washers lodged in the retainers at an angle, trapping the needle where the head wasn't seated at the top of the retainer like it should be. When I pulled the springs out, the needles and washers came out with them. Everything's solved now...running great. My mixture screws are still sealed, so I won't be messing with those unless I experience a running problem. I really don't want to take the carbs out.
|
|
November 19th, 2011, 11:09 AM | #61 |
ninjette.org certified postwhore
Name: Paul
Location: Roanoke, VA
Join Date: Jun 2009 Motorcycle(s): 2008 Candy Plasma Blue 250R Posts: A lot.
|
Huzzah! Glad you got things figured out. I'd assumed the washers were sitting flat, & allowing your needle to behave normally, glad you tracked it down!
Some materials don't do so well in environments rich in gasoline & fumes, might want to check on them in a weeks to see how that rubber's holding up. I agree re: messin' with pilots/other tuning; if it ain't broke, don't fix it :P
__________________________________________________
Proud member of the Blue Army |
|
November 21st, 2011, 08:08 AM | #62 |
ninjette.org certified postwhore
Name: .
Location: .
Join Date: Feb 2011 Motorcycle(s): . Posts: Too much.
MOTM - Feb '13, Feb '14
|
Good idea to check the neoprene ones just in case
if the rubber ones give you any trouble, the metal washers that work are SAE #4 washers (i believe). they're barely larger in diameter than the head of the needle and don't have any issues hanging up on anything. |
|
November 21st, 2011, 08:32 AM | #63 |
ninjette.org guru
Name: Charlie
Location: Wylie, TX
Join Date: Nov 2011 Motorcycle(s): 2007 Ninja 650R Posts: 317
|
That kinda makes me wonder what I bought. The package said #4, so I went with it. Hmm....
I'm hoping the washers I used will be ok, since they are actually un-used parts I bought for my '94 Ninja carb a few years ago. (92055 RING-O,PILOT ADJUST). They sit on top of the pilot air screws, but since they fit the jet needle perfectly, I went with them. |
|
November 21st, 2011, 06:13 PM | #64 |
ninjette.org member
Name: jOE
Location: Jacksonville
Join Date: Nov 2011 Motorcycle(s): none yet (getting a 250R) Posts: 68
|
-- I'm about to put two or three washers in since it's much cheaper and easier than rejecting with new needles. Since it'll have a new exhaust, I may then pull the snorkel out and see how it likes that, too. I'm not looking to race...I just want the better sound and looks and weight of exhaust, but don't want it to run too lean or rich or hurt my engine.
I'll be reading up on how to determine whether it's too rich or lean. How much do dealerships charge to rejet (after you pay for the $90 dynojet kit)? |
|
November 21st, 2011, 06:26 PM | #65 | |
ninjette.org certified postwhore
Name: .
Location: .
Join Date: Feb 2011 Motorcycle(s): . Posts: Too much.
MOTM - Feb '13, Feb '14
|
Quote:
If you want to rejet, learn how to diagnose carbs, and then do it yourself. Then get it dyno'd to get the mix perfect if you want the bike running perfectly. If you try a million different combinations of jets and washers and still can't seem to get it right, then put it all back the way you found it, and take it to the dealership to have them do it for you |
|
|
March 21st, 2012, 10:17 AM | #66 |
ninjette.org member
Name: Zander the Expander
Location: Houston, Texas
Join Date: Nov 2011 Motorcycle(s): 2010 Kawasaki 250 (Track scooter) 2012 Triumph Daytona 675 Posts: 153
|
what size washers do you need?
|
|
March 21st, 2012, 02:12 PM | #67 |
ninjette.org certified postwhore
Name: .
Location: .
Join Date: Feb 2011 Motorcycle(s): . Posts: Too much.
MOTM - Feb '13, Feb '14
|
SAE #4. Basically as small as you can find.
|
|
April 20th, 2012, 11:32 AM | #68 |
ninjette.org member
Name: Lawrence
Location: Jersey City, NJ
Join Date: Mar 2012 Motorcycle(s): '08 Ninja 250R Posts: 14
|
I'm pretty sure my bike (stock '08) has the usual symptoms of a bike that should be shimmed. It has a hard time starting unless it's on full choke, rough idle initially, takes around 10 minutes to warm up, etc. However, I do smell a pretty strong gas smell from the exhaust. This is usually a sign of the bike running too rich, correct?
|
|
June 23rd, 2012, 07:01 PM | #69 |
ninjette.org guru
Name: Toua
Location: Long Beach
Join Date: May 2012 Motorcycle(s): Ninja 250 and Gsx-R 750 k8 (out of commission) Posts: 482
|
So shimmed my carbs today and runs like crap around 7k rpm it's struggles and decreases in power up until 10,000 rpm... any suggestions?
|
|
November 13th, 2012, 01:40 PM | #70 |
ninjette.org newbie
Name: Tony
Location: Norfolk, VA
Join Date: Nov 2012 Motorcycle(s): Ninja 250 Posts: 5
|
Will this MOD void my factory warranty?
|
|
November 22nd, 2012, 08:38 PM | #71 |
ninjette.org member
Name: max
Location: bali
Join Date: Nov 2012 Motorcycle(s): ninja 250 Posts: 60
|
Hi all, I am a new member here. I just want to ask my bike don't have any problem hesitate or bog with stock muffler or slip on muffler from stop to take off. I try to shim 1 washer each needle but my bike is not rev as stock jetting, then I try to add 1 washer again, but at 7k rpm, they like hesitate then rev to 10k. So my question here, should I shim my bike?
thanks. ps : mixuture set L (2 1/2), R (1 3/4). PJ 38 MJ 98 |
|
November 28th, 2012, 10:42 PM | #72 |
Razor's Edge
Name: Richard
Location: El Paso, San Antonio, Ennis...Texas
Join Date: Nov 2012 Motorcycle(s): 2007 Sportster XL1200C Posts: 196
|
2012 with 1800 miles. Bought new with 1 mile on it.
