|
May 14th, 2009, 08:52 PM
|
#1 |
|
ninjette.org member
Name: Shish
Location: SGV, CA
Join Date: Apr 2009 Motorcycle(s): Ninja 250 Posts: 35
|
WTB: Rear Side Reflector
Apparently i lost or someone stole one of my rear side reflectors (the red circle one).
Not sure what happened to it because i definitely did not remove it, nor did it break off because it is held on by a bolt and nut? Anywho, i need only one and if anyone can sell me one i would appreciate it. Would be nice if you just had it laying around after doing a fender eliminator and didn't need it. I'm in socal, is this specific for the 08+ 250? 
|
|
|
|
May 15th, 2009, 08:08 AM
|
#2 |
|
ninjette.org sage
Name: Tim
Location: Portland, OR
Join Date: Dec 2008 Motorcycle(s): 2009 SE Ninja 250R Posts: 796
|
I have mine lying around that I could just give you but shipping might be a killer... Let me know if you can't find anything closer... and ya, they're 08+ specific or atleast they're not on the Canadian ZZRs...
and welcome to the forums! |
|
|
|
|
May 15th, 2009, 08:39 AM
|
#3 |
|
ninjette.org certified postwhore
Name: Travis
Location: Warwick, RI
Join Date: Apr 2009 Motorcycle(s): 2009 Ninja 250R Posts: A lot.
|
You can get identical ones for about 5 bucks at AutoZone.
__________________________________________________
Addicted to anything that has an engine and rolls. 
|
|
|
|
|
May 15th, 2009, 12:20 PM
|
#4 |
|
ninjette.org member
Name: Shish
Location: SGV, CA
Join Date: Apr 2009 Motorcycle(s): Ninja 250 Posts: 35
|
Nemy, thank you! But yeah, shipping will probably be a killer. I will let you know if i can't find one locally.
tjkamper, thanks! I will have to check it out later today. I don't have the bike with me, but do these reflectors have a hole through them for the bolt to go through? I would have to get a nut and bolt too. |
|
|
|
|
May 15th, 2009, 12:51 PM
|
#5 |
|
ninjette.org certified postwhore
Name: Travis
Location: Warwick, RI
Join Date: Apr 2009 Motorcycle(s): 2009 Ninja 250R Posts: A lot.
|
When I saw them last week. It was a set of two and they were the bolt there was a net the goes on the back of your plate to hold them on. Similar to his pic but a little bit different because it thought it was actually threaded. It might of had a wing nut on the back instead of a hex head, but it all tightens right?
__________________________________________________
Addicted to anything that has an engine and rolls.
|
|
|
|
|
May 15th, 2009, 12:53 PM
|
#6 |
|
ninjette.org certified postwhore
Name: Travis
Location: Warwick, RI
Join Date: Apr 2009 Motorcycle(s): 2009 Ninja 250R Posts: A lot.
|
These are them. A few minutes patience searching the internet goes a long way.
__________________________________________________
Addicted to anything that has an engine and rolls.
|
|
|
|
|
June 18th, 2009, 09:16 PM
|
#7 |
|
ninjette.org newbie
Name: fer
Location: california
Join Date: Jun 2009 Motorcycle(s): (sold)--2008 250 ninja currently 2008 zx6r Posts: 7
|
u can have mine..but u gotta pick them up though...and they are the oem ones too....just let me double check make sure i didnt throw them away
|
|
|
|
 |
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| WTB Right side stock rear set. | MissyNinja | Items Wanted | 1 | February 12th, 2014 11:38 AM |
| WTB Right Side Rear Mirror | caphilli | Items Wanted | 0 | November 11th, 2011 11:36 PM |
| WTB New Gen Right Side Rear Set | RacerX113 | Items Wanted | 0 | July 21st, 2011 09:29 AM |
| WTB CF Side Panel and Rear Hugger | sherjay | Items Wanted | 0 | February 18th, 2011 11:10 PM |
|
|
