September 7th, 2011, 12:18 AM | #1 |
ninjette.org member
Name: Nelson
Location: Jackson MI
Join Date: Aug 2011 Motorcycle(s): 2010 Ninja 250R SE Posts: 41
|
Koso RX2 Gauge with voltmeter?
I am looking for the Koso RX2 gauge with voltmeter. I have found the gauge itself but not the voltmeter along with it. Also I am not sure if it will fit on the bike with no other mods needed or if I have to restructure the mounts to it will fit.
|
|
September 7th, 2011, 12:31 AM | #2 |
Ninjette wanabe :D
Name: Ruslan
Location: San Jose
Join Date: Apr 2011 Motorcycle(s): white 300 :D Posts: A lot.
|
Most or all voltmeter koso dashs come out from indonesia.
__________________________________________________
VROOOM vrooom >.> |
|
September 7th, 2011, 07:44 PM | #3 |
ninjette.org member
Name: Nelson
Location: Jackson MI
Join Date: Aug 2011 Motorcycle(s): 2010 Ninja 250R SE Posts: 41
|
I have found them all over the place. But I cant find the voltmeters along with it
|
|
September 7th, 2011, 08:44 PM | #4 |
ninjette.org certified postwhore
Name: Wayan
Location: Bali - Indonesia
Join Date: Apr 2009 Motorcycle(s): 2014 Z250 Posts: A lot.
|
dont think the "kits" with the voltmeter, and custom brackets are available in the states yet. ive send like 4 kits to the states so far, and 2 custom dashboards for ppl that already owned the speedo itself, but didnt like the koso dash.
http://youtu.be/K4mB_OmGezc thats the last one i sent over to california, posted a short vid of it starting up. the price (excluding shipping) is: koso RX2N/RX2N + custom bracket + voltmeter) = $410 koso RX2N/RX2N + custom bracket) = $350 this price is including a 15% mark up, more than half of which gets gobbled up by PayPal... one person wanted the voltmeter, while the other 2 didnt want it, when i bought these three during a GB. W.
__________________________________________________
Kawasaki Z250, Bored up to 300cc with 12.8 CR, 41hp at wheel 27nm torque, Two bros full exhaust with DB killer Dynojet Power Commander V, KnN Open filter, intake and exhaust ported, Puig Windshield |
|
September 7th, 2011, 09:00 PM | #5 |
ninjette.org member
Name: Nelson
Location: Jackson MI
Join Date: Aug 2011 Motorcycle(s): 2010 Ninja 250R SE Posts: 41
|
lol so is there a place that sells them?
|
|
September 7th, 2011, 09:08 PM | #6 |
ninjette.org certified postwhore
Name: Wayan
Location: Bali - Indonesia
Join Date: Apr 2009 Motorcycle(s): 2014 Z250 Posts: A lot.
|
in america? not that im aware of... but i could be wrong, since i have never looked for anyone selling them there. although i am surprised that no one is selling these kits over there already, since there would be a reasonably big demand for them if it were available.
so you would still have to get it from here in Indonesia at this point in time.
__________________________________________________
Kawasaki Z250, Bored up to 300cc with 12.8 CR, 41hp at wheel 27nm torque, Two bros full exhaust with DB killer Dynojet Power Commander V, KnN Open filter, intake and exhaust ported, Puig Windshield |
|
September 7th, 2011, 09:10 PM | #7 |
ninjette.org member
Name: Nelson
Location: Jackson MI
Join Date: Aug 2011 Motorcycle(s): 2010 Ninja 250R SE Posts: 41
|
you have a link? I can get the RX2 from almost any website that sells bike stuff. But I can not find it with the voltmeter..
|
|
September 7th, 2011, 09:16 PM | #8 |
ninjette.org certified postwhore
Name: Wayan
Location: Bali - Indonesia
Join Date: Apr 2009 Motorcycle(s): 2014 Z250 Posts: A lot.
|
the voltmeter is from Koso too actually, if you google "koso voltmeter" you get pictures of the same one that i get with the kits here. not sure what the item# is, i think you can find that or even a place to buy it online if you look through some of those links.
as reference, i think i can get the voltmeter for about $68 here. and the custom fiberglass bracket costs about the same. gl!
