June 19th, 2015, 10:41 AM | #1 |
RIP Alex
Name: Cuong
Location: Houston, TX
Join Date: Apr 2011 Motorcycle(s): '10 250r, '09 265r Posts: A lot.
Blog Entries: 2
|
Cam chain tensioners: Why do some go bad?
Why is it that some just go bad? @spooph I think I recall you taking the new ones apart so maybe you can offer some insight?
__________________________________________________
HalfFast Racing Team Serving Greater Houston Area Riders:WFO Riders MotoHouston HPC CMRA Ride Smart Fastline Lone Star Track Days |
|
June 19th, 2015, 04:13 PM | #2 |
ninjette.org certified postwhore
Name: Spooph
Location: Golden, CO
Join Date: Jul 2010 Motorcycle(s): '08 Ninja 250R Posts: A lot.
MOTM - Oct '15
|
what do you mean by "some just go bad"?
I wouldn't say they go bad. I think Kawi didn't write instructions, or include in the maintenance schedule that they should be maintained, and therefor nobody maintains them. The new-gen design was definitely over-engineered, and I think was meant to be maintenance free, which is why it's such a pain and therefor not on the maintenance schedule but I think that's Kawi being over-confident. All of the ones I've looked at tended to start getting less than optimal results after 30K, some higher than that. I'm not sure if mileage though, as time seems to play a large factor here too... Moisture, heat/cold (being run in adverse and cold conditions) don't seem to help them either. So, I don't mean to scare anybody, but if you're camchain isn't quiet your could probably use a rebuild. If "going bad" means failure, I saw a pre-gen properly "fail" when the spring actually broke inside, but that's the only one I've ever seen properly "fail". If anybody wants their's rebuild, I'm sure we can figure something out. Otherwise I'll have some time here in the next few weeks to do a write-up on how to do it yourself. Mind you, it is not easy. If you guys want that write-up, please remind me as I tend to forget things - it's a huge flaw and I know, please help me out. Hope this helps.
__________________________________________________
My therapist has 2 wheels and a seat. If you are ever in doubt to my tone, please refer to my avatar. |
|
June 19th, 2015, 04:54 PM | #3 |
in your machine
Name: Scott
Location: Summer Shade, Ky.
Join Date: Oct 2014 Motorcycle(s): 98 Ninja 250/F12 aka ZX-2R "SERENITY", 91 Ninja 500/A5 aka ZX-5R "Phoenix", 84 Honda GL1200A "SIREN" Posts: A lot.
Blog Entries: 25
MOTM - Jun '17, May '16, Mar '15
|
@spooph does the NewGen one work on the PreGen?
There's a similar issue with the EX500, but it's an easy fix just bolt on one from a 2nd Gen(94&up) and your all set, the 2nd Gen is a better design than 1st Gen.
__________________________________________________
violente et ignorantia ZX-2R BLOG Twitter and Instagram = Ghostt_Scott I'm not here to change your mind, just to inform. |
|
June 19th, 2015, 05:05 PM | #4 |
RIP Alex
Name: Cuong
Location: Houston, TX
Join Date: Apr 2011 Motorcycle(s): '10 250r, '09 265r Posts: A lot.
Blog Entries: 2
|
When I said bad, I was referring to the intermittent ticking. It's a whole lot more prominent now on startup. I might change the oil and see if it helps.
Then proceed with a valve adjustment, then swap in my 300 tensioner if the tick is still there.
__________________________________________________
HalfFast Racing Team Serving Greater Houston Area Riders:WFO Riders MotoHouston HPC CMRA Ride Smart Fastline Lone Star Track Days |
|
June 19th, 2015, 05:23 PM | #5 |
ninjette.org certified postwhore
Name: .
Location: .
Join Date: Feb 2011 Motorcycle(s): . Posts: Too much.
MOTM - Feb '13, Feb '14
|
Subbed for write-ups. I'm about to go order a manual one, but I'm researching proper technique for adjusting those first.
|
|
June 19th, 2015, 05:36 PM | #6 |
in your machine
Name: Scott
Location: Summer Shade, Ky.
