Forum: 2008 - 2012 Ninja 250R Tech Talk
January 4th, 2011, 02:39 PM
|
Replies: 8
Views: 1,349
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
January 4th, 2011, 07:13 AM
|
Replies: 8
Views: 1,349
Afraid I eyeballed what size since i had an...
Afraid I eyeballed what size since i had an assortment of T-fittings and vacuum caps..did end up using the 1/8" ID fuel line though. Just out of curiousity, would it make any difference if I...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
January 3rd, 2011, 07:46 AM
|
Replies: 8
Views: 1,349
Synch. carb setup hint
Last year I added a T fitting to the 2 vacuum lines that run from the carbs to the fuel switch, et. al. and capped off the open ports which were to attach to my synch guage when needed with rubber...
|
Forum: Motorcycle-related
April 12th, 2010, 09:29 PM
|
Replies: 31
Views: 3,256
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
November 23rd, 2009, 05:19 PM
|
Replies: 7
Views: 2,032
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
October 22nd, 2009, 07:16 PM
|
Replies: 11
Views: 1,839
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
October 22nd, 2009, 07:01 PM
|
Replies: 11
Views: 1,839
Nice even thin layer of Copper HiTemp Permatex...
Nice even thin layer of Copper HiTemp Permatex RTC on end of pipe should seal it..let it cure a few hours before "lighting" her up. Lay a line of RTV on the cannister inside connector on each of...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
October 22nd, 2009, 06:44 PM
|
Replies: 21
Views: 7,681
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
October 22nd, 2009, 06:37 PM
|
Replies: 11
Views: 1,839
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
October 22nd, 2009, 06:27 PM
|
Replies: 21
Views: 7,681
|
Forum: Motorcycle-related
October 19th, 2009, 11:21 AM
|
Replies: 9
Views: 1,030
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
October 18th, 2009, 07:33 PM
|
Replies: 27
Views: 5,001
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
October 18th, 2009, 07:26 PM
|
Replies: 206
Views: 41,617
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
October 18th, 2009, 10:51 AM
|
Replies: 206
Views: 41,617
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
October 18th, 2009, 10:48 AM
|
Replies: 13
Views: 1,940
|
Forum: Off-Topic
October 18th, 2009, 10:46 AM
|
Replies: 28
Views: 1,547
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
October 18th, 2009, 09:19 AM
|
Replies: 13
Views: 1,940
PreGen Shock..fit NewGen?
Quicky question as title asks..are the mounts the same for a 07 and prior 250 and the NewGen 08-10's ? Interchangeable ?
THX
|
Forum: Off-Topic
October 18th, 2009, 08:55 AM
|
Replies: 28
Views: 1,547
|
Forum: Off-Topic
October 18th, 2009, 06:58 AM
|
Replies: 28
Views: 1,547
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
October 18th, 2009, 06:40 AM
|
Replies: 206
Views: 41,617
Pretty much what I have done for the last 40...
Pretty much what I have done for the last 40 years...Stabil instead of Seafoam. My experience with an empty gas tank and dry carbs has been rust and hung up float valves and dry seals even when I...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
October 17th, 2009, 01:44 PM
|
Replies: 4
Views: 2,291
Thanks for your time...I guess I am confused by...
Thanks for your time...I guess I am confused by how to tell the difference between my making the bike richer(resnorkling) and not being able to rev past 8K...it just "bogged" here and the "too lean,...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
October 17th, 2009, 12:47 PM
|
Replies: 4
Views: 2,291
Rich vs. Lean question
Wonder if I could get some feedback on the following. My 08 Ninja seemed less "cold blooded" from the factory. Put 1 washer in and desnorkled to richen things up in the intermediate-high range and...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
October 17th, 2009, 12:37 PM
|
Replies: 27
Views: 5,001
Hey Manoj..
Did this just start...
Hey Manoj..
Did this just start happening..?...try putting your snorkel back in (hard to get completely back in but you can shove it in pretty close if you pry on the grooved lips) and see what...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
October 15th, 2009, 03:03 PM
|
Replies: 90
Views: 23,553
There is one distributor who states the 10-32...
There is one distributor who states the 10-32 will work with our 5mm bolts...not the case as I found out...you can screw the 5mm's into a 10-32 nut with some effort but you get one shot since it...
|
Forum: 2008 - 2012 Ninja 250R Tech Talk
October 11th, 2009, 04:52 AM
|
Replies: 6
Views: 1,019
|