__________________________________________________
Kawasaki Z250, Bored up to 300cc with 12.8 CR, 41hp at wheel 27nm torque, Two bros full exhaust with DB killer Dynojet Power Commander V, KnN Open filter, intake and exhaust ported, Puig Windshield |
|
September 7th, 2011, 09:26 PM | #9 |
ninjette.org member
Name: Nelson
Location: Jackson MI
Join Date: Aug 2011 Motorcycle(s): 2010 Ninja 250R SE Posts: 41
|
thanks. ill keep my eye out but have yet to find it..
|
|
September 8th, 2011, 02:28 AM | #10 |
ninjette.org certified postwhore
Name: Wayan
Location: Bali - Indonesia
Join Date: Apr 2009 Motorcycle(s): 2014 Z250 Posts: A lot.
|
if you go to:
http://www.kosonorthamerica.com/ then select motorcycle parts, and go on page 4, there is a voltmeter that looks the same, just that the color of the light is Blue, rather than red. item: DL-01 VOLT METER Code: BA484B30 however its still: Available soon... and way more expensive! $159.95
__________________________________________________
Kawasaki Z250, Bored up to 300cc with 12.8 CR, 41hp at wheel 27nm torque, Two bros full exhaust with DB killer Dynojet Power Commander V, KnN Open filter, intake and exhaust ported, Puig Windshield |
|
September 8th, 2011, 07:10 AM | #11 |
ninjette.org certified postwhore
Name: Jason
Location: Jacksonville, Florida
Join Date: May 2010 Motorcycle(s): 09 Ninja 250R SE, 07 Honda CRF230F, 06 Honda CRF150F Posts: A lot.
|
Nelson: Wayan is trying to tell you he can get everything you need. It just has to come from Indonesia and be shipped to the States. No biggie. I ordered one from him and I ABSOLUTELY LOVE IT!
__________________________________________________
09 250R SE: Paying it forward one post at a time! Don't forget to add yourself to our Member Map |
|
September 8th, 2011, 09:27 AM | #12 |
ninjette.org certified postwhore
Name: Wayan
Location: Bali - Indonesia
Join Date: Apr 2009 Motorcycle(s): 2014 Z250 Posts: A lot.
|
noooooo... i wasn't trying to say that! lol....
well maybe i was hinting that it is possible to get it from here if he wasn't able to get it any other way, the option is there, but it would be easier if it were available over there. int. shipping sorta hurts the wallet >.<
__________________________________________________
Kawasaki Z250, Bored up to 300cc with 12.8 CR, 41hp at wheel 27nm torque, Two bros full exhaust with DB killer Dynojet Power Commander V, KnN Open filter, intake and exhaust ported, Puig Windshield |
|
September 8th, 2011, 10:40 AM | #13 |
ninjette.org member
Name: Nelson
Location: Jackson MI
Join Date: Aug 2011 Motorcycle(s): 2010 Ninja 250R SE Posts: 41
|
hahaha well thank you for the offer wayan, and thanks again for the link. that site seems to be absolutely perfect! When you order the RX2 does it come with the mount and brackets and everything so that the voltmeter can be installed along with it or is their more that has to be ordered
|
|
September 8th, 2011, 06:12 PM | #14 |
ninjette.org certified postwhore
Name: Wayan
Location: Bali - Indonesia
Join Date: Apr 2009 Motorcycle(s): 2014 Z250 Posts: A lot.
|
the standard koso dash looks like this:
(gear indicator is optional, and only works with EFI models) while the custom bracket we get made here in indonesia looks like this: so you cant fit the voltmeter on koso's bezel, unless they have made some recent changes that im not aware of~ W.