Join Date: Oct 2014 Motorcycle(s): 98 Ninja 250/F12 aka ZX-2R "SERENITY", 91 Ninja 500/A5 aka ZX-5R "Phoenix", 84 Honda GL1200A "SIREN" Posts: A lot.
Blog Entries: 25
MOTM - Jun '17, May '16, Mar '15
|
Word of warning, I've seen too many adjusted improperly, and blown engines.
__________________________________________________
violente et ignorantia ZX-2R BLOG Twitter and Instagram = Ghostt_Scott I'm not here to change your mind, just to inform. |
|
June 19th, 2015, 06:07 PM | #7 |
ninjette.org certified postwhore
Name: .
Location: .
Join Date: Feb 2011 Motorcycle(s): . Posts: Too much.
MOTM - Feb '13, Feb '14
|
Yeah. Hence looking for proper adjustment method before buying one. Considering manual bs rebuilding the automatic or using a newer model that bolts up.
|
|
June 19th, 2015, 06:11 PM | #8 | ||
ninjette.org certified postwhore
Name: Spooph
Location: Golden, CO
Join Date: Jul 2010 Motorcycle(s): '08 Ninja 250R Posts: A lot.
MOTM - Oct '15
|
Quote:
Quote:
I'd do the tensioner first though, to isolate the clicking...
__________________________________________________
My therapist has 2 wheels and a seat. If you are ever in doubt to my tone, please refer to my avatar. |
||
|
June 19th, 2015, 07:24 PM | #9 |
in your machine
Name: Scott
Location: Summer Shade, Ky.
Join Date: Oct 2014 Motorcycle(s): 98 Ninja 250/F12 aka ZX-2R "SERENITY", 91 Ninja 500/A5 aka ZX-5R "Phoenix", 84 Honda GL1200A "SIREN" Posts: A lot.
Blog Entries: 25
MOTM - Jun '17, May '16, Mar '15
|
@spooph,does rebuilding the old just mean a new spring? Part #92081? Or is there more parts? Or should I just get the whole part #12048?
__________________________________________________
violente et ignorantia ZX-2R BLOG Twitter and Instagram = Ghostt_Scott I'm not here to change your mind, just to inform. |
|
June 19th, 2015, 08:26 PM | #10 | |
RIP Alex
Name: Cuong
Location: Houston, TX
Join Date: Apr 2011 Motorcycle(s): '10 250r, '09 265r Posts: A lot.
Blog Entries: 2
|
Quote:
__________________________________________________
HalfFast Racing Team Serving Greater Houston Area Riders:WFO Riders MotoHouston HPC CMRA Ride Smart Fastline Lone Star Track Days |
|
1 out of 1 members found this post helpful. |
June 19th, 2015, 11:19 PM | #11 |
in your machine
Name: Scott
Location: Summer Shade, Ky.
Join Date: Oct 2014 Motorcycle(s): 98 Ninja 250/F12 aka ZX-2R "SERENITY", 91 Ninja 500/A5 aka ZX-5R "Phoenix", 84 Honda GL1200A "SIREN" Posts: A lot.
Blog Entries: 25
MOTM - Jun '17, May '16, Mar '15
|
__________________________________________________
violente et ignorantia ZX-2R BLOG Twitter and Instagram = Ghostt_Scott I'm not here to change your mind, just to inform. |
|
June 20th, 2015, 12:35 AM | #12 |
Daily Ninjette rider
Name: Hernan
Location: Florida
Join Date: Mar 2011 Motorcycle(s): 2007 Ninja 250 Posts: A lot.
MOTY - 2016, MOTM - Dec '12, Jan '14, Jan '15, May '16
|
The automatic tensioner is a one-way ratcheting mechanism.
