January 22nd, 2014, 09:26 PM | #1 |
ninjette.org member
Name: AZ
Location: Orlando FL
Join Date: Oct 2012 Motorcycle(s): 2002 Ninja 250 Posts: 213
|
-Vent
Edit: Title "Clutch Cable About To Snap"
I'm kind of stressing, the clutch cable on my 250 is about to snap right at the lever. I just noticed this tonight when i noticed the lever needed to be tightened. I think i got the basic concept down of shifting without the clutch, but any pointers or advice from someone that's gone through this would be nice. Since i noticed it, i've been clutchless upshifting as much as possible, but still relying on it for stops and the low gears. Basically, let the bike stall or hit the kill switch at lights/stops.. start in 1st with a little throttle and go.. and when i downshift, let the rpms fall low and blip the throttle. is this correct? Hopefully I can get this cable QUICK. I'm a commuter with no car..need to get to work in the morning. any way to rig it or prolong the rest of it's short life? Honestly, I didn't take a good look it was dark out. What i saw was the majority of the cable was ripper at the lever and only a few strands intact. |
|
January 22nd, 2014, 09:47 PM | #2 |
Participant
Name: Dave
Location: South of Seattle
Join Date: Oct 2012 Motorcycle(s): '94 K75 std Posts: Too much.
MOTM - Aug '15
|
Don't lose the little cable-end drum that goes on the hand lever end of the cable. And when you get the new cable, duct tape it to one end of the clutch cable you're removing and pull the new cable through so you get the routing correct.
You can ride (or drive a car) with no cliutch if you have to. On the bike, while stopped in neutral, push off forward and click it into first gear (can't really push off in a car...). Use the throttle to match engine speed/load to the correct shift points: tough to explain in words, but not that difficult if you gotta do it to get home. |
1 out of 1 members found this post helpful. |
January 22nd, 2014, 09:49 PM | #3 |
Daily Ninjette rider
Name: Hernan
Location: Florida
Join Date: Mar 2011 Motorcycle(s): 2007 Ninja 250 Posts: A lot.
MOTY - 2016, MOTM - Dec '12, Jan '14, Jan '15, May '16
|
The cable breaks when it gets bent.
They last forever if only under pure pulling forces. The most common reason for bending is poor lubrication of the head of the cable against the lever. The remaining threads may hold for a few more days if the head gets lubricated now (oil would be enough for that purpose). http://faq.ninja250.org/wiki/Can_I_r...able_breaks%3F
__________________________________________________
Motofool .................................Never ride faster than your guardian angel can fly "Mankind is composed of two sorts of men — those who love and create, and those who hate and destroy. Love is the bond between men, the way to teach and the center of the world." - José Martí |
|
January 22nd, 2014, 09:55 PM | #4 | |
Participant
Name: Dave
Location: South of Seattle
Join Date: Oct 2012 Motorcycle(s): '94 K75 std Posts: Too much.
MOTM - Aug '15
|
Quote:
|
|
|
January 22nd, 2014, 10:24 PM | #5 |
ninjette.org member
Name: AZ
Location: Orlando FL
Join Date: Oct 2012 Motorcycle(s): 2002 Ninja 250 Posts: 213
|
Thanks guys.
|
|
January 23rd, 2014, 03:57 AM | #6 |
ninjette.org guru
Name: harry
Location: Central Florida
Join Date: Sep 2013 Motorcycle(s): 2006 Ninja 250, 2004 Buell XB12s, Honda 110 Elite Posts: 332
|
cable lube trick
Old fart trick. Remove the lever, drill a hole in the top of the lever directly above the location of the cable barrel. Drop of oil every so often keeps things well lubed. I haven't broken a cable at the barrel fitting in something like 30 years.