__________________________________________________
Kawasaki Z250, Bored up to 300cc with 12.8 CR, 41hp at wheel 27nm torque, Two bros full exhaust with DB killer Dynojet Power Commander V, KnN Open filter, intake and exhaust ported, Puig Windshield |
|
September 8th, 2011, 11:12 PM | #15 |
ninjette.org member
Name: Nelson
Location: Jackson MI
Join Date: Aug 2011 Motorcycle(s): 2010 Ninja 250R SE Posts: 41
|
alright just to humor me, do you know how much it is for the koso gauge along with the voltmeter and the whole nine yards? and if you know how much it would be to ship to the states roughly. bc so far I cant find that whole setup around here or on the web
|
|
September 8th, 2011, 11:59 PM | #16 |
ninjette.org certified postwhore
Name: Wayan
Location: Bali - Indonesia
Join Date: Apr 2009 Motorcycle(s): 2014 Z250 Posts: A lot.
|
scroll up to link #4,
or click on this link if thats easier, lolz http://www.ninjette.org/forums/showp...36&postcount=4 i already posted it the other day.
__________________________________________________
Kawasaki Z250, Bored up to 300cc with 12.8 CR, 41hp at wheel 27nm torque, Two bros full exhaust with DB killer Dynojet Power Commander V, KnN Open filter, intake and exhaust ported, Puig Windshield |
|
September 9th, 2011, 12:02 AM | #17 |
ninjette.org member
Name: Nelson
Location: Jackson MI
Join Date: Aug 2011 Motorcycle(s): 2010 Ninja 250R SE Posts: 41
|
haha yea im blind. Anyway, does that include everything I will need to install it? It says something about already having the speedo, I am mechanically retarded so forgive me if im asking dumb questions, so im not sure if i will need anything else. And how do I go about buying it? from you?
|
|
September 9th, 2011, 12:28 AM | #18 |
ninjette.org certified postwhore
Name: Wayan
Location: Bali - Indonesia
Join Date: Apr 2009 Motorcycle(s): 2014 Z250 Posts: A lot.
|
its a Plug and play kit. you only have to plug in the 2 temp sensors (water and oil), run a cable to the battery for the power source, and a cable down the front forks to the magnet sensor for the speed reeading.
the only "mechanical" thing you will really need to do is remove the side and front farings, to remove the old speedo, and bolt in the new kit. as long as you have a set of allenkeys you are basically set! the rest is set up on the koso, you need to dial in that its a 4 stroke engine, 2 pistons, number of magnets, radius of the front wheel, the time, and then your set. o ya, u need a wrench to install the temp sensors, hehe
__________________________________________________
Kawasaki Z250, Bored up to 300cc with 12.8 CR, 41hp at wheel 27nm torque, Two bros full exhaust with DB killer Dynojet Power Commander V, KnN Open filter, intake and exhaust ported, Puig Windshield |
|
September 9th, 2011, 12:33 AM | #19 |
ninjette.org member
Name: Nelson
Location: Jackson MI
Join Date: Aug 2011 Motorcycle(s): 2010 Ninja 250R SE Posts: 41
|
Perfect! How can I get one? Looks like payin to ship it to the states is the only way to go. So im ready to order
|
|
September 9th, 2011, 02:13 AM | #20 |
ninjette.org certified postwhore
Name: Wayan
Location: Bali - Indonesia
Join Date: Apr 2009 Motorcycle(s): 2014 Z250 Posts: A lot.
|
what might be the cheaper and more secure solution would be to just buy the custom bracket and the voltmeter from here, and buy the Koso speedometer in america. they also have a P&P harnes kit for the ninja250.