The theoretical advantage over a traditional manual adjuster is that it should adjust itself, as the cam chain wears and becomes longer. The disadvantages are: - The spring puts tension on the chain and chain sliders, which accelerates their wear. - The ratcheting mechanism is marginal, once it develops certain wear, it allows excessive chain slack; hence, the noise. About the spring: Its only function is to push the ratcheting mechanism forward as the chain stretches. It is not strong enough to prevent the chain from working loosely. It takes tremendous force to keep the loose (unloaded) side of the chain from moving back and forth (rattling). Only when the rotation of the valve's cams produces the minimum tension on the leg of the chain against which the tensioner works, the spring is able to push and move the plunge to eliminate any chain slack. When the cams produces the maximum tension on that leg of the chain, only the ratcheting effect can keep the plunge in the new position. About the ratcheting mechanism: It is basically a cylindrical plunge surrounded by a ring of balls that get jammed against a conical surface. I said it is marginal, because it is designed for eventual failure: some backing (and consequent loosening of the chain) develops sooner or later. Steel balls have infinitesimally small points of contact and huge contact pressures (Pressure = Force / Area of contact). Those few points of contact feel the previously mentioned high force with which the chain pushes back, multiplied several times by the wedge effect of plunge-conical surface. That high force induces pitting and microscopic deformation of the surfaces of the balls, plunge and cone. The factory neither applies nor recommends lubrication of those parts, which in my opinion accelerates the pitting of the surfaces in contact. Little relative movement and high pressures are the worst conditions for effective lubrication. Once developed, the damage of the points of contact grows, which allows more and more backing up of the plunge. In severe cases, the balls are not round anymore and cannot roll to firmly jam the mechanism in reverse, as originally designed. The case of the pre-gen Ninjas is worst because, rather than directly as with the new-gen tensioner, the plunge pushes via a L-shaped pivot that soon hits the crankcase, stopping any further forward movement before the chain develops its maximum tolerable wear (stretch). About the solution: - Periodic inspection of the contact surfaces and application of high pressure grease. Replace any part that shows any sign of wear, pitting or deformation. - Install a manual tensioner and adjust it during each valve adjustment (bonus: the lack of spring pressure over the chain extends its useful life). There should be a minimum slack left, like for the transmission chain, rather than pressure over the chain, which could break it (a little force exerted by the bolt of the tensioner multiplies the tension in the chain several times). For more information, read this: http://www.dansmc.com/camchain_adjust.htm
__________________________________________________
Motofool .................................Never ride faster than your guardian angel can fly "Mankind is composed of two sorts of men — those who love and create, and those who hate and destroy. Love is the bond between men, the way to teach and the center of the world." - José Martí |
1 out of 1 members found this post helpful. |
June 20th, 2015, 06:12 AM | #13 |
ninjette.org certified postwhore
Name: Spooph
Location: Golden, CO
Join Date: Jul 2010 Motorcycle(s): '08 Ninja 250R Posts: A lot.
MOTM - Oct '15
|
@Ghost - I would pull the tensioner and pull it apart, grease it up and see how long it keeps the rattle at bay...
@Motofool - I'm not sure where the ball bearings you are speaking of are, although I can easily see the same principles apply...
__________________________________________________
My therapist has 2 wheels and a seat. If you are ever in doubt to my tone, please refer to my avatar. |
|
June 20th, 2015, 09:52 AM | #14 | |
Daily Ninjette rider
Name: Hernan
Location: Florida
Join Date: Mar 2011 Motorcycle(s): 2007 Ninja 250 Posts: A lot.
MOTY - 2016, MOTM - Dec '12, Jan '14, Jan '15, May '16
|
Quote:
I have not pulled apart the new-gen tensioner, but the principle is the same.
__________________________________________________
Motofool .................................Never ride faster than your guardian angel can fly "Mankind is composed of two sorts of men — those who love and create, and those who hate and destroy. Love is the bond between men, the way to teach and the center of the world." - José Martí |
|
1 out of 1 members found this post helpful. |
June 20th, 2015, 11:46 AM | #15 | |
The Corner Whisperer
Name: Chris (aka Reactor)
Location: Northern KY
Join Date: May 2011 Motorcycle(s): 2010 250 (track), 1992 250, 2006 R6 (street/track), 2008 R6 (track) Posts: Too much.