__________________________________________________
"They don't pay me enough to ride this thing!" Kenny Roberts after winning the Indy Mile on the TZ750 powered Grand National bike. |
2 out of 2 members found this post helpful. |
January 23rd, 2014, 05:48 PM | #7 |
ninjette.org member
Name: AZ
Location: Orlando FL
Join Date: Oct 2012 Motorcycle(s): 2002 Ninja 250 Posts: 213
|
well guys, it snapped today about 2 miles into my ride even after i lubbed the hell out of it. I'm thinking it's the original cable, and the bike has 43kmiles (19 being mine i guess it was just it's time :/
so i made the remaining 30 mile round trip to work without the clutch at all. Not sure if learning and doing this in the morning Orlando rush hour traffic was a good thing, or bad thing. I did almost get rear ended when i was first at the light and it turns green and I stalled. Overall I think I stalled it 2 or 3 times on the way to work, and zero times on the way back, which was also during rush hour. The pushing off and sliding into first really helps. It slips right in. going through second and 3rd were pretty jerky, but the rest of the gears i could do kinda smoothly. A lot of my down shifts were pretty smooth, some non existent. I'm surprised how easy it is to ride without using the clutch at all. Luckily I'm off work tomorrow and the shop in town has them instock, $18. Only hiccup is that it's about a 50mile roundtrip, half highway miles. How much damage am I doing riding like this? I might be able to get a ride though...keyword might. |
|
January 23rd, 2014, 06:00 PM | #8 | |
ninjette.org certified postwhore
Name: Fish
Location: co
Join Date: Apr 2013 Motorcycle(s): 250/300 Posts: A lot.
|
Quote:
__________________________________________________
Hey Unregistered never go faster than your brakes can be applied... |
|
|
January 23rd, 2014, 06:32 PM | #9 | |
Participant
Name: Dave
Location: South of Seattle
Join Date: Oct 2012 Motorcycle(s): '94 K75 std Posts: Too much.
MOTM - Aug '15
|
Quote:
The bike'll be fine: you wore some of the sharp edges off of the shift dogs. No harm. Congratulations! |
|
|
January 23rd, 2014, 07:15 PM | #10 | |
Private Joker
Name: Ben
Location: Towson, MD
Join Date: Nov 2012 Motorcycle(s): '99/'01 Ninja 250 "sketchy", '13 Ninja 300 "yoshi", '03 GSXR 600 "merlin" Posts: A lot.
MOTM - Mar '14
|
Quote:
edit: don't worry about any damage done riding without the clutch, it'll take a lot more than 1 day of clutchless riding to damage a straight transmission like the ones in our ninjettes |
|
|
January 23rd, 2014, 07:20 PM | #11 |
Participant
Name: Dave
Location: South of Seattle
Join Date: Oct 2012 Motorcycle(s): '94 K75 std Posts: Too much.
MOTM - Aug '15
|
|
|
January 23rd, 2014, 07:34 PM | #12 | |
ninjette.org certified postwhore
Name: Fish
Location: co
Join Date: Apr 2013 Motorcycle(s): 250/300 Posts: A lot.
|
Quote:
__________________________________________________
Hey Unregistered never go faster than your brakes can be applied... |
|
|
January 23rd, 2014, 07:36 PM | #13 |
Private Joker
Name: Ben
Location: Towson, MD
Join Date: Nov 2012 Motorcycle(s): '99/'01 Ninja 250 "sketchy", '13 Ninja 300 "yoshi", '03 GSXR 600 "merlin" Posts: A lot.
MOTM - Mar '14
|
|
|
January 23rd, 2014, 07:47 PM | #14 |
ninjette.org certified postwhore
Name: Fish
Location: co
Join Date: Apr 2013 Motorcycle(s): 250/300 Posts: A lot.
|
I wish that been epic. No I was setting on it with my son on the tank and he is play driving Hits the button and it kicks out and I rather save him so in doing so I dropped the bike..
__________________________________________________
Hey Unregistered never go faster than your brakes can be applied... |
1 out of 1 members found this post helpful. |
January 23rd, 2014, 07:49 PM | #15 |
Private Joker
Name: Ben
Location: Towson, MD
Join Date: Nov 2012 Motorcycle(s): '99/'01 Ninja 250 "sketchy", '13 Ninja 300 "yoshi", '03 GSXR 600 "merlin" Posts: A lot.
MOTM - Mar '14
|
well, if it's any consolation. you definitely made the right choice.
|
1 out of 1 members found this post helpful. |
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
WTH?!?! Vent here... | deeno415 | Off-Topic | 10 | September 5th, 2013 12:12 PM |
What is this vent outlet? | delscorcho | 2008 - 2012 Ninja 250R Tech Talk | 2 | July 22nd, 2012 05:25 PM |
What is this? (vent tube) | edbro | 2008 - 2012 Ninja 250R Tech Talk | 7 | December 28th, 2009 10:55 AM |
|
|