the only difference is that you will need to splice in the voltmeter yourself. the rest should be roughly the same. that would cost $145 for the voltmeter and bracket only. this would make the shipping cheaper too, since it would be much lighter, than sending the whole kit. that's another idea for you to consider. W
__________________________________________________
Kawasaki Z250, Bored up to 300cc with 12.8 CR, 41hp at wheel 27nm torque, Two bros full exhaust with DB killer Dynojet Power Commander V, KnN Open filter, intake and exhaust ported, Puig Windshield |
|
September 9th, 2011, 01:13 PM | #21 |
ninjette.org member
Name: Nelson
Location: Jackson MI
Join Date: Aug 2011 Motorcycle(s): 2010 Ninja 250R SE Posts: 41
|
No that absolutely sounds like a good plan. Would it be easy to buy the harness from over there as well. Or will come with the koso gauge?
|
|
September 9th, 2011, 01:35 PM | #22 |
ninjette.org sage
Name: L
Location: WI
Join Date: Apr 2011 Motorcycle(s): '09 250R, '13 CBR500R Posts: 709
|
the harness can be bought in the states for $50.
http://cgi.ebay.com/ebaymotors/KOSO-...item5645bb4f1b koso RX-2 gauge can be had here for ~ $300 http://www.biohazardcycles.com/servl...DOMETER/Detail so that's ~$350 + $150 (bezel + voltmeter not including shipping from Wayan). so roughly $500 total and no shipping costs from indo included yet. at this point i'd rather say just buy it COMPLETE from Wayan and pay international shipping. LOL. there was a GB for the Koso gauges headed up by Outlander. Not sure if it's complete or still going on. |
|
September 9th, 2011, 02:11 PM | #23 |
ninjette.org member
Name: Nelson
Location: Jackson MI
Join Date: Aug 2011 Motorcycle(s): 2010 Ninja 250R SE Posts: 41
|
thank GT that will be what I will do!
Wayan is there a company that sells this stuff over there or who do I cut a check too so to speak |
|
September 9th, 2011, 06:10 PM | #24 |
ninjette.org certified postwhore
Name: Wayan
Location: Bali - Indonesia
Join Date: Apr 2009 Motorcycle(s): 2014 Z250 Posts: A lot.
|
no company here "exports" these so to speak. i buy the kits from a shop, test them, pack them properly and send them out by DHL or whatever you choose for the shipping.
i can accept PayPal, which is something that almost no one here in indonesia accepts. i havent send a single Koso Kit by DHL, the other times i sent them was bundled up with other bits, so i cant give a price in advance for that until i get DHL to price it. there is also a insurance % that is charged on top by dhl. for the last package i declared the goods at half (or quarter) the price, since it was over $1000 worth of goods, and it would have cost another $50 for the insurance... thats also something that you can decide once we get the shipping price by DHL. you might want to join the GB, which is still in a bit of a limbo, which Outlander is heading up from the state side. im just waiting for the green light, and the $$ before i do anything on my end. i cant find the thread tho... post there and i should get a notification if you find it, hehe. enjoy your week end! W.
__________________________________________________
Kawasaki Z250, Bored up to 300cc with 12.8 CR, 41hp at wheel 27nm torque, Two bros full exhaust with DB killer Dynojet Power Commander V, KnN Open filter, intake and exhaust ported, Puig Windshield |
|
September 11th, 2011, 03:43 PM | #25 |
ninjette.org member
Name: Nelson
Location: Jackson MI
Join Date: Aug 2011 Motorcycle(s): 2010 Ninja 250R SE Posts: 41
|
alright well let me get something things in order over here and i will PM you for the details of what needs to happen from here
|
|
June 21st, 2012, 09:41 AM | #26 | |
ಠ_ಠ
Name: Janelle
Location: Hawaii
Join Date: May 2012 Motorcycle(s): current newbie stick is a loaner :P Posts: 257
|
Quote:
I really like the RX-2 for the ability to change backlight, but am hating the asymmetry of it. Would a model like the RX-1N need a bezel?