MOTY 2015, MOTM - Nov '12, Nov '13
|
Quote:
2. install manual one 3. Adjust finger tight + 1 full turn of the new to "ball park" it 4. start bike and hear it chatter (if no chatter sound loosen it until chatter is heard) 5. adjust SLOWLY (tighten) until chatter goes away 6. back off (loosen) 1/2 or 3/4 turn (very mild chatter will come back) The chain will stretch somewhat over a period of time depending on your riding habits and may need adjusted again. LOCTITE the nut after the 2nd adjustment. It's a chain, better too loose than too tight and don't expect 100% silent operation.
__________________________________________________
Goal: Shake A Million Hands | Look through the corners | Track Day Prep | Closest track? | The Mid-Ohio School |
|
2 out of 2 members found this post helpful. |
June 20th, 2015, 03:24 PM | #16 |
Daily Ninjette rider
Name: Hernan
Location: Florida
Join Date: Mar 2011 Motorcycle(s): 2007 Ninja 250 Posts: A lot.
MOTY - 2016, MOTM - Dec '12, Jan '14, Jan '15, May '16
|
This is what one of the manufacturers of manual tensioner has learned about noise and failure of timing chains:
http://www.clems-garage.com/CCT/about_tensioners.htm Here is the problem and solution for the pivot of the pre-gen Ninjas that I mentioned before: http://www.clems-garage.com/CCT/elim...50_1st_gen.htm
__________________________________________________
Motofool .................................Never ride faster than your guardian angel can fly "Mankind is composed of two sorts of men — those who love and create, and those who hate and destroy. Love is the bond between men, the way to teach and the center of the world." - José Martí |
1 out of 1 members found this post helpful. |
June 20th, 2015, 05:15 PM | #17 |
CPT Falcon
Name: J.Emmett Turner
Location: Newnan, GA
Join Date: Apr 2009 Motorcycle(s): '08 CP Blue EX250J, '97 unpainted EX250F, 2nd '97 unpainted EX250F (no engine), '07 black EX250F Posts: A lot.
|
I don't trust myself and my bad hearing with a manual tensioner and I can't keep buying OEM automatic tensioners, so I'd love to see a J/K/L/300 tensioner teardown/rebuild guide.
|
|
June 25th, 2015, 04:34 PM | #18 |
ninjette.org certified postwhore
Name: TC
Location: Hawaii
Join Date: Sep 2013 Motorcycle(s): A lot. Posts: A lot.
|
I might be in trouble on this one. 27k, 2009. Started hearing clattering from what I thought to be valve noise.
Disassembled and adjusted valves. They are not perfect, as my shim kit only had 0.05mm increments. Two exhaust valves were too tight. Now everything is reassembled. Valves not perfect but all are within specified range. When I got the bike started, minimal clatter noise. After 5 minute idle, slight clatter returned on cam chain/right side of bike. Rode 500 feet, clatter increased. Turned off bike. 5 mins later turned it back on and terrible terrible noise started while idling. Not as terrible as piston/valve contact, but sounds like cam timing chain jumped a tooth. Going to go put it back up on stand, put in neutral and turn over by hand w/spark plugs out to feel for piston/valve interference.
__________________________________________________
Just batshit crazy. All his posts are endless diatribes. Some are actually entertaining but mostly batshit crazy. |
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Changing cam chain | scorch | 2008 - 2012 Ninja 250R Tech Talk | 17 | April 28th, 2014 08:46 AM |
cam chain tensioner | kittyslasher | 2008 - 2012 Ninja 250R Tech Talk | 2 | June 16th, 2013 09:17 AM |
Do cam chain tensioners ever need to be replaced? | Monkeytofu | 1986 - 2007 Ninja 250R Tech Talk | 6 | July 17th, 2012 05:17 PM |
stretched cam chain | alex.s | 2008 - 2012 Ninja 250R Tech Talk | 22 | June 28th, 2012 06:52 PM |
Metal Shavings in Oil, Bad Cam Chain Tensioner? | manorat | 1986 - 2007 Ninja 250R Tech Talk | 1 | August 7th, 2010 12:21 AM |
|
|