Forum: 2008 - 2012 Ninja 250R Tech Talk
November 25th, 2016, 07:13 AM
|
Replies: 31
Views: 9,156
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
September 27th, 2016, 07:53 AM
|
Replies: 3
Views: 1,314
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
July 28th, 2016, 04:39 AM
|
Replies: 6
Views: 1,183
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
July 17th, 2016, 06:48 AM
|
Replies: 28
Views: 5,023
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
July 9th, 2016, 06:44 AM
|
Replies: 10
Views: 3,657
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
July 4th, 2016, 07:58 AM
|
Replies: 43
Views: 22,422
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
July 2nd, 2016, 06:27 AM
|
Replies: 10
Views: 3,657
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
July 1st, 2016, 09:05 AM
|
Replies: 1
Views: 957
5/8 inner diameter, rubber base works.
...
5/8 inner diameter, rubber base works.
Cleanest way to do it is to use an enclosed air/oil separator breather similar to this. You can get push on or thread on, or just weld them like this guy...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
July 1st, 2016, 08:41 AM
|
Replies: 4
Views: 2,074
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
June 21st, 2016, 05:34 AM
|
Replies: 3
Views: 1,538
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
June 21st, 2016, 04:49 AM
|
Replies: 23
Views: 3,032
oil and water pump are gearbox driven so the...
oil and water pump are gearbox driven so the engine would be moving oil and coolant. Cold fluids, but circulating none the less.
The excess rpm is the issue if it was in first. At 45 it would be...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
June 21st, 2016, 04:30 AM
|
Replies: 5
Views: 1,216
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
July 7th, 2015, 04:08 AM
|
Replies: 10
Views: 2,381
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
July 6th, 2015, 09:11 PM
|
Replies: 10
Views: 2,381
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
July 4th, 2015, 11:19 PM
|
Replies: 10
Views: 2,381
Barnett Clutch Kit
Does anyone have any experience with these? Does the black/blue plate go first or last?
http://i1358.photobucket.com/albums/q775/tubarney/IMG_0074_zpsfir4pno9.jpg...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
October 21st, 2014, 06:54 AM
|
Replies: 9
Views: 5,293
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
May 14th, 2014, 11:32 PM
|
Replies: 1,204
Views: 111,956
Sorry to hear the bad news Mike. At least it is...
Sorry to hear the bad news Mike. At least it is only a head problem.
In 4 weeks my plan is to live up to my word and post a dyno of mine with CR carbs. Been tied up with some bulls*** for the last...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
May 14th, 2014, 10:04 PM
|
Replies: 21
Views: 8,311
I've run as low as 8 psi in the rear.
25-35...
I've run as low as 8 psi in the rear.
25-35 psi for commuting
15-25 psi for the twisties.
The lower pressure you go:
The less miles you will get.
Your turn in will get worse (tire will...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
May 14th, 2014, 09:52 PM
|
Replies: 147
Views: 43,805
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
May 3rd, 2014, 10:25 PM
|
Replies: 1,204
Views: 111,956
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
May 3rd, 2014, 10:14 PM
|
Replies: 4
Views: 727
If there is supposed to be movement (which I...
If there is supposed to be movement (which I doubt); there isn't supposed to be that much.
Machining error. Could be crank (that sprocket is almost impossible to move), balance shaft itself or...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
April 26th, 2014, 06:37 AM
|
Replies: 17
Views: 1,650
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
April 21st, 2014, 03:44 AM
|
Replies: 10
Views: 4,477
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
January 4th, 2014, 06:06 AM
|
Replies: 6
Views: 1,467
What he said^.
Drain the coolant. Spend the...
What he said^.
Drain the coolant. Spend the 10 bucks and save yourself a lot of trouble:thumbup:.
If coolant still good, be a tight ass like me, drain into clean bucket, then use coffee filters...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
January 4th, 2014, 05:57 AM
|
Replies: 16
Views: 3,570
|