__________________________________________________
a fast ride isn't necessarily a fun ride ;3 |
|
|
June 21st, 2012, 10:01 AM | #27 |
ninjette.org certified postwhore
Name: Jason
Location: Jacksonville, Florida
Join Date: May 2010 Motorcycle(s): 09 Ninja 250R SE, 07 Honda CRF230F, 06 Honda CRF150F Posts: A lot.
|
Those are function buttons to go thru the menu and select settings and such. They also switch between oil or water temp displayed ,reset the trip meter, etc.
__________________________________________________
09 250R SE: Paying it forward one post at a time! Don't forget to add yourself to our Member Map |
|
June 21st, 2012, 10:05 AM | #28 |
ninjette.org member
Name: John
Location: Buffalo NY
Join Date: Sep 2009 Motorcycle(s): Ninja Posts: 122
|
They're function buttons.
|
|
June 21st, 2012, 10:42 AM | #29 | |
ಠ_ಠ
Name: Janelle
Location: Hawaii
Join Date: May 2012 Motorcycle(s): current newbie stick is a loaner :P Posts: 257
|
Quote:
How about that bezel? o_O
__________________________________________________
a fast ride isn't necessarily a fun ride ;3 |
|
|
June 21st, 2012, 12:30 PM | #30 |
ಠ_ಠ
Name: Janelle
Location: Hawaii
Join Date: May 2012 Motorcycle(s): current newbie stick is a loaner :P Posts: 257
|
Woah... Whoops. Didn't mean to revive a dead thread. :S
__________________________________________________
a fast ride isn't necessarily a fun ride ;3 |
|
June 21st, 2012, 12:33 PM | #31 |
ninjette.org certified postwhore
Name: Jason
Location: Jacksonville, Florida
Join Date: May 2010 Motorcycle(s): 09 Ninja 250R SE, 07 Honda CRF230F, 06 Honda CRF150F Posts: A lot.
|
No thread is dead unless it is closed.
__________________________________________________
09 250R SE: Paying it forward one post at a time! Don't forget to add yourself to our Member Map |
|
June 7th, 2017, 02:50 AM | #32 |
ninjette.org newbie
Name: Victor
Location: Canada
Join Date: Jun 2017 Motorcycle(s): Ninja 250r Posts: 2
|
still selling? i need a place to put my air/fuel ratio gauge. and that voltmeter spot looks perfect since i think the voltmeter is kind of useless. can i just get the koso rx2 with the mount with that space to the left? i can drill a hole for my current a/f r guage myself =D
and how do i reach you? |
|
June 12th, 2017, 08:50 AM | #33 | |
ninjette.org certified postwhore
Name: Wayan
Location: Bali - Indonesia
Join Date: Apr 2009 Motorcycle(s): 2014 Z250 Posts: A lot.
|
Heya, would you be getting the Koso gauge from Koso USA? i find that to be the easier solution, if i just need to order and ship the bezel.
i would have to check again what they cost but if your interested i can look into it. last time i sent a bracket for a fellow member, Steve, that was back in April 2016. it cost $50 for a bracket, and shipping to Long Beach, NJ. can email me at wayanlam@gmail.com Quote:
__________________________________________________
Kawasaki Z250, Bored up to 300cc with 12.8 CR, 41hp at wheel 27nm torque, Two bros full exhaust with DB killer Dynojet Power Commander V, KnN Open filter, intake and exhaust ported, Puig Windshield |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Koso Rx1 or Rx2 gauge contents and extras? | Daakuryu | 2008 - 2012 Ninja 250R Farkles | 12 | April 12th, 2021 12:13 PM |
need help with koso gauge | Old Lemon | 2008 - 2012 Ninja 250R Tech Talk | 8 | August 13th, 2012 01:04 PM |
How long have you had your Koso gauge? | CThunder-blue | 2008 - 2012 Ninja 250R Farkles | 8 | July 10th, 2012 01:40 PM |
Koso gauge | randomwalk101 | Motorcycle-related | 7 | November 5th, 2010 07:28 PM |
Koso gauge kit GB | wellcraft | Motorcycle-related | 56 | April 29th, 2010 07:31 PM |
|
|