Here in El Paso, TX the temps are usually in the 30-40s in the morning, warming up to the 60-70s in the afternoon. I am at about 3800ft and in a dry/dusty environment. In the morning, the bike has a tendancy to bog for a split second, then take off into the higher rpms. The bike tends to seem more powerful at high rpms while cold. Once the bike is at operating temperature, the low-mid power smooths out and top end seems to tone down. From my limited knowledge, I am assuming that I should at least start with one washer. Maybe later go one size larger on the main. Am I correct on my assumption? My bike is completely stock, snorkel and all. |
|
December 29th, 2012, 10:40 PM | #73 |
Razor's Edge
Name: Richard
Location: El Paso, San Antonio, Ennis...Texas
Join Date: Nov 2012 Motorcycle(s): 2007 Sportster XL1200C Posts: 196
|
Completed this modification. Went with (2) #4 washers for each. I have noticed something different though. Now with the shimming, I notice easier starting, but also noticed that when I let off the choke to fast, it dies. This mostly happens when it's cold. The temps are in the 20s-30s in El Paso, and slightly higher in S.A. and the Dallas area. I didn't notice it so much in S.A. or the Dallas area though.
Could the shimming and decreasing cold temperatures cause this to happen? completely stock, I did not notice any sudden stalling when I reduced choke. After modifying, I have to slightly move reduce choke otherwise I will see spikes and sudden drops in idle as well as stalling. Other members on this forum said it could be a result of a cold engine. I will go ahead and check/adjust the carb sync. Once the engine is warm, I don't have any issues. It runs great. I do get a small fuel smell from the exhaust. Could this be a rich condition causing the erratic up/down idling and stalling while cold? I will remove one washer from each side and see where I end up after that. I will keep you all posted. |
|
December 29th, 2012, 10:57 PM | #74 |
ninjette.org guru
Name: Richie
Location: Arkansas
Join Date: Apr 2011 Motorcycle(s): 2022 Honda CRF300L Rally, 2015 Ninja ZX6R 636, 2014 Ninja 1000, 2013 Ninja 300 (sold), 2011 Ninja 250R (sold) Posts: 479
|
How soon are you turning off the choke? As it gets colder, the warm up time increases, as does the time you should leave the choke applied. As the bike warms, you should decrease the amount of choke a bit at a time until completely off. Not all at once.
|
|
December 30th, 2012, 11:09 AM | #75 |
Razor's Edge
Name: Richard
Location: El Paso, San Antonio, Ennis...Texas
Join Date: Nov 2012 Motorcycle(s): 2007 Sportster XL1200C Posts: 196
|
It will do the same if I do it after 5 minutes. I will record it and post the video.
|
|
December 31st, 2012, 12:42 PM | #76 |
Daily Jap rider
Name: Lance
Location: La Porte
Join Date: Dec 2012 Motorcycle(s): 2012 Ninja 250r Posts: A lot.
|
Shimming Help
I have a Leo Vince Slip on on my 2012 250. When i decelerate it makes small backfire pops. also takes a while to warm up even with choke fully on. Have not removed the snorkle either. Live at sea level and have 1600 mile on it. Should I shim the needles? would that take care of the problem?
|
|
December 31st, 2012, 07:35 PM | #77 | |
Long Time Rider
Name: Blue
Location: Charlotte, NC
Join Date: Sep 2010 Motorcycle(s): 2009 Kawasaki Ninja 250R Posts: A lot.
|
Quote:
One reason you hear it (popping) so well is because you have an empty tin can instead of a heavily baffled steel drum. The popping noise can be reduced by doing the kleen air delete mod, which stops the extra air entering into the already lean exhaust. You can also shim the needles to add a tiny bit of richness to the mix. |
|
|
December 31st, 2012, 09:33 PM | #78 | |
Daily Jap rider
Name: Lance
Location: La Porte
Join Date: Dec 2012 Motorcycle(s): 2012 Ninja 250r Posts: A lot.
|
Quote:
|
|
|
January 13th, 2013, 12:38 AM | #79 |
ninjette.org member
Name: JOHAN
Location: PHILIPPInes
Join Date: Aug 2011 Motorcycle(s): YAMAHA X1, YAMAHA SNIPER 135LC, KawasaKi ninja 250r Posts: 185
|
did the shimming too after i mounted this beastly exhaust, she did run great,,id highly recommend it!
|
|
November 2nd, 2013, 09:00 AM | #80 |
ninjette.org member
Name: George
Location: vancouver
Join Date: Oct 2013 Motorcycle(s): 08 Ninja 250r Posts: 23
|
Just did this. Added 2 #4 washers per needle and the bike is acting so much better. She seems so happy now great mod.... recommended for everyone.... such a huge improvement. ... Thanks kkim
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Shimming the carb needles | kfilla | General Motorcycling Discussion | 2 | July 2nd, 2014 06:14 PM |
DIY Shimming the carb needles. | Viper-Byte | 2008 - 2012 Ninja 250R Tech Talk | 1078 | April 17th, 2014 10:16 PM |
DJ Needles instead of shimming | mxman38 | 2008 - 2012 Ninja 250R Tech Talk | 7 | May 30th, 2012 07:09 PM |
Need help on shimming carb needles | RedNinja21 | 2008 - 2012 Ninja 250R Tech Talk | 6 | October 27th, 2011 10:16 AM |
FREE!!! 3MM Washers for Shimming Your Carb Needles | kkim | 2008 - 2012 Ninja 250R Tech Talk | 1 | September 10th, 2010 02:26 AM |
Thread Tools | |
|
|